advertisement
Maintenance 7.4 Printer
7.4 Printer
Due to the harsh environment of the homebase station, the printer should be cleaned periodically.
Note: Clean the printer front panel with a damp cloth only. DO NOT use any solvents such as thinner or benzene to clean the printer front panel.
The following describes the cleaning procedures for the thermal printer head in the printer.
The cleaning is performed with the printer cleaning card. The printer cleaning card is provided in a protective package to prevent dryness.
The cleaning procedure shall be performed whenever ink is faded on a receipt.
Note: The cleaning procedure must be done quickly as the substance in the cleaning card evaporates over a short period of time.
To clean the thermal printer head, proceed as follows:
1 Turn on the printer.
2 Insert paper in the printer slot, and make sure that the printer guillotine cuts the paper protruding from the printer.
Note: This procedure ensures that the guillotine will not cut the cleaning card.
3
Press the green paper-lock lever and pull out the paper from the printer (see Figure 70 ).
Figure 70: Paper Lock Lever
Page 82
4 Remove the cleaning card from its packaging.
5 Insert the cleaning card manually into the printer paper slot.
6 Press the green paper-lock lever back to its initial position.
MDE-5411B ForeHB Islander PRIME Installation Manual · February 2020
7.4 Printer Maintenance
7 Push and pull the cleaning card so that the printer head is cleaned.
8 Verify that the cleaning card has been removed from the printer guillotine without being affected.
9 Verify that the cleaning card rolls out from the paper slot.
10 Pull the cleaning card gently, and repeat steps 5 to 9 with the same cleaning card now tilted to the left.
11 Repeat the above several times in order to obtain the best cleaning results.
12 Stop when the cleaning card is dry.
13 Press the green paper-lock lever and insert thermal paper in the printer from the paper roll.
14 Press the green paper-lock lever back.
15 Print a receipt with at least ten rows of text.
16 Check readability and verify the text font is clear.
Note: If readability is still poor, repeat the cleaning procedure with a new cleaning card.
MDE-5411B ForeHB Islander PRIME Installation Manual · February 2020 Page 83
Maintenance 7.4 Printer
This page is intentionally blank.
Page 84 MDE-5411B ForeHB Islander PRIME Installation Manual · February 2020
advertisement
Related manuals
advertisement
Table of contents
- 13 1.1 General
- 13 1.2 Solution Description
- 14 1.3 System Architecture
- 15 1.4 Manual Structure
- 15 1.5 References
- 16 1.6 Documentation Conventions
- 21 3.1 General
- 21 3.2 System Description
- 21 3.2.1 Fuel Point PLUS - Automatic Vehicle Identification
- 21 3.2.2 Remote Web Access
- 21 3.2.3 Head Office
- 22 3.2.4 Restrictions and Limits
- 22 3.2.5 Islander PRIME Capabilities for Forecourt Management
- 22 3.2.6 System Workflow
- 23 3.3 Islander PRIME Structure
- 23 3.3.1 Main Components
- 27 3.3.2 Internal Configuration
- 27 3.4 Available Configurations
- 27 3.4.1 Islander PRIME
- 28 3.4.2 Automatic Vehicle Identification
- 28 3.4.3 Dispensers
- 28 3.4.4 Barcode Reader Option
- 28 3.4.5 Insert Card Reader Option
- 28 3.4.6 HID Option
- 28 3.4.7 Cellular Modem Option
- 28 3.4.8 Receipt Printer Option
- 29 3.4.9 EMV Option
- 29 3.4.10 Communication Interfaces
- 29 3.5 Security and Protection
- 29 3.5.1 Authorization
- 29 3.5.2 Network
- 29 3.5.3 RF Network
- 30 3.5.4 Maintenance
- 30 3.6 Housing
- 31 3.7 Technical Specifications and Standards
- 31 3.7.1 Islander PRIME Technical Specifications
- 32 3.7.2 Communication and Security Standards
- 33 4.1 General
- 33 Précautions et consignes de sécurité
- 35 4.3 Station Survey
- 35 4.3.1 Station Architecture
- 36 4.3.2 Locating All Objects
- 36 4.3.3 Assigning Logical IDs
- 37 4.3.4 Connections
- 38 4.4 Conduits
- 38 4.4.1 Requirements
- 39 4.4.2 Protective Plate
- 40 4.4.3 Required Conduits
- 40 4.4.4 Layout
- 43 4.4.5 Installation
- 43 4.4.6 Sealing
- 43 4.5 Cable Insertion
- 44 4.5.1 Cable Types
- 44 4.5.2 Cable Routing
- 44 4.6 Power Setup
- 45 4.6.1 Connection Diagram
- 45 4.6.2 Power Supply Setup
- 46 4.6.3 Connecting the Power Equipment
- 46 4.6.4 Grounding
- 46 4.7 Wiring the Peripherals
- 46 4.7.1 Pump Wiring
- 47 4.7.2 TLG Wiring
- 49 5.1 General
- 49 5.2 Installation Guidelines
- 49 5.2.1 Precautions and Safety Notes
- 49 5.2.2 Safety Distances
- 50 5.3 Installing the Pedestal Base
- 51 5.3.1 Installation Procedure
- 51 5.3.2 Preliminary Setup
- 51 5.3.3 Assembly Parts
- 52 5.3.4 Base Plate
- 53 5.3.5 Pedestal
- 54 5.3.6 Sealing Conduits
- 54 5.4 Installing Options
- 55 5.4.1 Barcode Reader Installation
- 57 5.4.2 HID Reader Installation
- 60 5.4.3 Insertion Card Reader Installation
- 62 5.4.4 Cellular Modem Installation
- 64 5.4.5 G2 Panel Printer Installation
- 66 5.5 Installing Communication Interfaces
- 66 5.5.1 Adding Communication Interface Blades to the Pedestal
- 69 5.5.2 Wiring Requirements
- 70 5.5.3 Mechanical Dispenser Connections
- 72 5.5.4 Pulser Connections
- 74 5.5.5 Electronic Dispenser Connections
- 79 5.6 Post-Installation Checklist
- 80 5.7 Islander PRIME Setup
- 81 6.1 General
- 82 6.2 Home Page
- 83 6.3 Setup
- 83 6.3.1 Minimal Setup
- 84 6.3.2 General Setup
- 85 6.3.3 OrIC Config
- 87 6.3.4 Log Level
- 88 6.3.5 Save
- 90 6.4 Software Upload
- 93 7.1 General
- 93 7.2 OrPAY1000 and Islander PRIME
- 93 7.3 Magnetic Card Reader
- 94 7.4 Printer
- 97 8.1 General
- 97 8.2 Islander PRIME
- 97 8.2.1 System Down
- 98 8.2.2 Mechanical Pump Does Not Fuel
- 100 8.2.3 No Control Over Fueling
- 100 8.3 OrPAY
- 102 8.4 Printer
- 104 8.5 Communication
- 106 8.6 FuelPoint