advertisement
Installing the LX-4000 Series
Port Status LEDs
Each of the eight (or 16, or 32, or 48) green LEDs flash when receive, transmit, or status activity is detected on its corresponding serial port. The port status LEDs are used in several ways. During the initialization process, the LEDs indicate self-tests are being performed, and if any self-test fails, they indicate an error code. After a POST test and a system software boot, the lights indicate when a port is actively being used.
Rear Panel LEDs
This section explains the rear panel LEDs and shows you a rear view of the various LX-4000 models
(see Figures 5 through 11).
RCV LINK
100-240VAC
1.0A 50/60Hz
DIAG
10/100
ETHERNET
RCV LINK
100
1 2 3 4 5 6 7 8
DIAG Port (Port 0) 100 Mbps
LED
Figure 5 - LX Series 4008 Rear Panel
100-240VAC
1.0A 50/60Hz
Modem Port
LINK
RCV
TELCO
LINE
RCV LINK
100
DIAG/MGMT
10/100 ETH
DIAG Port (Port 0)
10/100
Interface
100
Mbps
LED
Figure 6 - LX Series 4008 with Modem Rear Panel
451-0308
MRV Communications, Inc. www.mrv.com
17
Installing the LX-4000 Series
+ -
A
+ -
B
-24/-48/-60 VDC
1.2 MAX
1 2 3 4 5 6 7 8 9 10 11 12
Modem Port
LINK
RCV
TELCO
LINE
13 14 15 16
RCV LINK
100
DIAG
10/100 ETHNT
DIAG Port (Port 0)
10/100
Interface
100
Mbps
LED
Figure 7 - LX Series 4016 with Modem Rear Panel
RCV
LINK
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 DIAG
10/100
ETHERN ET
RCV LINK
100
DIAG Port (Port 0)
100 Mbps
LED
Figure 8 - LX Series 4016 DC Version Rear Panel
17 18 19 20 21 22 23 24 25 26 27 28
Modem Port
LINK
RCV
TELCO
LINE
29 30 31 32 RCV LINK
100
DIAG
10/100 ETHNT
DIAG Port (Port 0)
10/100
Interface
100
Mbps
LED
Figure 9 - LX Series 4032 with Modem Rear Panel
18
MRV Communications, Inc. www.mrv.com
451-0308
advertisement
Related manuals
advertisement
Table of contents
- 11 Preface
- 11 Customer Support
- 12 Other Documentation
- 13 Overview of the LX-4000 Series
- 13 Conventions
- 14 System Specifications
- 15 Installing the LX-4000 Series
- 15 Hardware Installation
- 15 Unpack and Inspect the Unit
- 15 Package Contents
- 16 LX-4000 Indicators and Interfaces
- 16 Front Panel LEDs
- 17 Rear Panel LEDs
- 19 Environmental and Installation Considerations
- 20 Mounting the Unit into a 19-inch or 23-inch Rack
- 20 Cable Connections
- 20 Connect the Power Cable
- 20 Connecting the Ethernet Interface
- 21 Connect Serial Device Cables
- 21 Connecting Your Management Station
- 21 Connecting DC Power
- 22 Modem Port (Optional)
- 22 Powering On
- 23 System Login and Passwords
- 23 Resetting the Unit
- 25 Configuring the LX-4000 Series for the First Time
- 25 Configuring the LX-4000 Unit for the First Time
- 25 First Time Quick Configuration
- 27 Assigning an IP Address via the Network
- 28 Manually Setting the IP Address Via the CLI
- 28 Accessing and Configuring the Graphical User Interface (GUI)
- 31 Web Configure Mode
- 32 Web Access Mode
- 32 Menu/Config Mode
- 33 GUI EZ Configuration
- 33 Launching the EZConfig GUI
- 34 Software Upgrades
- 34 IP Configuration Menu
- 34 Booting from Defaults
- 34 Accessing and Configuring Additional Features
- 34 Connecting to the LX-4000 Series via Telnet or SSH
- 35 Accessing from a Terminal Attached to an LX-4000 Series Serial Port
- 35 Additional Considerations
- 36 Command Line Interface (CLI) Tree Structure
- 36 Additional Considerations for an Internet Environment
- 36 Autobauding Feature
- 36 Reinitializing/Powering Off the Unit
- 37 Alternative Port Capabilities
- 37 Sensor (Temperature/Humidity) Ports
- 37 Connecting the Temperature/Humidity Sensor
- 38 5250 Power Management
- 39 Connecting the
- 40 5150 Power Strip Management
- 40 Connecting the
- 41 4800 Power Strip Management
- 41 Connecting the
- 42 Using LX Ports as Alarm Inputs and Control Outputs
- 42 Alarm Inputs Setup and Usage
- 43 Control Output Setup and Usage
- 45 Appendix A - Technical Specifications
- 49 Appendix B - Factory Defaults
- 50 ppciboot Factory Default Settings
- 51 Appendix C - POST Test Error Codes
- 51 Error Code Definitions
- 53 POST Test Error Code Sample
- 55 Appendix D - Cabling the LX-4000 Series
- 55 Cabling Considerations
- 55 Serial Device Connectors
- 55 Diagnostic Port Connector (Port 0)
- 56 10/100 Connector
- 56 Ordering Cables
- 56 Modular Adapters
- 56 Pin Assignments
- 58 Ordering and Installing the Inlet Connector Lock
- 58 Connecting to the Diagnostic Port (Port 0)
- 58 Modem Control/Hardware Flow Control
- 59 RJ-45 Wiring Considerations
- 59 Modular Adapters (RJ-45 to DB-25)
- 61 MRV 8-Wire Cabling
- 63 LX Series 4008 Front Panel
- 63 LX Series 4016 Front Panel
- 63 LX Series 4032 Front Panel
- 63 LX Series 4048 Front Panel
- 64 LX Series 4008 Rear Panel
- 64 LX Series 4008 with Modem Rear Panel
- 65 LX Series 4016 with Modem Rear Panel
- 65 LX Series 4016 DC Version Rear Panel
- 65 LX Series 4032 with Modem Rear Panel