Specifications of Options and Peripheral Devices. YASKAWA Varispeed f7

Specifications of Options and Peripheral Devices

Specifications of Options and Peripheral Devices

The following options and peripheral devices can be used for the Inverter. Select them according to the application.

Table 9.4 Options and Peripheral Devices

Purpose

Protect Inverter wiring

Prevents burning when a Braking Resistor is used.

Contains switching surge

Isolates I/O signals

Improve the input power factor of the

Inverter

Name

MCCB or Ground

Fault Interrupter

*1

Magnetic

Contactor

Surge Absorber

Isolator

DC Reactor

AC Reactor

Input Noise Filter

Model (Code)

NF †

SC series

DCR2†

DGP †

UZDA†

UZBA†

LNFD†

FN†

Descriptions

Always connect a breaker to the power supply line to protect Inverter wiring. Use a ground fault interrupter suitable for high frequencies.

Install to prevent the braking resistor from burning out when one is used. Always attach a surge absorber to the coil.

Absorbs surge from the magnetic contactor and control relays. Connect surge absorbers to all magnetic contactors and relays near the Inverter.

Isolates the I/O signals of the Inverter and is effective against inductive noise.

Used to improve the input power factor of the Inverter. All

Inverters of 22 kW or higher contain built-in DC reactors.

These are optional for Inverters of 18.5 kW or less. Install

DC and AC reactors for applications with a large power supply capacity (600 kVA or higher).

Reduces noise coming into the Inverter from the power supply line and to reduce noise flowing from the Inverter into the power supply line. Connect as close to the

Inverter as possible.

Power supply

Molded-case circuit breaker or ground fault interrupter

Magnetic contactor (MC)

AC reactor for power factor improvement

Zero phase reactor

Braking resistor

Reduce the affects of radio and control device noise

Finemet zerophase reactor to reduce radio noise

*2

F6045GB

(FIL001098)

F11080GB

(FIL001097)

Reduces noise from the line that sneaks into the Inverter input power system. Insert as close to the Inverter as possible.

Can be use on both the input side and output side.

Input noise filter

F200160BP

(300-001-041) Inverter

Enable stopping the machine in a set time

Operates the Inverter externally

Output Noise Filter

Braking Resistor

Braking Resistor

Unit

Braking Unit

VS Operator

(small plastic

Operator)

VS Operator

(Standard steelplate Operator)

LF†

ERF-150WJ

(R00 ††††

LKEB†

CDBR†

JVOP-95•

(73041-0905X-

JVOP-96•

†

†

††

)

(75600-K ††† 0)

(72600-R ††† 0)

(73041-0906X-

†

† )

)

Reduces noise generated by the Inverter. Connect as close to the Inverter as possible.

Consumes the regenerative motor energy with a resistor to reduce deceleration time (use rate: 3% ED).

Consumes the regenerative motor energy with a resistor to reduce deceleration time (use rate: 10% ED).

Used with a Braking Resistor Unit to reduce the deceleration time of the motor.

Allows frequency reference settings and ON/OFF operation control to be performed by analog references from a remote location (50 m max.).

Frequency counter specifications: 60/120 Hz, 90/180Hz

Allows frequency reference settings and ON/OFF operation control to be performed by analog references from a remote location (50 m max.).

Frequency counter specifications: 75 Hz, 150 Hz, 220 Hz

Varispeed F7

Ground

Output noise filter

Ground

DC reactor for power factor improvement

Zero phase reactor

Motor

Digital Operator

Connection Cable

1 m cable: (72616-

WV001)

3 m cable: (72616-

WV003)

Extension cable to use a Digital Operator remotely.

Cable length: 1 m or 3 m

Controls an Inverter system

Provides Inverter momentary power loss recovery time

VS System Module

Momentary Power

Loss Recovery

Unit

JGSM†

Frequency Meter DCF-6A

Frequency Setter RV30YN20S (2 k Ω )

Frequency Setter

Knob

P00 † 0

(73600-P00

CM-3S

† 0)

A system controller that can be match to the automatic control system to produce an optimum system configuration.

