- Computers & electronics
- Data storage
- Data storage devices
- Disk arrays
- Panasonic
- WJ-ND400
- Installation Guide
advertisement
40
Turn on/off the power of the recorder
■ Turn on the power of the recorder
Turn on the power of the recorder.
1
Insert the power plug into an outlet.
120 V AC 60 Hz, for the NTSC model
220 V to 240 V AC 50 Hz, for the PAL model
Use the power source that is suited to your model.
2
Press the POWER switch at the rear of the recorder to turn on the power.
• The [OPERATE] indicator will light and the system check
(checking the system and hard disk drives) will start.
• The "WJ-ND400" indication will be displayed on the LCD at startup, and the "Initializing" indication will be displayed during startup.
The "Initializing" indicatior will turn to "Don't turn off" after a short time.
• When the system check is complete, the time and date display (standby display) will be displayed on the LCD.
(Page 41)
Important:
• Do not turn off the power during the power on process.
• When using the extension units (WJ-HDE400), turn on the power of the recorder after turning on the power of all the extension units.
■ Turn off the power of the recorder
To shutdown the recorder, do the following.
Important:
• Remove the plug from the outlet if not operating the recorder not in use long.
• When the recorder has not been used for a certain period, turn on the power of the recorder (approximately once a week) and perform recording/playback to prevent interferences with functions.
●
During recording
1
Select "Off" for "Recording" under "Basic" on the setup menu to stop all recordings. (Refer to the setup instructions (PDF).)
2
Turn off the power of the recorder after confirming that all the HDD access indicators are off.
The [OPERATE] indicator will go off.
Note:
• After turning on the power of the recorder again, do not forget to set the "Recording" setting under "Basic" to "On".
●
During playback
1
Click the [STOP] button on the [HDD] tab on the operation window. (Refer to the operating instructions (PDF).)
2
Turn off the power of the recorder after confirming that all the HDD access indicators are off.
The [OPERATE] indicator will go off.
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 3 Limitation of liability
- 3 Disclaimer of warranty
- 4 Important safety instructions
- 6 Preface
- 6 About the user manuals
- 7 System requirements for a PC
- 7 Trademarks and registered trademarks
- 8 GPL/LGPL
- 8 Copyright
- 8 Network security
- 9 Precautions
- 11 Precautions for installation
- 12 Major operating controls and their functions
- 12 Front view
- 14 Inside the front cover
- 16 Rear view
- 16 Power cord plug brace
- 17 Outline of functions
- 17 HDD (Hard disk drive)
- 17 of storage
- 17 Replacement of the HDD units
- 17 HDD management
- 18 HDD fault-tolerance system
- 18 Recording/Playback
- 18 Stable image recording and playback
- 19 Schedules
- 19 How the event action is taken
- 20 Major functions
- 20 Setup menu and its items
- 20 Network
- 20 Remote operation
- 21 Network security function
- 22 SD memory recording
- 22 Maintenance (Software upgrade)
- 23 Operations flow
- 24 Install the recorder in a rack
- 24 Installation procedure
- 25 Position in the rack
- 26 Connections
- 26 Connection between cameras and PCs
- 26 1-port operation
- 27 2-port operation
- 28 Connection example for 1-port operation
- 30 Connection example for 2-port operation
- 32 Connecting the extension units
- 33 About the connectors
- 33 connector
- 33 Pin configuration
- 34 Connection for emergency recording
- 34 Connection for external recording switching
- 35 function
- 36 Connection of the control output
- 36 (UPS)
- 37 How to use the terminals of the ALARM connector
- 37 Pin configuration
- 38 Alarm connection
- 39 terminal and the ALARM terminal
- 40 Turn on/off the power of the recorder
- 40 Turn on the power of the recorder
- 40 Turn off the power of the recorder
- 40 During recording
- 40 During playback
- 41 Operations using the buttons on the front panel
- 41 Basic operations
- 42 Check the system information
- 43 Check the IP address
- 44 Set the IP address
- 44 How to configure the settings for each item
- 44 Enable/disable the key lock
- 45 HDD unit
- 46 Handle the hard disk drives
- 47 Install the HDD units
- 48 unit at the same time
- 50 Remove the HDD units
- 51 unit at the same time
- 52 Determine the operational mode
- 54 Data recovery (in the RAID 5/RAID 6 mode)
- 55 RAID mode
- 56 Reboot
- 57 Troubleshooting
- 60 Specifications
- 61 Standard accessories
- 62 Index