- Computers & electronics
- Audio & home theatre
- Supplementary music equipment
- Panasonic
- WJ-NV300K/G
- Installation Guide
Installation or replacement of the hard disk drives. Panasonic WJ-NV300, WJ-NV300K, WJ-NV300K/G
Add to my manuals48 Pages
advertisement
Installation or replacement of the hard disk drives
Before installing the hard disk drives, turn off the power of the recorder first. When replacing the hard disk drives, the procedures will be same as those of installation. When installing or replacing the hard disk drives for playback use only (hard disk drives that are formerly used for recording), perform the link process.
Important:
• When securing the hard disk drives to the HDD brackets, do not mistake the direction of the connectors. (Do not install the
• hard disk drives in the opposite direction.)
When installing hard disk drives, use a low-torque powered screwdriver or a torque screwdriver to tighten screws with the
• specified torque.
Hard disk drives are precise devices. Handle with care while keeping the following in mind.
•
•
Do not subject the hard disk drive to any vibration or impact.
Before touching the hard disk drive, eliminate static electricity by touching a steel locker, etc. When holding the hard disk
•
•
•
• drive, hold the both sides of the hard disk drive.
Do not touch the circuit board or the connectors to prevent the hard disk drive from damaging by static electricity.
Contact your dealer for hard disk drives that works on the recorder. Please be forewarned that operation with any hard disk drive other than the specified models is not guaranteed under any circumstances.
When using multiple hard disk drives, use the same model.
If different models are used together, even when the capacities of them are the same, the available capacity may be a few percent smaller.
Note:
• Hard disk drives are locally procured. Contact your dealer for purchasing, installing, and replacing the hard disk drives.
Install the hard disk drives
Installation or replacement of the hard disk drives
Step 1
Turn off the power of the recorder. (☞ Page 35)
Step 2
Remove the HDD bracket screws (x2) on the HDD slots on the rear panel of the recorder, and pull out the HDD bracket.
Step 3
Install the hard disk drive into the HDD bracket using 4 HDD fixing screws (accessories).
Tightening torque for the screws: 0.49 N·m {0.36 lbf·ft}
HDD fixing screw (accessory)
HDD fixing screw (accessory)
32
HDD bracket screw
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 4 Limitation of liability
- 4 Disclaimer of warranty
- 4 Warranty for U.S
- 5 Important safety instructions
- 7 Preface
- 7 Features
- 8 About the user manuals
- 9 System requirements for a PC
- 9 Trademarks and registered trademarks
- 10 Abbreviations
- 10 GPL/LGPL
- 10 Copyright
- 10 Network security
- 11 About the face matching function (option)
- 11 Notation about the installation and setup of the camera
- 14 Precautions
- 17 Precautions for installation
- 18 Major operating controls and their functions
- 18 Front view
- 20 Rear view
- 22 User/Host management
- 22 When operating from a PC via a network
- 23 Operations flow
- 24 Connection
- 24 Connection of cameras
- 25 Connection of monitors
- 26 Connection of a PC
- 28 Connection of extension units
- 29 About the connector
- 29 How to use the terminals of the ALARM/CONTROL connector
- 31 Time and polarities of the ALARM/CONTROL connector
- 32 Installation or replacement of the hard disk drives
- 32 Install the hard disk drives
- 33 Replace the hard disk drives
- 34 Turn on the recorder
- 34 Turn on the power of the recorder
- 35 Turn off the power of the recorder
- 36 Register the license (Registration Key)
- 38 Basic operations
- 40 Setup menu
- 41 Configure the minimum settings [Easy Start]
- 44 Troubleshooting
- 46 Specifications
- 47 Standard accessories