- Computers & electronics
- Data storage
- Data storage devices
- Disk arrays
- Panasonic
- WJ-ND400
- Installation Guide
advertisement
■ How to use the terminals of the ALARM connector
These terminals are used to connect the alarm devices, such as sensors, door switches, etc.
The connector to be used should be compatible with the pin configuration.
●
Pin configuration
The pin array is different from other network disk recorders. Make sure that the connection is correct referring to the following.
The pin configurations of these terminals are as shown below.
13 1
ALARM
25 14
Operation
Event action will be performed according to the settings.
Remarks
Non-voltage make contact, +5 V pull-up 150 kΩ
Pin No.
Signal
1 Alarm input 17
2 Alarm input 18
3 Alarm input 19
4 Alarm input 20
5 Alarm input 21
6 Alarm input 22
7 Alarm input 23
8 Alarm input 24
9 Alarm input 1
10 Alarm input 2
11 Alarm input 3
12 Alarm input 4
13 Signal ground
14 Signal ground
15 Alarm input 25
16 Alarm input 26
17 Alarm input 27
18 Alarm input 28
19 Alarm input 29
20 Alarm input 30
21 Alarm input 31
22 Alarm input 32
23 Alarm input 5
24 Alarm input 6
25 Alarm input 7
Event action will be performed according to the settings.
Non-voltage make contact, +5 V pull-up 150 kΩ
37
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 3 Limitation of liability
- 3 Disclaimer of warranty
- 4 Important safety instructions
- 6 Preface
- 6 About the user manuals
- 7 System requirements for a PC
- 7 Trademarks and registered trademarks
- 8 GPL/LGPL
- 8 Copyright
- 8 Network security
- 9 Precautions
- 11 Precautions for installation
- 12 Major operating controls and their functions
- 12 Front view
- 14 Inside the front cover
- 16 Rear view
- 16 Power cord plug brace
- 17 Outline of functions
- 17 HDD (Hard disk drive)
- 17 of storage
- 17 Replacement of the HDD units
- 17 HDD management
- 18 HDD fault-tolerance system
- 18 Recording/Playback
- 18 Stable image recording and playback
- 19 Schedules
- 19 How the event action is taken
- 20 Major functions
- 20 Setup menu and its items
- 20 Network
- 20 Remote operation
- 21 Network security function
- 22 SD memory recording
- 22 Maintenance (Software upgrade)
- 23 Operations flow
- 24 Install the recorder in a rack
- 24 Installation procedure
- 25 Position in the rack
- 26 Connections
- 26 Connection between cameras and PCs
- 26 1-port operation
- 27 2-port operation
- 28 Connection example for 1-port operation
- 30 Connection example for 2-port operation
- 32 Connecting the extension units
- 33 About the connectors
- 33 connector
- 33 Pin configuration
- 34 Connection for emergency recording
- 34 Connection for external recording switching
- 35 function
- 36 Connection of the control output
- 36 (UPS)
- 37 How to use the terminals of the ALARM connector
- 37 Pin configuration
- 38 Alarm connection
- 39 terminal and the ALARM terminal
- 40 Turn on/off the power of the recorder
- 40 Turn on the power of the recorder
- 40 Turn off the power of the recorder
- 40 During recording
- 40 During playback
- 41 Operations using the buttons on the front panel
- 41 Basic operations
- 42 Check the system information
- 43 Check the IP address
- 44 Set the IP address
- 44 How to configure the settings for each item
- 44 Enable/disable the key lock
- 45 HDD unit
- 46 Handle the hard disk drives
- 47 Install the HDD units
- 48 unit at the same time
- 50 Remove the HDD units
- 51 unit at the same time
- 52 Determine the operational mode
- 54 Data recovery (in the RAID 5/RAID 6 mode)
- 55 RAID mode
- 56 Reboot
- 57 Troubleshooting
- 60 Specifications
- 61 Standard accessories
- 62 Index