Plot Mode Graphics Operational Description. Genicom P600, 5000 Series, GEK 00031B, GEK 00031B
Add to My manuals314 Pages
advertisement
![Plot Mode Graphics Operational Description. Genicom P600, 5000 Series, GEK 00031B, GEK 00031B | Manualzz Plot Mode Graphics Operational Description. Genicom P600, 5000 Series, GEK 00031B, GEK 00031B | Manualzz](http://s1.manualzz.com/store/data/060440337_1-a640461aff3125ee63f89eb2c9daf7a4-360x466.png)
PLOT MODE GRAPHICS OPERATIONAL DESCRIPTION
Plot Density
Plot density refers to the number of dots per inch (dpi) printed in a single dot row. Two types of plot density are available in this emulation:
▪ Normal density plot mode
▪ Double density plot mode
Normal Density Plot Mode
▪ Selected using the odd dot plot control code ENQ (05 hex) or the
“SFCC e” control sequence.
▪ The odd-numbered dot columns (120 DPI grid) are addressed to produce a horizontal density of 60 DPI.
Double Density Plot Mode
▪ Selected using the even dot plot control code EOT (04 hex), or the
“<SFCC> d” control sequence. The even dot mode must be used in conjunction with the odd dot plot control code ENQ (05 hex) or
“<SFCC> e” sequence.
▪ The even dots are sent first, followed by the odd dots, allowing a maximum of 1632 dots in a single dot row at 120 dpi (13.6 inch line).
▪ The vertical density remains the same as in normal density plotting.
Plot Mode Format
▪ Each data byte specifies six possible dot columns.
▪ Using odd dot plot, bits 1 to 6 of the data byte address the oddnumbered dot columns; using even dot plot, bits 1 to 6 of the data byte address the even-numbered dot columns.
▪ Bit 6 and/or bit 7 of the data byte must be a 1 (true) bit in the
Plot mode.
▪ Bit 8 of the data byte is ignored in Plot Mode; it can be either 1 or
0.
▪ The binary equivalent of the plot data bytes must be known in order to accurately address specific dot positions.
Chapter 4. Printronix P Series Emulation
98
GEK-00029B
advertisement
Related manuals
advertisement
Table of contents
- 8 Chapter 1.Introduction
- 8 overview of printer emulation
- 8 Control Codes
- 8 Escape Sequences
- 9 CSI and OSC
- 10 Line Terminators
- 10 Decipoints
- 10 SCS Smart Graphics Capabilities
- 11 Chapter 2. ANSI Emulation
- 11 Control Code and Escape Sequence Activity Levels
- 11 Notes
- 12 Control Code Activity Levels
- 13 Escape Sequence Activity Levels
- 14 Control Code Definitions
- 16 Escape Sequence Directory
- 18 ANSI ESCAPE SEQUENCE CATEGORIES
- 19 Housekeeping Sequences
- 22 Character Set Selection
- 23 Character Map Load
- 25 Paper and Print Position Movements
- 28 Margins and Tabs
- 31 Font Handling and Enhancements
- 36 Graphics
- 36 Six-Bit Graphics
- 36 Dot Patterns and Densities
- 38 Horizontal Format
- 38 Vertical Format
- 39 Eight-Bit Graphics
- 39 Horizontal Format
- 39 Vertical Format
- 40 Other Graphics Considerations
- 40 Graphics Sequences
- 42 Electronic Vertical Format Unit - EVFU
- 42 Downloading the EVFU
- 42 Loading the Table
- 43 BASIC Programming Example for EVFU Table Loading
- 44 EVFU Default
- 44 Skip to Channel Command
- 45 BASIC Programming Example for Skip to Channel
- 46 Bar codes
- 46 Entering and Exiting Bar Codes
- 46 ANSI 4800/4410 Strap 1 OUT
- 46 ANSI 4800/4410 Strap 1 IN
- 47 Setting Bar Code Parameters
- 48 Bar Code Dimensions
- 50 Default Bar Code Characteristics
- 50 Human-Readable Line (HRL)
- 50 Font Styles and Enhancements
- 50 Spacing and Bar Code Editing Aids
- 51 Bar Code Readability Statement
- 52 Bar Code Program Examples
- 52 Test Program
- 52 Error Symbol
- 53 Changing Parameters
- 53 Commas and Spaces as Delimiters
- 54 Horizontal Spacing
- 55 Printer Option Strap 11, Group 2 IN
- 55 EXAMPLE 1: Strap 11 OUT
- 55 EXAMPLE 2: Strap 11 IN
- 57 Vertical Bar Codes
- 57 COMMAS: With HRL
- 58 COMMAS: Without HRL
- 58 SPACES: With HRL
- 58 SPACES: Without HRL
- 59 Horizontal Tabs
- 60 OVERSIZE CHARACTER FONT
- 60 Entering and Exiting Oversize
- 61 Selecting Size
- 61 Size Parameters for Rotation
- 61 Spacing Between Characters
- 62 Sample Programs
- 62 Example
- 64 Printer Control Strap GenPrtOpts/Group 2/Strap
- 65 Example 4: GenPtrOpts | Group 2 Strap 13 IN
- 65 Example 5: GenPtrOpts | Group 2 Strap 13 OUT
