advertisement
Preliminary Guidelines 4.4 Conduits
4.4.3 Required Conduits
The types of conduits in the island are a function of the different equipment and location in the island. There are two functional conduits:
• High voltage conduits
• Low voltage conduits
The following conduits are required in the Island:
• High voltage conduits
- AC power for Islander PRIME
- Pump control from mechanical pumps to Islander PRIME
- Pump In-use signal from mechanical pumps to Islander PRIME
• Low voltage conduits
- Internet line from LAN at Office to Islander PRIME
- RS-232 communication line from TLG at office to Islander PRIME
- RS-485/422/C.L. or Tokheim
- Pulser from pumps to Islander PRIME
• Grounding
- At least 10 mm (OOO AWG) Grounding cable to pump chassis
- At least 10 mm (OOO AWG) Grounding cable to Islander PRIME pole (Connected to the external chassis grounding post)
- Grounding cable to TLG – in accordance with TLG manufacturer instructions
• Tank conduit
- TLG Probe
4.4.4 Layout
Four conduits can be inserted in Islander PRIME, each carrying specific wires (see Table 3 ).
Table 3: Conduits into Islander PRIME
2
3
No.
Conduit Type Type
1 Low voltage Pulser, TLG, LAN
High voltage
High voltage
AC power, GND, In-use
Control
Page 28 MDE-5411B ForeHB Islander PRIME Installation Manual · February 2020
4.4 Conduits Preliminary Guidelines
The following is a diagram of the conduit layout for Islander PRIME using a mechanical pump
(see
):
Figure 12: Conduit Layout for Mechanical Pump
MDE-5411B ForeHB Islander PRIME Installation Manual · February 2020 Page 29
Preliminary Guidelines 4.4 Conduits
The following is a diagram of the conduit layout for Islander PRIME using an electronic pump
(see
):
Figure 13: Conduits Layout for Electronic Pump
Page 30 MDE-5411B ForeHB Islander PRIME Installation Manual · February 2020
advertisement
Related manuals
advertisement
Table of contents
- 13 1.1 General
- 13 1.2 Solution Description
- 14 1.3 System Architecture
- 15 1.4 Manual Structure
- 15 1.5 References
- 16 1.6 Documentation Conventions
- 21 3.1 General
- 21 3.2 System Description
- 21 3.2.1 Fuel Point PLUS - Automatic Vehicle Identification
- 21 3.2.2 Remote Web Access
- 21 3.2.3 Head Office
- 22 3.2.4 Restrictions and Limits
- 22 3.2.5 Islander PRIME Capabilities for Forecourt Management
- 22 3.2.6 System Workflow
- 23 3.3 Islander PRIME Structure
- 23 3.3.1 Main Components
- 27 3.3.2 Internal Configuration
- 27 3.4 Available Configurations
- 27 3.4.1 Islander PRIME
- 28 3.4.2 Automatic Vehicle Identification
- 28 3.4.3 Dispensers
- 28 3.4.4 Barcode Reader Option
- 28 3.4.5 Insert Card Reader Option
- 28 3.4.6 HID Option
- 28 3.4.7 Cellular Modem Option
- 28 3.4.8 Receipt Printer Option
- 29 3.4.9 EMV Option
- 29 3.4.10 Communication Interfaces
- 29 3.5 Security and Protection
- 29 3.5.1 Authorization
- 29 3.5.2 Network
- 29 3.5.3 RF Network
- 30 3.5.4 Maintenance
- 30 3.6 Housing
- 31 3.7 Technical Specifications and Standards
- 31 3.7.1 Islander PRIME Technical Specifications
- 32 3.7.2 Communication and Security Standards
- 33 4.1 General
- 33 Précautions et consignes de sécurité
- 35 4.3 Station Survey
- 35 4.3.1 Station Architecture
- 36 4.3.2 Locating All Objects
- 36 4.3.3 Assigning Logical IDs
- 37 4.3.4 Connections
- 38 4.4 Conduits
- 38 4.4.1 Requirements
- 39 4.4.2 Protective Plate
- 40 4.4.3 Required Conduits
- 40 4.4.4 Layout
- 43 4.4.5 Installation
- 43 4.4.6 Sealing
- 43 4.5 Cable Insertion
- 44 4.5.1 Cable Types
- 44 4.5.2 Cable Routing
- 44 4.6 Power Setup
- 45 4.6.1 Connection Diagram
- 45 4.6.2 Power Supply Setup
- 46 4.6.3 Connecting the Power Equipment
- 46 4.6.4 Grounding
- 46 4.7 Wiring the Peripherals
- 46 4.7.1 Pump Wiring
- 47 4.7.2 TLG Wiring
- 49 5.1 General
- 49 5.2 Installation Guidelines
- 49 5.2.1 Precautions and Safety Notes
- 49 5.2.2 Safety Distances
- 50 5.3 Installing the Pedestal Base
- 51 5.3.1 Installation Procedure
- 51 5.3.2 Preliminary Setup
- 51 5.3.3 Assembly Parts
- 52 5.3.4 Base Plate
- 53 5.3.5 Pedestal
- 54 5.3.6 Sealing Conduits
- 54 5.4 Installing Options
- 55 5.4.1 Barcode Reader Installation
- 57 5.4.2 HID Reader Installation
- 60 5.4.3 Insertion Card Reader Installation
- 62 5.4.4 Cellular Modem Installation
- 64 5.4.5 G2 Panel Printer Installation
- 66 5.5 Installing Communication Interfaces
- 66 5.5.1 Adding Communication Interface Blades to the Pedestal
- 69 5.5.2 Wiring Requirements
- 70 5.5.3 Mechanical Dispenser Connections
- 72 5.5.4 Pulser Connections
- 74 5.5.5 Electronic Dispenser Connections
- 79 5.6 Post-Installation Checklist
- 80 5.7 Islander PRIME Setup
- 81 6.1 General
- 82 6.2 Home Page
- 83 6.3 Setup
- 83 6.3.1 Minimal Setup
- 84 6.3.2 General Setup
- 85 6.3.3 OrIC Config
- 87 6.3.4 Log Level
- 88 6.3.5 Save
- 90 6.4 Software Upload
- 93 7.1 General
- 93 7.2 OrPAY1000 and Islander PRIME
- 93 7.3 Magnetic Card Reader
- 94 7.4 Printer
- 97 8.1 General
- 97 8.2 Islander PRIME
- 97 8.2.1 System Down
- 98 8.2.2 Mechanical Pump Does Not Fuel
- 100 8.2.3 No Control Over Fueling
- 100 8.3 OrPAY
- 102 8.4 Printer
- 104 8.5 Communication
- 106 8.6 FuelPoint