- Home
- Home security & automation
- Carbon monoxide (CO) detectors
- Intec Controls
- PolyGard MGC2-20
- User manual
4.4 Menu Sensor Readings. Intec Controls PolyGard MGC2-20, PolyGard MGC2-04, PolyGard MGC2-24, PolyGard MGC2-16, PolyGard MGC2-12, PolyGard MGC2-08
Add to My manuals34 Pages
advertisement
MGC2 – UserManual
Specifications subject to change without notice. | USA 160811 | Page 11 of 34
4.4 Menu Sensor Readings
In this menu, the display shows the current value (CV), the gas type and the defined control mode (CV or AV mode) for each active sensor point.
In the control mode Average Value (AV), both values (CV and AV) are displayed.
The SP address and the display depend on the system parameter settings for the SP addressing mode (see 4.8.3)
SP01 CO ppm
50 AV 33 CV
Symbol Description Setting
Status
Function
SPXX
CO ppm
CV
Measured value
Gas type
Gas unit
Current value
AV Average value
* Control mode
Not active Status SP
Error
Locked
Malfunction SP
SP locked
Measured value analog transmitter
See 4.6.2
See 4.6.2
Current value of gas concentration
Average value (10 measured values within the time unit)
Display of selected control mode (CV or AV evaluation)
SP not active
Communication error, or signal out of the measuring range
SP was temporarily locked by the operator.
PolyGard ® is a registered trademark of MSR-Electronic GmbH
12700 Stowe Drive, Suite 100, Poway, CA 92064 | Ph: (858) 578.7887 & (888) GO.IN
TEC | relevantsolutions.com/inteccontrols
advertisement
advertisement
Table of contents
- 4 1 Application
- 4 2 Description
- 4 2.1 Normal Mode
- 4 2.2 Alarm Mode
- 4 2.3 Fault Mode
- 5 3 Operating Instruction
- 5 3.1 Description Keypad User Interface
- 5 3.2 Setting / Change Parameters or Setpoints
- 6 3.3 Code Levels
- 7 4 Menu Overview
- 8 4.1 Fault Management
- 8 4.1.1 Acknowledge a Fault
- 8 4.1.2 Error Memory
- 9 4.1.3 System Errors
- 10 4.2 Status Alarm
- 10 4.3 Status Relay
- 10 4.3.1 Manual Operation of the Relays
- 11 4.4 Menu Sensor Readings
- 12 4.5 Menu Relay Parameter
- 12 4.5.1 Relay Mode
- 12 4.5.2 Relay Function Static / Flash
- 13 4.5.3 Latching Mode
- 13 4.5.4 Horn Function
- 14 4.5.5 External Operation of Alarm Relay
- 14 4.5.6 Delay Mode of Alarm Relay
- 15 4.6 Menu SP Parameter
- 16 4.6.1 Activate – Deactivate SP
- 16 4.6.2 Lock or Unlock SP
- 17 4.6.3 Selection Gas Type
- 18 4.6.6 Threshold/Hysteresis
- 18 4.6.7 Delay for Alarm ON and/or OFF
- 19 4.6.8 Control Mode Current or Average Value
- 19 4.6.9 SP Fault Assigned to Alarm
- 19 4.6.10 Alarm Assigned to Alarm Relay
- 19 4.6.11 SP Signal Assigned to Analog Output
- 20 4.7 Menu Data Logger
- 20 4.7.1 Data Logger Switch On/Off
- 21 4.7.2 Current Value
- 22 4.7.3 CV Log Rate
- 22 4.7.4 Alarm Status
- 23 4.7.5 Error Status
- 24 4.8 Menu System Parameter
- 26 4.8.1 Service Mode
- 26 4.8.2 Software Version
- 26 4.8.3 SP Address Mode
- 26 4.8.4 Language
- 26 4.8.5 Maintenance Concept
- 27 4.8.6 Average Function
- 27 4.8.7 System Time, System Date
- 27 4.8.8 Service Password (Maintenance)
- 27 4.8.9 GC Address
- 28 4.8.11 Acknowledge a Relay in Latching Mode by a DI
- 28 4.8.12 Power On Time
- 28 4.8.13 Registration of Expansions Modules
- 29 4.8.14 Error Indicator System Bus
- 29 4.8.15 Analog Output
- 30 4.8.16 Relay Multiplication
- 31 5 Programming Operation
- 31 5.1.2 Analog Output Setup
- 32 5.1.3 Relay Setup
- 33 5.1.4 Sensor Setup
- 34 6 Notes & General Information
- 34 6.1 Intended Product Application
- 34 6.2 Installer’s Responsibilities
- 34 6.3 Maintenance
- 34 6.4 Limited Warranty