- Computers & electronics
- Data storage
- Data storage devices
- Disk arrays
- Panasonic
- WJ-ND400
- Installation Guide
advertisement
●
Connection 1 for the auto adjustment time function
When "Auto adjustment time" of "Time & date" under "Basic" on the setup menu is set to "Master"
"Time adjust output" becomes available and the clock of this recorder will be applied to other devices.
The time adjust output signal will be supplied from pin no.20 to other recorders at the time set for "Activation time" of "Time & date" under "Basic" on the setup menu.
Terminal for other devices
Front panel
LED monitor output
(Signal ground)
(Time adjustment output)
13 20
ALARM/CONTROL
●
Connection 2 for the auto adjustment time function
When "Auto adjustment time" of "Time & date" under "Basic" on the setup menu is set to "Slave"
"Time adjust input" becomes available and the clock of this recorder will be applied to other devices.
When a signal output from other device is supplied to the time adjust I/O terminals (pin no.20) 15 minutes before/after the time set for
"Activation time", the clock of the recorder will be set to the time set for "Activation time".
Example:
When "15:00" is set for "Activation time"
• Signal is supplied at 2:50:00 (hour:minute:second) pm → Set at 3:00:00 pm
• Signal input supplied at 3:14:45 pm → Set at 3:00:00 pm
• Signal is supplied at 3:20:00 pm → Time will not be adjusted.
Terminal for other devices
Front panel
LED monitor output
13
(Signal ground)
(Time adjustment input)
20
ALARM/CONTROL
Important:
• When "Slave" is selected, the clock will not be adjusted during event recording or emergency recording.
35
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 3 Limitation of liability
- 3 Disclaimer of warranty
- 4 Important safety instructions
- 6 Preface
- 6 About the user manuals
- 7 System requirements for a PC
- 7 Trademarks and registered trademarks
- 8 GPL/LGPL
- 8 Copyright
- 8 Network security
- 9 Precautions
- 11 Precautions for installation
- 12 Major operating controls and their functions
- 12 Front view
- 14 Inside the front cover
- 16 Rear view
- 16 Power cord plug brace
- 17 Outline of functions
- 17 HDD (Hard disk drive)
- 17 of storage
- 17 Replacement of the HDD units
- 17 HDD management
- 18 HDD fault-tolerance system
- 18 Recording/Playback
- 18 Stable image recording and playback
- 19 Schedules
- 19 How the event action is taken
- 20 Major functions
- 20 Setup menu and its items
- 20 Network
- 20 Remote operation
- 21 Network security function
- 22 SD memory recording
- 22 Maintenance (Software upgrade)
- 23 Operations flow
- 24 Install the recorder in a rack
- 24 Installation procedure
- 25 Position in the rack
- 26 Connections
- 26 Connection between cameras and PCs
- 26 1-port operation
- 27 2-port operation
- 28 Connection example for 1-port operation
- 30 Connection example for 2-port operation
- 32 Connecting the extension units
- 33 About the connectors
- 33 connector
- 33 Pin configuration
- 34 Connection for emergency recording
- 34 Connection for external recording switching
- 35 function
- 36 Connection of the control output
- 36 (UPS)
- 37 How to use the terminals of the ALARM connector
- 37 Pin configuration
- 38 Alarm connection
- 39 terminal and the ALARM terminal
- 40 Turn on/off the power of the recorder
- 40 Turn on the power of the recorder
- 40 Turn off the power of the recorder
- 40 During recording
- 40 During playback
- 41 Operations using the buttons on the front panel
- 41 Basic operations
- 42 Check the system information
- 43 Check the IP address
- 44 Set the IP address
- 44 How to configure the settings for each item
- 44 Enable/disable the key lock
- 45 HDD unit
- 46 Handle the hard disk drives
- 47 Install the HDD units
- 48 unit at the same time
- 50 Remove the HDD units
- 51 unit at the same time
- 52 Determine the operational mode
- 54 Data recovery (in the RAID 5/RAID 6 mode)
- 55 RAID mode
- 56 Reboot
- 57 Troubleshooting
- 60 Specifications
- 61 Standard accessories
- 62 Index