- Home
- Do-It-Yourself tools
- Garden tools
- Air compressors
- Porter-Cable
- PXCMLC3706056
- Instructions manual
advertisement
MAINTENANCE
BELT TENSION AND PULLEY ALIGNMENT
I WARNING
To avoid personal injury, always shut off and unplug the compressor and relieve all air pressure from the system before performing any service on the air compressor.
NOTE: Drive belt tensioning and pulley alignment are done at the same time.
They are discussed separately for clarity.
ADJUSTING DRIVE BELT TENSION
Proper belt tension and pulley alignment must be maintained for maximum drive efficiency and belt life. The correct tension exists if a deflection (see A) of 1/2”
(13 mm) occurs by placing 5 lb (2.3 kg) of force (see B) midway between the motor pulley and the pump flywheel (See Fig. 8). This deflection can be adjusted by the following procedure. The pulley should be carefully aligned with the flywheel, and all setscrews should be kept tight.
1. Remove the belt guard.
2. Loosen the motor mounting bolts.
3. Shift the motor to the point where the correct deflection exists.
4. Retighten the motor mounting bolts.
5. Check to ensure that the tension remained correct.
6. Reinstall the belt guard. All moving parts must be guarded.
Fig. 8
16- ENG
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 3 SAFETY GUIDELINES
- 6 SPECIFICATION CHART
- 6 OVERVIEW
- 6 Basic Air Compressor Components
- 7 ASSEMBLY
- 7 Assembling the Compressor
- 8 TYPICAL INSTALLATION
- 10 COMPRESSOR CONTROLS
- 11 ELECTRICAL POWER REQUIREMENTS
- 11 Electrical Wiring
- 11 Main Power Panel
- 11 Main Power Disconnect Switch
- 11 Low Voltage Problems
- 11 Grounding Instructions
- 12 MOTOR RESET SWITCH
- 12 OPERATING INSTRUCTIONS
- 12 Break-in of the Pump
- 14 Daily Startup
- 14 Shutdown
- 15 MAINTENANCE
- 15 Draining the Tank
- 15 Checking the Oil
- 15 Changing the Oil
- 16 Belt Tension
- 17 Pulley Alignment
- 18 Cleaning the Air Filter
- 18 Checking the Relief Valve
- 18 Testing for Leaks
- 18 Storage
- 18 SERVICE INTERVAL
- 19 TROUBLESHOOTING CHART
- 21 PARTS DRAWINGS AND PARTS LISTS
- 26 WARRANTY
- 29 GLOSSARY OF TERMS
- 30 PARTS AND SERVICE
- 31 CONSIGNES DE SÉCURITÉ
- 33 TABLEAU DES SPÉCIFICATIONS
- 34 VUE D’ENSEMBLE
- 34 Éléments de base du compresseur d’air
- 35 ASSEMBLAGE
- 35 Assemblage du compresseur
- 36 INSTALLATION TYPIQUE
- 38 COMMANDES DU COMPRESSEUR
- 38 ÉLECTRIQUES
- 38 Câblage électrique
- 39 Panneau de tension principale
- 39 Sectionneur de tension principale
- 39 Problèmes de tension trop basse
- 39 Instructions pour la mise à la terre
- 40 MOTEUR
- 40 MODE D’EMPLOI
- 40 Rodage de la pompe
- 42 Mise en marche quotidienne
- 42 Arrêt
- 43 ENTRETIEN
- 43 Vidange du réservoir
- 43 Vérification du niveau d’huile
- 43 Vidange d’huile
- 44 Tension de la courroie
- 45 Alignement de la poulie
- 46 Nettoyage du filtre à air
- 46 Vérification de soupape de décharge
- 46 Essai d’étanchéité
- 46 Entreposage
- 46 ENTRETIEN PÉRIODIQUE
- 47 DÉPANNAGE
- 54 GARANTIE
- 58 GLOSSAIRE DES TERMES
- 59 PIÈCES ET RÉPARATIONS
- 60 PAUTAS DE SEGURIDAD
- 63 RESUMEN GENERAL
- 63 de aire
- 64 MONTAJE
- 64 Montaje del compresor
- 65 INSTALACION TIPICA
- 67 CONTROLES DEL COMPRESOR
- 68 ELÉCTRICA
- 68 Cableado eléctrico
- 68 Panel principal de alimentación
- 68 Interruptor principal de alimentación
- 68 Problemas causados por bajo voltaje
- 68 Instrucciones de puesta a tierra
- 69 MOTOR
- 69 INSTRUCCIONES OPERATIVAS
- 70 Arranque diario
- 70 Parada
- 72 MANTENIMIENTO
- 72 Desagüe del tanque
- 72 Verificación del nivel de aceite
- 72 Cambio de aceite
- 73 Tensión de la correa
- 74 Alineación de la polea
- 75 Limpieza del filtro de aire
- 75 Revisión de la válvula de alivio
- 75 Detección de fugas
- 75 Almacenamiento
- 75 INTERVALOS DE SERVICIO
- 76 CUADRO DE DETECCIÓN DE FALLOS
- 78 PIEZAS
- 83 GARANTÍA
- 86 GLOSARIO DE TERMINOS
- 87 REPUESTOS Y SERVICIO