- 66 Chapter 3.Printronix P300/P600 Emulation
- 66 Introduction
- 66 Control Codes
- 69 Printronix Graphics
- 69 Dot Patterns and Densities
- 70 Dot Patterns
- 71 Normal-Density Graphics
- 71 High-Density Graphics
- 71 P300/600 8-Bit Horizontal Graphics
- 72 P300/600 Electronic Vertical Format Unit
- 72 Using the EVFU
- 72 Points to Remember
- 73 PI Lead Codes – Use with Serial Interface
- 73 Codes Not Using the PI Lead
- 74 Example EVFU Loading Program
- 75 Example Form Printout
- 75 Sample Program to Print Form
- 76 Chapter 4.Printronix P-Series Emulation
- 76 Special Function Control Character (SFCC)
- 76 Command Line
- 77 Set and Reset Codes
- 78 Command Index
- 80 Control Codes
- 82 character sets, FONT handling and enhancements
- 92 Housekeeping Commands
- 98 Plot Mode Graphics Operational Description
- 98 Plot Density
- 98 Normal Density Plot Mode
- 98 Double Density Plot Mode
- 98 Plot Mode Format
- 99 Plot Data Line Format
- 99 Normal Density Plot Mode Format
- 100 Double Density Plot Mode Format
- 101 Plot Mode Graphic Character Chart
- 101 Exiting Plot Mode Graphics
- 102 Plot Mode Graphics density commands
- 104 Differences From Target Printer Emulation
- 104 Discarded Commands
- 104 Select Extended Character Set (SFCC OSET;n)
- 104 Download a Language (SFCC V)
- 104 Download a Character Shape (SFCC c)
- 104 Postnet Bar codes (SFCC |p*xxxxx-yyyy-zz*)
- 104 Ribbon Minder Enable/Disable (SFCC r E/SFCC r D)
- 104 Ribbon Minder Set Job Rate (SFCC r J nnnn E)
- 104 Ribbon Minder Worn Message (SFCC r A n)
- 105 Command Line Debug
- 106 Font Styles, Pitches, and Character Sets
- 106 Font Styles
- 106 Font Pitches
- 106 Character Sets
- 106 Extended Character Sets
- 106 Form Length
- 107 Plot Mode Graphic Densities
- 107 Enhancements
- 107 High Vertical Density Plot Mode Graphics
- 108 Chapter 5.Proprinter Emulation
- 108 Introduction
- 108 Differences from proprinter
- 108 Proprinter Control Codes
- 111 Command Directory
- 112 Escape Sequences
- 119 Proprinter Dot Graphics
- 122 Chapter 6.Epson FX286-e Emulation
- 122 Introduction
- 122 Conventions Used in this Chapter
- 123 Print Mode Combinations
- 124 Functional Differences
- 125 Additional Escape Sequences
- 125 Unsupported Escape Sequences
- 126 FX-286e Control Codes
- 129 FX-286e Escape Sequence DIRECTORY
- 131 FX-286e Escape Sequence GROUPINGS
- 132 Margins
- 134 Line Spacing
- 135 Character Spacing
- 138 Paper Movement
- 139 Print Position
- 141 Print Modes
- 145 Special Character Printing
- 149 Miscellaneous Commands
- 150 FX-286e Dot Graphics
- 150 Specifying Graphics Line Length
- 151 Image Data Bytes
- 151 Graphics Programming Example
- 151 Printed Results of Sample Program
- 152 FX-286e Dot Graphics Control Sequences
- 155 Chapter 7.DEC LG / Compaq LG Plus Emulation
- 155 Control Code Definitions
- 158 Commands
- 195 Chapter 8.PPL3 Plus Emulation
- 195 INTRODUCTION
- 195 General Considerations
- 195 Coded Characters
- 196 7-Bit Versus 8-Bit Environments
- 198 Printable Characters
- 199 CONTROL CODES
- 199 Introduction
- 199 C0 Control Characters
- 201 C1 Control Characters
- 203 SPECIAL CHARACTER PROCESSING
- 203 Hex 7F
- 203 Hex A
- 203 Hex FF
- 204 Special Character Parsing
- 205 ESCAPE SEQUENCE / control function syntax
- 205 Escape Sequence Syntax
- 205 Control Sequence Syntax
- 206 Parameter Values Within Control Sequences
- 207 COMMAND DIRECTORY
- 209 COMMAND DICTIONARY
- 251 PAGE COORDINATE SYSTEM
- 251 Coordinate System Models
- 252 Character Cell Model
- 252 Point Model
- 252 Point Model Has Precedence
- 252 Origin and Extent
- 252 Origin
- 253 Printable Area
- 253 Positioning and Movement
- 254 Horizontal Advance Increments
- 254 Fixed HAI
- 256 SIXEL GRAPHICS
- 256 Terminology and Concepts
- 257 General Sixel Graphics Operation
- 258 Sixel Graphics Commands
- 261 Appendix A. Using the Hex Dump
- 262 Appendix B. Font Print Samples
- 265 Appendix C. Postnet Bar codes
- 265 Entering and Exiting POSTNET Bar Codes
- 265 Selecting POSTNET Style Bar Codes
- 268 Appendix D. Description of Strapping Options
- 269 General Printer Options Definitions
- 270 Legacy Parallel Software Strap Definitions
- 271 Emulation Option descriptions
- 275 Appendix E. DSC Code Charts
- 310 Index