advertisement
Configuring the LX-4000 Series for the First Time
Software Upgrades
To upgrade software using the ppciboot menu, refer to “Upgrading Software with the ppciboot Main
Menu” in the LX-Series Configuration Guide. To upgrade software using the CLI, refer to “Upgrading
Software and ppciboot with the Command Line Interface” in the same manual.
IP Configuration Menu
For details on using the IP Configuration Menu, refer to “Using the IP Configuration Menu” in the
LX-Series Configuration Guide.
Booting from Defaults
For information on how to boot your unit from defaults, refer to “Booting from Defaults” in the LX-
Series Configuration Guide.
Accessing and Configuring Additional Features
The following sections describe additional LX-4000 features you can access and configure.
Connecting to the LX-4000 Series via Telnet or SSH
Telnet Directly into the Communication Server
NOTE: The default telnet port is 23. The default SSH port is 22.
1. Telnet to the unit from your machine.
2. Enter your subscriber login name, then your password.
3. If you entered the password correctly, the user> prompt is displayed.
Connecting to a Serial Port
NOTE: Devices connected to serial ports 1-32 on the LX-4032 are assigned telnet port numbers
2100-5200 by default. For example:
• Port 1 = 2100
• Port 2 = 2200
• Port 3 = 2300
NOTE: The corresponding SSH port numbers are 2122-5222. For example:
• Port 1 = 2122
• Port 2 = 2222
• Port 3 = 2322
You can gain telnet/ssh access to a serial device by using the LX IP address and default port number of that serial port.
Changing the Telnet Port
To change the interface telnet port number, use the following commands:
InReach> enable
34
MRV Communications, Inc. www.mrv.com
451-0308
advertisement
Related manuals
advertisement
Table of contents
- 11 Preface
- 11 Customer Support
- 12 Other Documentation
- 13 Overview of the LX-4000 Series
- 13 Conventions
- 14 System Specifications
- 15 Installing the LX-4000 Series
- 15 Hardware Installation
- 15 Unpack and Inspect the Unit
- 15 Package Contents
- 16 LX-4000 Indicators and Interfaces
- 16 Front Panel LEDs
- 17 Rear Panel LEDs
- 19 Environmental and Installation Considerations
- 20 Mounting the Unit into a 19-inch or 23-inch Rack
- 20 Cable Connections
- 20 Connect the Power Cable
- 20 Connecting the Ethernet Interface
- 21 Connect Serial Device Cables
- 21 Connecting Your Management Station
- 21 Connecting DC Power
- 22 Modem Port (Optional)
- 22 Powering On
- 23 System Login and Passwords
- 23 Resetting the Unit
- 25 Configuring the LX-4000 Series for the First Time
- 25 Configuring the LX-4000 Unit for the First Time
- 25 First Time Quick Configuration
- 27 Assigning an IP Address via the Network
- 28 Manually Setting the IP Address Via the CLI
- 28 Accessing and Configuring the Graphical User Interface (GUI)
- 31 Web Configure Mode
- 32 Web Access Mode
- 32 Menu/Config Mode
- 33 GUI EZ Configuration
- 33 Launching the EZConfig GUI
- 34 Software Upgrades
- 34 IP Configuration Menu
- 34 Booting from Defaults
- 34 Accessing and Configuring Additional Features
- 34 Connecting to the LX-4000 Series via Telnet or SSH
- 35 Accessing from a Terminal Attached to an LX-4000 Series Serial Port
- 35 Additional Considerations
- 36 Command Line Interface (CLI) Tree Structure
- 36 Additional Considerations for an Internet Environment
- 36 Autobauding Feature
- 36 Reinitializing/Powering Off the Unit
- 37 Alternative Port Capabilities
- 37 Sensor (Temperature/Humidity) Ports
- 37 Connecting the Temperature/Humidity Sensor
- 38 5250 Power Management
- 39 Connecting the
- 40 5150 Power Strip Management
- 40 Connecting the
- 41 4800 Power Strip Management
- 41 Connecting the
- 42 Using LX Ports as Alarm Inputs and Control Outputs
- 42 Alarm Inputs Setup and Usage
- 43 Control Output Setup and Usage
- 45 Appendix A - Technical Specifications
- 49 Appendix B - Factory Defaults
- 50 ppciboot Factory Default Settings
- 51 Appendix C - POST Test Error Codes
- 51 Error Code Definitions
- 53 POST Test Error Code Sample
- 55 Appendix D - Cabling the LX-4000 Series
- 55 Cabling Considerations
- 55 Serial Device Connectors
- 55 Diagnostic Port Connector (Port 0)
- 56 10/100 Connector
- 56 Ordering Cables
- 56 Modular Adapters
- 56 Pin Assignments
- 58 Ordering and Installing the Inlet Connector Lock
- 58 Connecting to the Diagnostic Port (Port 0)
- 58 Modem Control/Hardware Flow Control
- 59 RJ-45 Wiring Considerations
- 59 Modular Adapters (RJ-45 to DB-25)
- 61 MRV 8-Wire Cabling
- 63 LX Series 4008 Front Panel
- 63 LX Series 4016 Front Panel
- 63 LX Series 4032 Front Panel
- 63 LX Series 4048 Front Panel
- 64 LX Series 4008 Rear Panel
- 64 LX Series 4008 with Modem Rear Panel
- 65 LX Series 4016 with Modem Rear Panel
- 65 LX Series 4016 DC Version Rear Panel
- 65 LX Series 4032 with Modem Rear Panel