5.CONFIGURING THE ADSL NETWORK FOR ETHERNET OVER ATM (RFC1483). HON HAI PRECISION IND. MCLT60093

PCI Full Rate ADSL Modem Driver Installation

A2RAI-081699

Windows 95

§ ITeX ADSL Network Modem (Apollo 2 - 8MB/s)

§ ATM Call Manager à ITeX ADSL Network Modem (Apollo 2 - 8MB/s)

§ TCP/IP

Click "Cancel" to close the Network window.

4.2 Windows NT 4.0

Double-click the Network icon. The network dialog window appears. In the Network dialog window, select the Configuration tab.

Verify the following network components were installed in the:

Adapters Tab

§ ITeX ADSL Network Modem (Apollo 2 – 8Mb/s)

Protocols Tab

§ ADSL Management and Monitor Interface

§ TCP/IP Protocol

Click Ok to close the Network dialog window.

5.CONFIGURING THE ADSL NETWORK FOR ETHERNET OVER ATM (RFC1483)

5.1 Windows 95 (OSR1/OSR2) and Windows 98 (1 st and 2 nd Edition)

From the Start menu, select settings and open the control panel. Double click on the Network icon. The Network window will appear.

Date Printed: 12/20/99 Page 14

PCI Full Rate ADSL Modem Driver Installation

A2RAI-081699

Select the Configuration Tab and scroll through the installed network component list.

For Windows 98 2 nd

For Windows 98 1 s t

Edition, highlight the TCP/IP à ITeX RFC1483 Ethernet Adapter component.

Edition, highlight the TCP/IP à ITeX ADSL Network Modem (Ambit PCI -

8Mbps). For Windows 95, highlight "TCP/IP". Click "Properties.” The TCP/IP Properties window will appear.

To setup the IP Address, select the IP Address tab and then select the "Specify an IP address" option. Enter the IP Address and Subnet Mask settings.

Date Printed: 12/20/99 Page 15

PCI Full Rate ADSL Modem Driver Installation

A2RAI-081699

To setup a new gateway, enter the setting in the new gateway section and click "Add.” This will add the setting into the installed gateways.

To configure the Domain Name Server, simply select the Enable DNS option. Enter the Host and

Domain settings. Enter the DNS Server search order and click "Add.”

Once all the TCP/IP properties have been set, click "OK" to return to the Network window.

Date Printed: 12/20/99 Page 16

PCI Full Rate ADSL Modem Driver Installation

A2RAI-081699

Click "OK" to close the Network window.

Click "No" when prompted "Do you want to restart your computer now?"

SETTING THE PVC VALUES FOR ETHERNET OVER ATM (RFC1483)

Windows 98 2 nd Edition

For RFC1483, the VPI and VCI have a default setting of 8 and 35 respectively. To change the values for RFC1483, follow these instructions:

Using the Modem Icon Utility to Set the PVC Values

Refer to "User's Guide to the Modem Icon Utility" for more information.

VPI

VCI

Parameter Value

0 - 255

0 - 255

Meaning

Virtual Path Identifier

Virtual Channel Identifier

Close the ITeX ADSL Test Application window and restart the computer.

Configuring the ADSL modem for RFC1483 is completed.

Windows 98 1 st Edition and Windows 95

From the Network configuration window, select "ITeX ADSL Network Modem (Apollo 2 - 8Mb/s)".

Select Properties and then select the Advanced tab. Enter the VPI and VCI values.

Date Printed: 12/20/99 Page 17

PCI Full Rate ADSL Modem Driver Installation

A2RAI-081699

5.2 Windows NT4.0

Ethernet over ATM (RFC1483)

Open the Network dialog window by double clicking My Computer->Control Panel->Network.

In the Network window, select the Adapters tab.

Scroll through the installed network components list. Highlight the "ITeX ADSL Network Modem

(Apollo 2 - 8Mbps)" and click Properties.

The TCP/IP Properties window appears.

Please check your TCP/IP configuration with your Internet service provider.

From the Network configuration window, select the "TCP/IP à ITeX ADSL Network Modem

(Ambit PCI - 8 Mb/s)" option in the configuration tab, click "Properties.” The TCP/IP Properties window will appear.

To setup the IP Address, select the IP Address tab and then select the "Specify an IP address" option. Enter the IP Address and Subnet Mask settings.

Date Printed: 12/20/99 Page 18

PCI Full Rate ADSL Modem Driver Installation

A2RAI-081699

To setup a new gateway, enter the setting in the new gateway section and click "Add.” This will add the setting into the installed gateways.

To configure the Domain Name Server, simply select the Enable DNS option. Enter the Host and

Domain settings. Enter the DNS Server Search Order and click "Add.”

Once all the TCP/IP properties have been set, click "OK" to return to the Network window.

Date Printed: 12/20/99 Page 19