Navigation. Spektrum SPM7800C, DX7s 7-Ch, DX7s 7-Ch DSMX Radio System, SPM55101, DX7s Transmitter Only MD2, SPMR7800
Add to My manuals32 Pages
advertisement
![Navigation. Spektrum SPM7800C, DX7s 7-Ch, DX7s 7-Ch DSMX Radio System, SPM55101, DX7s Transmitter Only MD2, SPMR7800 | Manualzz Navigation. Spektrum SPM7800C, DX7s 7-Ch, DX7s 7-Ch DSMX Radio System, SPM55101, DX7s Transmitter Only MD2, SPMR7800 | Manualzz](http://s1.manualzz.com/store/data/002503854_1-7513acdab7e9be265296efaff9b8aa77-360x466.png)
NAVIGATION
Controls for Navigation
• Use the roller, Back and Clear buttons near the LCD screen for DX7s programming.
• Turn or press the roller to move through, select or change screen content.
• Use the Back button to go to the previous screen (for example, to go from the Mixing Screen to the Function List).
• Use the Clear button to change a selected value on a screen to its default setting (Some values do not have a default setting. For example, there is no default alarm type in the Timer
Screen).
• While the transmitter is powered on, go to the Model Select screen by pressing the Clear and Back buttons at the same time. This is Direct Model Access, and will let you go to the
Model Select Screen without powering off and on.
• Press and hold the roller while powering on the transmitter to show the System Setup list. This list is usually used when setting up a model and is not often used at the flying field.
No radio transmission occurs when a System Setup screen is displayed, preventing accidental damage to linkages and servos during changes to programming.
• Powering on the transmitter without touching any controls will show the Main Screen and the active model memory.
Press the roller while on the Main Screen to show the Func-
Turn Press
Press
Enter, Choose or Exit
Turn
Move between options or change value in an option
Hold
Hold for 3 seconds and release to move to the Main Screen
SYSTEM SETTINGS
Use the System Setting screen to establish the overall transmitter setting that will apply to ALL model memories. These settings include: User Name, Contrast, Mode, Region and Language. If you select Mode One, then Mode One will be selected for all 20 model memories. Even when models are imported from an SD card, the system settings in the transmitter will remain.
Accessing System Settings
The Model Select function is used to change to a different model memory, typically when switching from the current model. You can store up to 20 models in the DX7s model memory. Access the model select function through the System Setup mode or through Direct Model Access (pressing the Clear and Back buttons at the same time). Direct Model Access allows you to access the model select function at any time the main screen or a telemetry screen is displayed.
User Name
User Name allows the identification of the owner to be programmed into the transmitter. The user name appears during the startup process at the lower left corner of the startup screen.
To Program a User Name
In the Systems Settings screen rotate the roller to highlight User
Name then press.
Highlight the desired character position then press the roller to access that position. Rotate the roller to change to the desired character. Press to accept.
Contrast
In the Systems Settings screen rotate the roller to highlight User
Contrast then press.
Rotate the roller to adjust the contrast (from 1 to 20) noting it on screen. Press to accept.
Repeat the process until the name is complete. Note that the
User Name displays on the lower left of the startup screen.
Mode
See Appendix for Mode Conversion.
SPEKTRUM DX7s • RADIO INSTRUCTION MANUAL 9
EN
advertisement
Related manuals
advertisement
Table of contents
- 4 Quick Start Guide
- 5 Charging Your Transmitter
- 5 Transmitter Batteries
- 6 Transmitter Functions
- 7 Binding
- 8 Using the transmitter
- 8 Antenna
- 8 Main Screen
- 9 Navigation
- 9 System Settings
- 9 User Name
- 9 Contrast
- 10 Selecting a Region (EU Version)
- 10 Selecting a Language
- 10 Acro and Heli setup
- 11 System Setup
- 11 Model Select
- 11 Model Type
- 11 Model Name
- 11 Switch Select
- 11 Model Reset
- 12 Model Copy
- 12 Warnings
- 12 Telemetry
- 13 Frame Rate
- 13 Wing Type
- 14 Differential
- 14 Flap System
- 14 Swash Type
- 15 Throttle, Pitch and Tail Curves
- 16 Governor
- 16 Flight Mode
- 16 Swashplate
- 17 Function List
- 17 Servo Setup
- 17 D/R & Exponential
- 17 Throttle Cut
- 18 Range Test
- 19 Timer
- 19 Monitor
- 19 Trainer
- 20 Failsafes
- 20 SmartSafe Failsafe
- 20 Hold Last Command
- 20 Preset Failsafe
- 21 Receiver and servo information
- 21 Receiver Installation
- 21 Servo Installation
- 21 Servo Precautions
- 21 Power System Requirements
- 21 Recommended Power System Guidelines
- 22 Appendix
- 22 Mode Conversion
- 23 Installing Optional LiPo Battery Pack
- 24 Servo Control
- 27 Troubleshooting Guide
- 27 Parts list
- 28 AMA National Model Aircraft Safety Code
- 29 FCC Information
- 29 FAA Information
- 31 Warranty and Service Contact Information
- 31 Parts Contact Information
- 31 Compliance Information for the European Union