Using the Battery
Insert the battery into the camera. Use only a D-LI50 battery.
Charging the Battery
Battery charger D-BC50
Battery D-LI50
AC plug cord
Indicator lamp
When using the battery for the first time, or when the battery has not been used in a long time, or when [Battery depleted] appears, recharge the battery.
Note: AC plug cord “Listed, Type SPT-2 or NISPT-2, 18/2 flexible cord, rated 125 V, 7A, minimum 6ft (1.8m)”
1
Connect the AC plug cord to the battery charger.
2
Plug the AC plug cord into the power outlet.
3
Face the S mark on the exclusive battery up and insert it into the battery charger.
The indicator lamp is lit red during charging.
The indicator lamp turns off when the battery is fully charged.
4
When the battery is fully charged, remove the battery from the battery charger.
2
35
36
2
• Do not use the provided battery charger to charge batteries other than rechargeable lithium-ion battery D-LI50. Charging other batteries may cause damage or heating.
• If the battery is correctly oriented and inserted into the battery charger but the indicator lamp is not lit, the battery is faulty. Install a new battery in the camera.
• The maximum charging time is approximately 180 minutes. Charge in a location where the temperature is between 0°C and 40°C. (Charge time depends on temperature and remaining battery power.)
• If usage time is reduced even when properly charged, the battery has reached the end of its usage span. Install a new battery in the camera.
Inserting/Removing the Battery
When using the battery for the first time, charge the battery and insert it into the camera.
• Do not open the battery cover or remove the battery while the power is on.
• Remove the battery when you will not use the camera for a long while. The battery may leak.
• If the date and time settings have been reset when you insert a new battery
after a long time, follow the procedure for “Setting the Date and Time”. (p.48)
• Insert the battery correctly. If the battery is inserted incorrectly, it may cause camera breakdown. Wipe the electrodes of the battery with a soft dry cloth before inserting.
• Be careful as the camera or battery may become hot when the camera is used continuously for a long period of time.
1
Open the battery cover.
Lift the battery cover unlock lever, turn towards OPEN (1) to unlock, and then pull the cover open (2).
1
2
2
Face the S mark on the battery towards the monitor, push
the battery lock lever in the direction of the arrow (1) and insert the battery.
Insert until the battery locks.
To remove the battery, push the battery lock lever in the direction of the arrow (1) with your hand. The battery pops out slightly. Remove it.
1
37
2
Battery lock lever
3
Close the battery cover (1) and turn the battery cover unlock lever towards CLOSE
(2) to lock.
Stow the battery cover unlock lever when finished closing.
2
1
Use the AC adapter D-AC50 (optional) when using the camera for a prolonged
period. (p.39)
38
Battery Level Indicator
2
You can confirm remaining battery level by checking the { displayed on the LCD panel.
: Battery is full.
{ lit
¶
} lit
¶
?
lit
¶
?
blink
: Battery is running low.
: Battery is almost empty.
: The camera turns off after displaying a message.
• } may appear even when the battery level is sufficient if the camera is used at low temperatures or when performing continuous shooting consecutively. Turn the camera off and on again. If { appears, you can use the camera.
• { does not appear on the LCD panel when using the AC adapter.
Approximate Image Storage Capacity and
Playback Time (Exclusive Battery Fully Charged)
Battery
Normal recording
Flash photography
50% use 100% use
530
430
420
320
Playback time
D-LI50
(Temperature)
(23°C)
( 0°C)
740
700
330 minutes
300 minutes
The picture storage capacity (flash use 50%) is based on measuring conditions in accordance with CIPA standards and the others are based on PENTAX measuring conditions. Some deviation from the above figures may occur in actual use depending on shooting mode and shooting conditions.
• Battery performance temporarily decreases as the temperature decreases.
When using the camera in cold climates, have extra batteries on hand and keep them warm in your pocket. Battery performance will return to normal when returned to room temperature.
• Have extra batteries ready when traveling overseas, taking pictures in cold climates, or when you will be taking a lot of pictures.
• If usage time is reduced even when properly charged, the battery has reached the end of its usage span. Install a new battery in the camera.
Using the AC Adapter (Optional)
1 2
We recommend using the AC adapter D-AC50 (optional) when using the monitor for a long time or when connecting to your PC.
1
Make sure the camera is turned off and open the terminal cover.
2
Face the S mark on the DC terminal of the AC adapter
towards the S mark on the camera, and connect the DC terminal to the DC input terminal of the camera.
3
Connect the AC plug cord to the AC adapter.
4
Plug the AC cord into the power outlet.
• Make sure the camera is turned off before connecting or disconnecting the
AC adapter.
• Make sure connections are secure between the camera, AC adapter, AC plug cord terminal and the power outlet. SD Memory Card and data will be corrupted if disconnected while camera is recording or reading data.
• Be sure to read the AC adapter D-AC50 operating manual when using the
AC adapter.
• The battery in your camera will not charge when connected to the AC adapter.
2
39
