- Computers & electronics
- Data storage
- Data storage devices
- Disk arrays
- Panasonic
- WJ-ND400
- Installation Guide
advertisement
22
●
SD memory recording
The SD memory recording is the function featured in some
Panasonic's cameras that records images on the SD memory card on the camera if communication with the camera failed in the period set for the schedule recording of the recorder.
Recording rate setting
The SD memory recording is available only when the camera has this function and "M-JPEG" is selected for compression type of the "Model/Compression" setting on the setup menu of the recorder.
The recording rate of the SD memory recording can be set for each camera channel. The start time of the SD memory recording varies depending on the set recording rate. (Refer to the setup instructions (PDF).)
Obtain image recorded on the SD memory card
It is possible to obtain images recorded on the SD memory card of the camera and save them on the hard disk drive of the recorder.
It is also possible to check if images are currently being obtained or not in the "Status display".
Images recorded on the SD memory card will automatically be obtained at a quarter past the hour (0:15, 1:15 … 23:15).
●
Maintenance (Software upgrade)
It is possible to upgrade the software of the recorder using the web browser. Contact your dealer about the software upgrade.
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 3 Limitation of liability
- 3 Disclaimer of warranty
- 4 Important safety instructions
- 6 Preface
- 6 About the user manuals
- 7 System requirements for a PC
- 7 Trademarks and registered trademarks
- 8 GPL/LGPL
- 8 Copyright
- 8 Network security
- 9 Precautions
- 11 Precautions for installation
- 12 Major operating controls and their functions
- 12 Front view
- 14 Inside the front cover
- 16 Rear view
- 16 Power cord plug brace
- 17 Outline of functions
- 17 HDD (Hard disk drive)
- 17 of storage
- 17 Replacement of the HDD units
- 17 HDD management
- 18 HDD fault-tolerance system
- 18 Recording/Playback
- 18 Stable image recording and playback
- 19 Schedules
- 19 How the event action is taken
- 20 Major functions
- 20 Setup menu and its items
- 20 Network
- 20 Remote operation
- 21 Network security function
- 22 SD memory recording
- 22 Maintenance (Software upgrade)
- 23 Operations flow
- 24 Install the recorder in a rack
- 24 Installation procedure
- 25 Position in the rack
- 26 Connections
- 26 Connection between cameras and PCs
- 26 1-port operation
- 27 2-port operation
- 28 Connection example for 1-port operation
- 30 Connection example for 2-port operation
- 32 Connecting the extension units
- 33 About the connectors
- 33 connector
- 33 Pin configuration
- 34 Connection for emergency recording
- 34 Connection for external recording switching
- 35 function
- 36 Connection of the control output
- 36 (UPS)
- 37 How to use the terminals of the ALARM connector
- 37 Pin configuration
- 38 Alarm connection
- 39 terminal and the ALARM terminal
- 40 Turn on/off the power of the recorder
- 40 Turn on the power of the recorder
- 40 Turn off the power of the recorder
- 40 During recording
- 40 During playback
- 41 Operations using the buttons on the front panel
- 41 Basic operations
- 42 Check the system information
- 43 Check the IP address
- 44 Set the IP address
- 44 How to configure the settings for each item
- 44 Enable/disable the key lock
- 45 HDD unit
- 46 Handle the hard disk drives
- 47 Install the HDD units
- 48 unit at the same time
- 50 Remove the HDD units
- 51 unit at the same time
- 52 Determine the operational mode
- 54 Data recovery (in the RAID 5/RAID 6 mode)
- 55 RAID mode
- 56 Reboot
- 57 Troubleshooting
- 60 Specifications
- 61 Standard accessories
- 62 Index