Handles momentary power losses for the control power supply for models 11 kW or less (maintains power for

2 s).

Set/monitor frequencies and voltages externally.

Devices to set or monitor frequencies externally.

Output Voltmeter SCF-12NH

Measures the output voltage externally and designed for use with a PWM Inverter.

Correct frequency reference input, frequency meter, ammeter scales

Variable Resistor

Board for Frequency Reference

Frequency Meter

Scale Correction

Resistor

2 k Ω

20 k

(ETX003270)

Ω (ETX003120)

(RH000850)

Connected to the control circuit terminals to input a frequency reference.

Calibrates the scale of frequency meters and ammeters.

* 1. Use a ground fault interrupter with a current sensitivity of 200 mA minimum and an operating time of 0.1 s minimum to prevent operating errors. The interrupter must be suitable for high-frequency operation.

Example:NV series by Mitsubishi Electric Corporation (manufactured in or after 1988)

EG, SG series by Fuji Electric Co., Ltd. (manufactured in or after 1984)

* 2. The Finemet Zero-phase Reactor is manufactured by Hitachi Metals, Ltd.

9-

5

9

-6

Built-in

(connect to connector)

Type

The following option boards are available

Table 9.5 Option Boards

Name

Code Number

Function

Analog Reference Board

AI-14U

73600-

C001X

Enables high-precision, high-resolution setting of analog speed references.

• Input signal ranges: 0 to 10 V (20 k Ω ), 1 channel

4 to 20 mA (250 Ω ), 1 channel

• Input resolution: 14-bit (1/16384)

Speed

(Frequency)

Reference

Option

Boards

Analog Reference Board

AI-14B

Digital Reference Board

DI-08

Digital Reference Board

DI-16H2

Analog Monitor Board

AO-08

Monitoring

Option

Boards

Analog Monitor Board

AO-12

Digital Output Board

DO 08

73600-

C002X

73600-

C003X

73600-

C016X

73600-

D001X

73600-

D002X

73600-

D004X

Enables high-precision, high-resolution setting of analog speed references.

• Input signal ranges: 0 to ±10 V (20 k Ω )

4 to 20 mA (500 Ω ), 3 channels

• Input resolution: 13-bit + sign (1/8192)

Enables 8-bit digital setting of speed references.

• Input signal: 8-bit binary

2-digit BCD + sign signal + set signal

• Input voltage: +24 V (isolated)

• Input current: 8 mA

Enables 16-bit digital setting of speed references.

• Input signal: 16-bit binary

4-digit BCD + sign signal + set signal

• Input voltage: +24 V (isolated)

• Input current: 8 mA

With 16-bit/12-bit switch.

Converts analog signals to monitor the Inverter's output status

(output frequency, output current, etc.) to absolute values and outputs them.

• Output resolution: 8 bits (1/256)

• Output voltage: 0 to +10 V (not insulated)

• Output channels: 2 channels

Output analog signals to monitor the Inverter's output status

(output frequency, output current, etc.).

• Output resolution: 11 bits (1/2048) + sign

• Output voltage: -10 to +10 V (not insulated)

• Output channels: 2 channels

Outputs isolated digital signals to monitor the Inverters operating status (alarm signals, zero-speed detection, etc.)

Output form: Photocoupler output, 6 channels

(48 V, 50 mA max.)

Relay contact outputs, 2 channels

(250 VAC: 1 A max., 30VDC: 1 A max.)

2C-Relay

Output Board

DO 02C

73600-

D007X

Provides two multi-function outputs (DPDT relay contacts) in addition to those provided by the Inverter.

PG

Speed

Control

Boards

PG A2

73600-

A012X

Used for V/f with PG control. Speed feedback is performed using the PG attached to the motor to compensate for speed fluctuations caused by slipping.

• A-phase pulse (single pulse) input (voltage, complementary, open-collector input)

• Maximum input frequency: 32767 Hz

• Pulse monitor output: +12 V, 20 mA

(PG power supply output: +12 V, 200 mA max.)

