Lifetime Expectancy. Puls Dimension CP Series, DIMENSION CP20.248, CP20.248

CP-Series

CP20.248

24V, 20A, 480W, S INGLE P HASE

16.

L

IFETIME

E

XPECTANCY

The Lifetime expectancy shown in the table indicates the minimum operating hours (service life) and is determined by the lifetime expectancy of the built-in electrolytic capacitors. Lifetime expectancy is specified in operational hours and is calculated according to the capacitor’s manufacturer spec ification. The manufacturer of the electrolytic capacitors only guarantees a maximum life of up to 15 years

(131 400h). Any number exceeding this value is a calculated theoretical lifetime which can be used to compare devices.

Lifetime expectancy

AC 100V

40 000h

111 000h

23 000h

113 000h

313 000h

66 000h

AC 120V

51 000h

130 000h

33 000h

145 000h

368 000h

93 000h

AC 230V

88 000h

157 000h

63 000h

248 000h

443 000h

178 000h

At 24V, 20A and 40°C

At 24V, 10A and 40°C

At 24V, 24A and 40°C

At 24V, 20A and 25°C

At 24V, 10A and 25°C

At 24V, 24A and 25°C

17.

MTBF

MTBF stands for M ean T ime B etween F ailure, which is calculated according to statistical device failures, and indicates reliability of a device. It is the statistical representation of the likelihood of a unit to fail and does not necessarily represent the life of a product.

The MTBF figure is a statistical representation of the likelihood of a device to fail. A MTBF figure of e.g. 1 000 000h means that statistically one unit will fail every 100 hours if 10 000 units are installed in the field. However, it cannot be determined if the failed unit has been running for 50 000h or only for 100h.

For these types of units the MTTF ( M ean T ime T o F ailure) value is the same value as the MTBF value.

MTBF SN 29500, IEC 61709

MTBF MIL HDBK 217F

AC 100V

T.B.D.

T.B.D.

T.B.D.

T.B.D.

T.B.D.

T.B.D.

AC 120V

T.B.D.

T.B.D.

T.B.D.

T.B.D.

T.B.D.

T.B.D.

AC 230V

T.B.D.

T.B.D.

T.B.D.

T.B.D.

T.B.D.

T.B.D.

At 24V, 20A and 40°C

At 24V, 20A and 25°C

At 24V, 20A and 40°C;

Ground Benign GB40

At 24V, 20A and 25°C;

Ground Benign GB25

At 24V, 20A and 40°C;

Ground Fixed GF40

At 24V, 20A and 25°C;

Ground Fixed GF25

May 2020 / Rev 0.1 DS-CP20.248-EN All parameters are typical values specified 230Vac, 50Hz input voltage, 24V, 20A output load,

25°C ambient and after a 5 minutes run-in time unless otherwise noted. www.pulspower.com Phone +49 89 9278 0 Germany

17/33

CP20.248

24V, 20A, 480W, S INGLE P HASE CP-Series

18.

EMC

The EMC behavior of the device is designed for applications in industrial environment as well as in residential, commercial and light industry environments.

The device complies with EN 61000-6-1, EN 61000-6-2, EN 61000-6-3, EN 61000-6-4, EN 61000-3-2 and EN 61000-3-3.

The device complies with FCC Part 15 rules. Operation is subjected to following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Without additional measures to reduce the conducted emissions on the output (e.g. by using a filter), the device is not suited to supply a local DC power network in residential, commercial and light-industrial environments. No restrictions apply for local DC power networks in industrial environments.

EMC Immunity

Electrostatic discharge

Electromagnetic RF field

Fast transients (Burst)

Surge voltage on input

Surge voltage on output

Conducted disturbance

Mains voltage dips

Voltage interruptions

Powerful transients

Power lines and housing

EN 61000-4-2 Contact discharge

Air discharge

EN 61000-4-3

EN 61000-4-4

EN 61000-4-5

EN 61000-4-5

EN 61000-4-6

EN 61000-4-11

80MHz-2.7GHz

2.7-6GHz

Input lines

Output lines

L → N

N → PE

L → PE

+ → -

+ → PE

- → PE

0.15-80MHz

0% of 100Vac

40% of 100Vac

70% of 100Vac

0% of 120Vac

40% of 120Vac

70% of 120Vac

0% of 200Vac

40% of 200Vac

70% of 200Vac

EN 61000-4-11

VDE 0160

0V

Over entire load range

8kV

15kV

20V/m

10V/m

4kV

2kV

2kV

4kV

4kV

1kV

2kV

2kV

10V

0Vac, 20ms

40Vac, 200ms

70Vac, 500ms

0Vac, 20ms

48Vac, 200ms

84Vac, 500ms

0Vac, 20ms

80Vac, 200ms

140Vac, 500ms

5000ms

750V, 0.3ms

Criterion A

Criterion A

Criterion A

Criterion A

Criterion A

Criterion A

Criterion A

Criterion A

Criterion A

Criterion A

Criterion A

Criterion A

Criterion A

Criterion A

Criterion C

Criterion A

Criterion A

Criterion C

Criterion A

Criterion A

Criterion A

Criterion A

Criterion C

Criterion A

EMC Immunity Signal and communication lines

Fast transients (Burst)

Surge voltage

EN 61000-4-4

EN 61000-4-5

Signals with coupling clamp

DC OK, Alarm contact → PE

2kV

1kV

Criterion A

Criterion A

Performance criterions:

A: Device shows normal operation behavior within the defined limits.

C: Temporary loss of function is possible. The device may shut-down and restarts by itself. No damage or hazards for the device will occur.

May 2020 / Rev 0.1 DS-CP20.248-EN All parameters are typical values specified 230Vac, 50Hz input voltage, 24V, 20A output load,

25°C ambient and after a 5 minutes run-in time unless otherwise noted. www.pulspower.com Phone +49 89 9278 0 Germany

18/33

CP-Series

EMC Emission

Conducted emission input lines

Conducted emission output lines

Radiated emission

Harmonic input current

Voltage fluctuations, flicker

EN 55011, EN 55032, FCC Part 15, CISPR 11, CISPR

32

IEC/CISPR 16-1-2, IEC/CISPR 16-2-1

EN 55011, EN 55032, CISPR 11, CISPR 32

EN 61000-3-2 - Class A equipment

EN 61000-3-2 - Class C equipment

EN 61000-3-3

Switching Frequencies

PFC converter

Main converter

Auxiliary converter

Microcontroller

100kHz

80kHz to 140kHz

60kHz

8MHz, 8MHz, 32MHz

CP20.248

24V, 20A, 480W, S INGLE P HASE

Class B

Limits for local DC power networks not fulfilled.

Class B

Fulfilled

Fulfilled in the load range from 8 to 24A

Fulfilled, tested with non-pulsing constant current loads.

Fixed frequency

Output load dependent

Fixed frequency

The device utilize in total 3 microcontrollers

May 2020 / Rev 0.1 DS-CP20.248-EN All parameters are typical values specified 230Vac, 50Hz input voltage, 24V, 20A output load,

25°C ambient and after a 5 minutes run-in time unless otherwise noted. www.pulspower.com Phone +49 89 9278 0 Germany

19/33