Booting OmniSwitch 6850 Series Switches. Alcatel-Lucent Switch 6850-U24X, 6850-P24, 6850-P48, 6850-48X, 6850-P24X, 6850-P48X, 6850-24, 6850-P24L, 6850-P48L, 6850-48L
Add to My manuals34 Pages
advertisement
Booting OmniSwitch 6850
Series Switches
Booting a Standalone Switch
The OmniSwitch 6850 Series switch does not use an on/off switch. The power cord is the switch’s only connect/disconnect device. The power connector socket is located on the switch’s rear panel. For more information, refer to the
OmniSwitch 6850 Series Hardware Users Guide.
To boot the switch, plug the power cord (provided) into the power connector socket at the switch’s rear panel. Next, plug the power cord into an easily-accessible power source, such as a grounded AC outlet or an Uninterruptible Power Supply
(UPS).
The switch immediately begins the boot process. Allow a few moments for the switch to boot completely, then verify the status of all LEDs on the switch’s front panel. A successful boot for a standalone switch displays the following LED states:
LED States for a Standalone Switch
OK
PRI
PWR
Solid green
Solid green
Solid green
LED States for a Standalone Switch
BPS
XFP1
XFP2
Slot Indicator
Solid amber, if BPS attached is failed; off, if no operational BPS is attached; solid green if an operational BPS is attached and operating normally.
Off (applies to all OmniSwitch 6850
Series switches except for the
OmniSwitch 6850-24X,
OmniSwitch 6850-P24X,
OmniSwitch 6850-48X,
OmniSwitch 6850-P48X, and
OmniSwitch 6850-U24X).
Off (applies to all OmniSwitch 6850
Series switches except for the
OmniSwitch 6850-24X,
OmniSwitch 6850-P24X,
OmniSwitch 6850-48X,
OmniSwitch 6850-P48X, and
OmniSwitch 6850-U24X).
1–8 (non-blinking), depending on the slot number value in the boot.slot.cfg file. See the OmniSwitch 6850 Series
Hardware Users Guide for detailed information. The default value is 1.
12 Booting OmniSwitch 6850 Series Switches June 2007
If any of the LED state differs from the states shown in the table above, refer to the OmniSwitch 6850 Series Hardware
Users Guide for more information. Contact Alcatel-Lucent
Customer Support if the unexpected LED state persists.
For information on booting stacked configurations and dynamic slot numbering, refer to the OmniSwitch 6850 Series
Hardware Users Guide.
June 2007 Booting OmniSwitch 6850 Series Switches 13
advertisement
Related manuals
advertisement
Table of contents
- 1 (START page)
- 1 Home
- 2 Front Matter
- 2 Safety Information
- 2 Lithium Batteries Warning
- 2 Copyright Information
- 2 Patents
- 2 Contacting Alcatel
- 3 Table of Contents
- 5 OmniSwitch 6850 Series
- 6 Related Documentation
- 7 Installing the Hardware
- 7 Items Required
- 7 Site Preparation
- 7 Environmental Requirements
- 7 Electrical Requirements
- 7 NEBS GR-1089 Compliance Requirements
- 8 Weight Considerations
- 9 Items Included
- 9 Unpacking and Initial Setup
- 9 Unpacking the Chassis
- 9 Recommendations
- 9 Instructions
- 10 Setting Up the Switch
- 10 Airflow Considerations
- 11 Installation Options
- 11 Installing the Switch on a Tabletop or Bench
- 11 Tabletop Mounting Steps
- 12 Rack-Mounting the Switch
- 12 Rack Mounting Steps
- 14 Installing Combo Port SFPs
- 14 Installing Backup Power Supply Components
- 15 Connections and Cabling
- 15 Connecting the Serial Cable
- 15 Serial Connection Default Settings
- 16 Booting OmniSwitch 6850 Series Switches
- 16 Booting a Standalone Switch
- 18 Your First Login Session
- 18 Logging in to the Switch
- 19 Assigning an IP Address to the Switch
- 20 Unlocking Session Types
- 20 Unlocking All Session Types
- 20 Unlocking Specified Session Types
- 21 Changing the Login Password
- 22 Setting the System Time Zone
- 22 Setting the Date and Time
- 22 Setting Optional System Information
- 22 Specifying an Administrative Contact
- 23 Specifying a System Name
- 23 Specifying the Switch’s Location
- 23 Viewing and Saving Changes
- 24 Files and Directories
- 24 Boot and Image Files
- 24 boot.params File
- 24 boot.cfg File
- 25 Image Files
- 26 Working and Certified Directories
- 26 Working Directory
- 27 Certified Directory
- 27 How can I tell which directory the switch is currently using?
- 28 Can I save changes to the Certified directory?
- 28 What happens when the switch boots?
- 28 Working and Certified Are Identical
- 29 Working and Certified Are Different
- 29 My Working and Certified directories are different. Can I force a reboot from the Working directory?
- 30 Using WebView
- 30 Browser Compatibility
- 30 Logging In to WebView
- 31 Navigating WebView
- 33 Online Help
- 33 Additional Information
- 34 Troubleshooting
- 34 The WebView login screen does not display.
- 34 The login screen displays, but the login fails.