Emergency Dial/Push-to-talk (PTT). Spectralink NetLink 8030, NetLink 8020

1725-36024-001-C.book Page 8 Tuesday, December 8, 2009 3:00 PM

Emergency Dial/Push-to-talk (PTT)

 The large button on the left side of the SpectraLink

8030 Wireless IP Telephone may provide you with either Emergency Dial or PTT as determined and acti-

Press this button one time. If Emergency Dial is active, an explanatory message will be displayed.

activated by the system administrator.

Emergency Dial

When Emergency Dial has been enabled, the handset will dial an emergency

Emergency Dial

Config Menu>System Info option.

When Emergency Dial has been enabled, the handset will dial an emergency number when it is pressed twice within two seconds. The number dialed may be found under the Config Menu > System Info option.

!

Caution! Emergency Dial will be inoperable if the wire-

Caution! less system or the call server fails for any reason. Do not rely on it as your sole method of emergency notification.

emergency notification.

Push-to-talk (PTT)

Push-to-talk (PTT)

group broadcast mode, where a single handset can transmit to multiple listeners, like a two-way radio.

spectralink spectralink spectralink spectralink spectralink

1

4GHI

7PQRS

*

FCN

2ABC

5JKL

8TUV

0

3DEF

6MNO

9WXYZ

#

LINE

Transmitter

Transmitter

If you want to

8

Respond to a PTT call

1

4GHI

7PQRS

*

FCN

2ABC

5JKL

8TUV

0

3DEF

6MNO

9WXYZ

#

LINE

1

4GHI

7PQRS

*

FCN

2ABC

5JKL

8TUV

0

3DEF

6MNO

9WXYZ

#

LINE

Receivers

Receivers

1

4GHI

7PQRS

*

FCN

2ABC

5JKL

8TUV

0

3DEF

6MNO

9WXYZ

#

LINE

1

4GHI

7PQRS

*

FCN

2ABC

5JKL

8TUV

0

3DEF

6MNO

9WXYZ

LINE

#

Then

English

Transmitting and then hold the handset approximately two inches from your mouth and speak.

Press and hold the TALK button during the 10-second wait period.

7

If you want to

Select a different

PTT channel

Then

Press and release the TALK button.Use the Nav keys or volume side buttons to highlight the desired channel.

End one PTT call and Press the END key to exit the PTT call. Press and release

TALK button and select a different channel from the list.

Press and hold the TALK button to begin transmitting on the different channel.

Receive to a PTT call Press the END key to end the telephone call. Now you can

while on a telephone call hear the PTT call.

Transmit on the

priority channel

End a PTT call

Press and release the TALK button. Select the priority channel from the list. Press and hold TALK, then speak.

Press the END key to exit the PTT call.

Change the PTT volume Press the up/down volume buttons on the side of the handset while transmitting or receiving a PTT call.

Answer a telephone call Press the START key. PTT transmissions will be

during a PTT transmission pre-empted by the telephone call.

Enable PTT vibrate To enhance the alerting of a PTT call, PTT Vibrate may be enabled. When PTT Vibrate is enabled, the handset will vibrate three times whenever a PTT broadcast is received, whether the handset is in standby or in a call.

If in a call, the chirp alert will also sound. The vibration does not replace any PTT tone volume already set. To set the handset for PTT vibrate only, enable PTT Vibrate and set the tone volume to zero.

Start a telephone call Press the START key and dial the number. PTT

during a PTT transmission transmissions will be pre-empted during the telephone call.

Turn off PTT Change to a different profile (Silent and Vibrate disable

PTT by default).

Subscribe to additional

PTT channels

Press the Cfg softkey to open the Config Menu and select

Push-to-talk. Select Subscribed Channels and then select the channels you want to add. Subscribed channels are marked with an asterisk (*).

8