Document

Number

TOE-C736-

30.13

TOE-C736-

30.14

TOE-C736-

30.15

TOE-C736-

40.7

TOE-C736-

30.21

TOE-C736-

30.22

TOE-C736-

30.24

TOE-C736-

40.8

TOE-C736-

40.1

Specifications of Options and Peripheral Devices

(concon-

Type

Built-in nect to nector)

PG

Speed

Control

Boards

Name

PG

PG

-

-

B2

D2

PG-X2

Built-in

(connected to connector)

Communications

Option

Boards

CANopen

Communications Interface Board

SI-S

CC-Link

Communications Interface Board

SI-C

L ON W ORKS

Communications Interface Board

SI-J

L ON W ORKS

Communications Interface Board

SI-W1

DeviceNet

Communications Interface Board

SI-N1

ProfiBus-DP

Communications Interface Board

SI-P1

InterBus-S

Communications Interface Board

SI-R

Table 9.5 Option Boards (Continued)

Code Number

Function

73600-

A013X

• Used for V/f control with PG and flux vector control.

• A-, B-phase input (complimentary input)

• Maximum input frequency: 32767 Hz

• Pulse monitor output: Open-collector

(PG power supply output: +12 V, 200 mA max.)

73600-

A014X

73600-

A015X

• Differential input.

• A-phase pulse (differential pulse) input, for V/f control

• Maximum input frequency: 300 kHz

• Input: Conforms to RS-422

• Pulse monitor output: RS-422

(PG power supply output: +5 or +12 V, 200 mA max.)

• A-, B-, Z-phase pulse (differential pulse) input

• Maximum input frequency: 300 kHz

• Input: Conforms to RS-422

• Pulse monitor output: RS-422

(PG power supply output: +5 or +12 V, 200 mA max.)

73600-

C021X

Used to communicate with an Inverter from a host computer using DeviceNet communications to start/stop Inverter operation, read/set parameters, and read/set monitor constants (output frequencies, output currents, etc.).

73600-

C033X

*

*

73600-

C032X

73600-

C035X

73600-

C034X

Used to communicate with an Inverter from a host computer using ProfiBus-DP communications to start/stop Inverter operation, read/set parameters, and read/set monitor constants

(output frequencies, output currents, etc.).

Used to communicate with an Inverter from a host computer using InterBus-S communications to start/stop Inverter operation, read/set parameters, and read/set monitor constants (output frequencies, output currents, etc.).

Used to communicate with an Inverter from a host computer using CANopen communications to start/stop Inverter operation, read/set parameters, and read/set monitor constants (output frequencies, output currents, etc.).

Used to communicate with an Inverter from a host computer using CC-Link communications to start/stop Inverter operation, read/set parameters, and read/set monitor constants (output frequencies, output currents, etc.).

Used to communicate with an Inverter from a host computer using L ON W ORKS communications to start/stop Inverter operation, read/set parameters, and read/set monitor constants

(output frequencies, output currents, etc.).

Used to communicate with an Inverter from a host computer using L ON W ORKS communications to start/stop Inverter operation, read/set parameters, and read/set monitor constants

(output frequencies, output currents, etc.).

With Display Data Channel (DDC) function.

Document

Number

TOE-C736-

40.2

TOE-C736-

40.3

TOE-C736-

40.4

-

-

-

-

-

-

-

9-

7

9

-8

Type Name

Built-in

(connected to connector)

Communications

Option

Boards

MECHA-

TROLINK-

Communications Interface Board

SI-T

Table 9.5 Option Boards (Continued)

Code Number

Function

73600-

C030X

Used to communicate with an Inverter from a host computer using MECHATROLINK communications to start/stop

Inverter operation, read/set parameters, and read/set monitor constants (output frequencies, output currents, etc.).

Document

Number

Appendix

This chapter provides precautions for the Inverter, motor, and peripheral devices and also provides lists of constants.

Varispeed F7 Control Methods ..................................10-2

Inverter Application Precautions ................................10-6

Motor Application Precautions ...................................10-9

Conformance to UL Standard .................................. 10-11

Conformance to CE Markings..................................10-13

Wiring Examples......................................................10-22

User Constants ........................................................10-31

10