advertisement
![Handling SIPs. Cisco 10000 SIP-600 | Manualzz Handling SIPs. Cisco 10000 SIP-600 | Manualzz](http://s2.manualzz.com/store/data/060163119_1-764345e04cd2378d7af7281d494c15a5-360x466.png)
C H A P T E R
5
Installing and Removing a SIP
•
•
•
This chapter describes how to install or remove SIPs on a Cisco 10000 series router. This chapter contains the following sections:
Online Insertion and Removal of a SIP, page 5-46
SIP Installation and Removal, page 5-49
Handling SIPs
Each SIP circuit board is mounted to a metal carrier and is sensitive to electrostatic discharge (ESD) damage. Before you begin installation, read
Chapter 4, “Preparing to Install a SIP or a SPA,”
for a list of parts and tools required for installation.
Caution Always handle the SIP by the carrier edges; never touch the SIP components or connector pins
(see
When a slot is not in use, a blank filler plate must be installed in the empty slot to allow the router to conform to electromagnetic interference (EMI) emissions requirements and to allow proper airflow across the installed modules. If you plan to install a SIP in a slot that is not in use, you must first remove the two blank filler plates.
OL-13838-01
Cisco 10000 Series Router SIP and SPA Hardware Installation Guide
5-45
advertisement
Related manuals
advertisement
Table of contents
- 7 Objectives
- 7 Audience
- 8 Document Revision History
- 8 Organization
- 9 Related Documentation
- 9 Obtaining Documentation, Obtaining Support, and Security Guidelines
- 11 Introduction to SIPs and SPAs
- 11 SPA Interface Processors
- 12 Shared Port Adapters
- 12 SIP and SPA Compatibility
- 13 Modular Optics Compatibility
- 14 Power Management
- 15 SIP Summary
- 15 Checking Hardware and Software Compatibility
- 16 Identifying Slots and Subslots for SIPs and SPAs
- 16 Specifying the Slot Location for a SIP
- 19 Specifying the Location for a SPA
- 20 Cisco 10000 SIP-600 Overview
- 20 Cisco 10000 SIP-600 Processor
- 20 Cisco 10000 SIP-600 LED
- 22 Cisco 10000 SIP-600 Physical Specifications
- 23 Bandwidth Oversubscription
- 25 SIP Ingress Oversubscription
- 25 PRE4 Egress Oversubscription
- 25 SIP Performance with a PRE3
- 26 1-Port 10-Gigabit Ethernet SPA Overview
- 27 1-Port 10-Gigabit Ethernet SPA LEDs
- 27 1-Port 10-Gigabit Ethernet SPA XFP Optical Transceiver Modules, Connectors, and Cables
- 27 XFP Connections
- 29 XFP Port Cabling Specifications
- 29 2-Port Gigabit Ethernet SPA Overview
- 29 2-Port Gigabit Ethernet SPA LEDs
- 30 2-Port Gigabit Ethernet SPA Cables and Connectors
- 30 SFP Module Connections
- 31 SFP-GE-S Modules
- 31 SFP-GE-L Modules
- 32 SFP-GE-Z Modules
- 32 SFP-GE-T Modules
- 32 SFP Module Cabling and Connection Equipment
- 33 5-Port Gigabit Ethernet SPA Overview
- 33 5-Port Gigabit Ethernet SPA LEDs
- 34 5-Port Gigabit Ethernet SPA Cables and Connectors
- 34 SFP Module Connections
- 35 SFP-GE-S Modules
- 36 SFP-GE-L Modules
- 36 SFP-GE-Z Modules
- 36 SFP-GE-T Modules
- 36 SFP Module Cabling and Connection Equipment
- 37 8-Port Gigabit Ethernet SPA Overview
- 37 8-Port Gigabit Ethernet SPA LEDs
- 38 8-Port Gigabit Ethernet SPA Cables and Connectors
- 38 SFP Module Connections
- 39 SFP-GE-S Modules
- 39 SFP-GE-L Modules
- 40 SFP-GE-Z Modules
- 40 SFP Module Cabling and Connection Equipment
- 41 2-Port Channelized OC-12/DS0 SPA
- 41 2-Port Channelized OC-12/DS0 SPA LEDs
- 42 2-Port Channelized OC-12/DS0 SPA Interface Specifications
- 42 2-Port Channelized OC-12/DS0 SPA SFP Optical Transceiver Modules and Cables
- 45 Required Tools and Equipment
- 45 Safety Guidelines
- 45 Safety Warnings
- 46 Warning Definition
- 50 Electrical Equipment Guidelines
- 50 Telephone Wiring Guidelines
- 51 Preventing Electrostatic Discharge Damage
- 51 Laser/LED Safety
- 55 Handling SIPs
- 56 Online Insertion and Removal of a SIP
- 57 Deactivating a SIP
- 57 Reactivating a SIP
- 57 Verifying the Status of a SIP
- 59 SIP Installation and Removal
- 59 Installing a SIP
- 62 Removing a SIP
- 67 Handling SPAs
- 68 Online Insertion and Removal of a SPA
- 68 Deactivating a SPA
- 69 Reactivating a SPA
- 69 Verifying the Status of a SPA
- 70 Installing a SPA in a SIP
- 70 Removing a SPA from a SIP
- 70 Optical Device Maintenance
- 71 Cleaning Optical Devices
- 71 Checking the Installation
- 71 Verifying the Installation
- 72 Using show Commands to Verify SPA Status
- 72 SPA Blank Filler Plates
- 73 Troubleshooting
- 74 Using debug Commands
- 75 Packing a SPA for Shipment
- 75 Packing a SIP for Shipment