advertisement
7.1 General
7 – Maintenance
Maintenance
7.1 General
Islander PRIME itself as a standalone unit should be cleaned periodically at short intervals, due to the harsh environment of the homebase station where it operates.
7.2 OrPAY1000 and Islander PRIME
The following instructions are valid for the OrPAY1000 front panel and the Islander PRIME pedestal.
• Clean the OrPAY1000 front plastic panel with a lightly moistened cloth with WD-40 or any other similar lubricant.
• Clean the pedestal metallic enclosure using a damp cloth and cleaning spray.
CAUTION
Caution:
• DO NOT use any solvents such as thinner or benzene.
• Do not pressure wash the pedestal.
Mise en garde:
• NE PAS utiliser de solvants tels qu'un diluant ou du benzène.
• Ne pas utiliser un lavage sous pression pour nettoyer le piédestal.
7.3 Magnetic Card Reader
The Card Reader should be cleaned periodically, preferably once every two weeks, in order to ensure proper operation. The purpose of cleaning is to remove any dust that may harm the reader and consequently prevent the completion of a sale.
To clean the magnetic card reader, proceed as follows:
1 Remove the cleaning card from its packing.
2 Insert the cleaning card all the way in the reader, and then pull it out slowly.
3 Perform steps 1 and 2 several times until the card is dry.
4 Insert any magnetic card and verify that its stored data is read by the magnetic card reader.
MDE-5411B ForeHB Islander PRIME Installation Manual · February 2020 Page 81
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 13 1.1 General
- 13 1.2 Solution Description
- 14 1.3 System Architecture
- 15 1.4 Manual Structure
- 15 1.5 References
- 16 1.6 Documentation Conventions
- 21 3.1 General
- 21 3.2 System Description
- 21 3.2.1 Fuel Point PLUS - Automatic Vehicle Identification
- 21 3.2.2 Remote Web Access
- 21 3.2.3 Head Office
- 22 3.2.4 Restrictions and Limits
- 22 3.2.5 Islander PRIME Capabilities for Forecourt Management
- 22 3.2.6 System Workflow
- 23 3.3 Islander PRIME Structure
- 23 3.3.1 Main Components
- 27 3.3.2 Internal Configuration
- 27 3.4 Available Configurations
- 27 3.4.1 Islander PRIME
- 28 3.4.2 Automatic Vehicle Identification
- 28 3.4.3 Dispensers
- 28 3.4.4 Barcode Reader Option
- 28 3.4.5 Insert Card Reader Option
- 28 3.4.6 HID Option
- 28 3.4.7 Cellular Modem Option
- 28 3.4.8 Receipt Printer Option
- 29 3.4.9 EMV Option
- 29 3.4.10 Communication Interfaces
- 29 3.5 Security and Protection
- 29 3.5.1 Authorization
- 29 3.5.2 Network
- 29 3.5.3 RF Network
- 30 3.5.4 Maintenance
- 30 3.6 Housing
- 31 3.7 Technical Specifications and Standards
- 31 3.7.1 Islander PRIME Technical Specifications
- 32 3.7.2 Communication and Security Standards
- 33 4.1 General
- 33 Précautions et consignes de sécurité
- 35 4.3 Station Survey
- 35 4.3.1 Station Architecture
- 36 4.3.2 Locating All Objects
- 36 4.3.3 Assigning Logical IDs
- 37 4.3.4 Connections
- 38 4.4 Conduits
- 38 4.4.1 Requirements
- 39 4.4.2 Protective Plate
- 40 4.4.3 Required Conduits
- 40 4.4.4 Layout
- 43 4.4.5 Installation
- 43 4.4.6 Sealing
- 43 4.5 Cable Insertion
- 44 4.5.1 Cable Types
- 44 4.5.2 Cable Routing
- 44 4.6 Power Setup
- 45 4.6.1 Connection Diagram
- 45 4.6.2 Power Supply Setup
- 46 4.6.3 Connecting the Power Equipment
- 46 4.6.4 Grounding
- 46 4.7 Wiring the Peripherals
- 46 4.7.1 Pump Wiring
- 47 4.7.2 TLG Wiring
- 49 5.1 General
- 49 5.2 Installation Guidelines
- 49 5.2.1 Precautions and Safety Notes
- 49 5.2.2 Safety Distances
- 50 5.3 Installing the Pedestal Base
- 51 5.3.1 Installation Procedure
- 51 5.3.2 Preliminary Setup
- 51 5.3.3 Assembly Parts
- 52 5.3.4 Base Plate
- 53 5.3.5 Pedestal
- 54 5.3.6 Sealing Conduits
- 54 5.4 Installing Options
- 55 5.4.1 Barcode Reader Installation
- 57 5.4.2 HID Reader Installation
- 60 5.4.3 Insertion Card Reader Installation
- 62 5.4.4 Cellular Modem Installation
- 64 5.4.5 G2 Panel Printer Installation
- 66 5.5 Installing Communication Interfaces
- 66 5.5.1 Adding Communication Interface Blades to the Pedestal
- 69 5.5.2 Wiring Requirements
- 70 5.5.3 Mechanical Dispenser Connections
- 72 5.5.4 Pulser Connections
- 74 5.5.5 Electronic Dispenser Connections
- 79 5.6 Post-Installation Checklist
- 80 5.7 Islander PRIME Setup
- 81 6.1 General
- 82 6.2 Home Page
- 83 6.3 Setup
- 83 6.3.1 Minimal Setup
- 84 6.3.2 General Setup
- 85 6.3.3 OrIC Config
- 87 6.3.4 Log Level
- 88 6.3.5 Save
- 90 6.4 Software Upload
- 93 7.1 General
- 93 7.2 OrPAY1000 and Islander PRIME
- 93 7.3 Magnetic Card Reader
- 94 7.4 Printer
- 97 8.1 General
- 97 8.2 Islander PRIME
- 97 8.2.1 System Down
- 98 8.2.2 Mechanical Pump Does Not Fuel
- 100 8.2.3 No Control Over Fueling
- 100 8.3 OrPAY
- 102 8.4 Printer
- 104 8.5 Communication
- 106 8.6 FuelPoint