advertisement
USERS QUICK REFERENCE GUIDE
SETUP CHECKLIST
Turn on all system components including the video source you intend to watch; video source is the video equipment connected to the HD
Display connection center.
Turn on the HD Display.
Select a video source from one of the video inputs provided on the connection center: Video
In, S-Video In, or RGB input jacks.
Set the HD Display internal clock.
The internal clock must be set before the Timer
Menu option will appear in the Setup Main Menu.
Select English, Spanish, French, or German for onscreen menus.
Use other options (fine-tune video image).
BASIC OPERATION: PROJECTING A PICTURE (Remote operates HD Display in TV mode)
Once the HD Display has been installed and set up, follow these simplified instructions for operation.
Be sure to install batteries in the remote.
6 power cable aux 1 aux 2 tv vcr
Projecting a Picture
1. Press Mode repeatedly on remote to select TV mode.
2. Point remote toward HD Display screen, press POWER to turn HD Display on. (Be sure all video sources are also turned on.)
3. Press Trackball down to place cursor on the HD Display screen.
4. Rotate trackball toward top of screen until Source menu appears, select the video source you want to project.
5. Make any necessary on-screen adjustments using the
Setup and Video Menus.
6. When finished using the HD Display, select TV mode, press POWER to turn the HD Display off.
1/6
3/4 vo lu m e
1
4 mute mode surf
2
5 flshbk ch an ne l
3
6
8
Audio Amplifier Note:
Reference is made to an audio amplifier. The user-supplied audio amplifier may be a stereo system. In that case, connect
Right and Left Audio Out from the video source you are using to Right and Left Audio In on the audio amplifier.
7 source menu record pip
0
9 enter quit/ pause
2 rew play stop ffwd
P A G E 9
206-3275-A
advertisement
Related manuals
advertisement
Table of contents
- 2 SAFETY WARNINGS
- 4 IMPORTANT SAFETY INSTRUCTIONS
- 6 Installer’s Experience Level
- 6 Installation Considerations
- 6 National Power Cord Requirements U.S., Canada
- 7 Connections Center
- 7 Connections Options
- 7 Description/Function
- 8 Connecting Computer Video Sources
- 8 Connecting Video and S-Video Sources
- 9 Setup Checklist
- 9 Basic Operation: Projecting a Picture
- 10 Using a Computer as a Video Source
- 11 Communications Port Inter-Connection Wiring Reference
- 12 Using a VCR or other Video Source
- 13 Using an S-Video VCR or other S-Video Source
- 14 Introduction
- 14 Battery Installation
- 14 Programming Your Remote to Operate Other IR Devices
- 15 Basic Operations
- 17 Other Brand Equipment Programming Codes
- 18 Remote Key Functions in Other Operating Modes
- 19 Amplifier Volume Override
- 19 Cable Volume Override
- 20 Auto Find: Automatic Brand Code Search
- 20 Cleaning The Trackball
- 21 Available Menus
- 21 Features)
- 22 Trackball Menu
- 22 Status, Copy, Sleep Timer, Z-Trak, Store
- 22 Sleep Timer
- 22 Source/Time Display
- 23 Available Source Menu Options: Video, S-Video, RGB
- 23 Changing Input Source
- 23 Input Sources
- 24 Setup Menu Options
- 25 Clock Set
- 25 Timer Setup
- 25 On/Off Timer
- 25 Enable/Disable On/Off Timer
- 26 Language
- 26 Video Mode
- 26 Aspect Ratio (Picture Proportion)
- 27 Format Pref. (Preference)
- 27 Label Format
- 27 Blank Setup
- 28 Static Setup (Red, Blue, Green Convergence)
- 29 Adjustments
- 29 Video Menu Options
- 30 RGB Source Special Adjustments
- 31 Caring for Your HD Projection Display
- 31 Cabinet Care
- 31 Lens Cleaning
- 31 Extended Absence
- 31 Picture Interference
- 32 Before Calling For Service
- 32 Problem Identification Chart
- 32 RGB Source Problems
- 35 Notes