Working With Files, Folders And Programs. Psion GM3WCF2011BE, 7535 Hand-Held Computer
Pubblicità
Pubblicità
7535 Hand-Held
Computer
User Manual
May 16, 2003 Part No. 8000007.A
I
SO 9001 Certified
Quality Management System
© Copyright 2003 by Psion Teklogix Inc., Mississauga, Ontario
This document and the information it contains is the property of Psion Teklogix Inc., is issued in strict confidence, and is not to be reproduced or copied, in whole or in part, except for the sole purpose of promoting the sale of Teklogix manufactured goods and services. Furthermore, this document is not to be used as a basis for design, manufacture, or sub-contract, or in any manner detrimental to the interests of Psion Teklogix Inc.
All trademarks are the property of their respective holders.
Return-To-Factory Warranty
Psion Teklogix warrants a return-to-factory warranty for a period of one year from shipment. The warranty on Psion Teklogix manufactured equipment does not extend to any product that has been tampered with, altered, or repaired by any person other than an employee of an authorized Psion Teklogix service organization. See Psion
Teklogix terms and conditions of sale for full details.
Service
When requesting service, please provide information concerning the nature of the failure and the manner in which the equipment was used when the failure occurred.
Type, model, and serial number should also be provided. Before returning any
Authorization number.
Support Services
Psion Teklogix provides a complete range of product support services to its customers. In North America, these services can be accessed through the Psion Teklogix
Helpdesk. The Helpdesk coordinates repairs and training, helps you to troubleshoot problems over the phone and arranges for technicians or engineers to come to your site. For contact information and a listing of worldwide offices, please refer to
Appendix A: Support Services And Worldwide Offices.
Disclaimer
Every effort has been made to make this material complete, accurate and up-to-date.
Teklogix Inc. reserves the right to make changes without notice and shall not be held responsible for damages resulting from reliance on the material presented in this manual.
P
ROGRAM
L
ICENSE
A
GREEMENT
Microsoft's End User License Agreement
You have acquired an item (“DEVICE”) that includes software licensed from
Microsoft Licensing Inc. or its affiliates (“MS”). Those installed software products of MS origin, as well as associated media, printed materials, and “online” or electronic documentation (“SOFTWARE”) are protected by copyright laws and international copyright treaties, as well as other intellectual property laws and treaties. The
SOFTWARE is licensed, not sold.
IF YOU DO NOT AGREE TO THIS END USER LICENSE AGREEMENT
(“EULA”), DO NOT USE THE DEVICE OR COPY THE SOFTWARE.
INSTEAD, CONTACT PSION TEKLOGIX INC IMMEDIATELY FOR
INSTRUCTIONS ON RETURN OF THE UNUSED DEVICE(S) FOR A
REFUND. ANY USE OF THE SOFTWARE, INCLUDING BUT NOT LIMITED
TO USE ON THE DEVICE, WILL CONSTITUTE YOUR AGREEMENT TO
THIS EULA (OR RATIFICATION OF ANY PREVIOUS CONSENT).
GRANT OF LICENSE. The SOFTWARE is licensed, not sold. This EULA grants you the following rights to the SOFTWARE:
• You may use the SOFTWARE only on the DEVICE.
• NOT FAULT TOLERANT. THE SOFTWARE IS NOT FAULT TOLER-
ANT. PSION TEKLOGIX INC. HAS INDEPENDENTLY DETER-
MINED HOW TO USE THE SOFTWARE IN THE DEVICE, AND MS
HAS RELIED UPON PSION TEKLOIGX INC. TO CONDUCT SUFFI-
CIENT TESTING TO DETERMINE THAT THE SOFTWARE IS SUIT-
ABLE FOR SUCH USE.
Teklogix 7535 Hand-Held Computer User Manual I
License Agreement
• NO WARRANTIES FOR THE SOFTWARE. THE SOFTWARE is provided “AS IS” and with all faults. THE ENTIRE RISK AS TO
SATISFACTORY QUALITY, PERFORMANCE, ACCURACY, AND
EFFORT (INCLUDING LACK OF NEGLIGENCE) IS WITH YOU.
ALSO, THERE IS NO WARRANTY AGAINST INTERFERENCE WITH
YOUR ENJOYMENT OF THE SOFTWARE OR AGAINST
INFRINGEMENT. IF YOU HAVE RECEIVED ANY WARRANTIES
REGARDING THE DEVICE OR THE SOFTWARE, THOSE WARRAN-
TIES DO NOT ORIGINATE FROM, AND ARE NOT BINDING ON, MS.
• Note on Java Support. The SOFTWARE may contain support for programs written in Java. Java technology is not fault tolerant and is not designed, manufactured, or intended for use or resale as online control equipment in hazardous environments requiring fail-safe performance, such as in the operation of nuclear facilities, aircraft navigation or communication systems, air traffic control, direct life support machines, or weapons systems, in which the failure of Java technology could lead directly to death, personal injury, or severe physical or environmental damage. Sun Microsystems, Inc. has contractually obligated MS to make this disclaimer.
• No Liability for Certain Damages. EXCEPT AS PROHIBITED BY LAW,
MS SHALL HAVE NO LIABILITY FOR ANY INDIRECT, SPECIAL,
CONSEQUENTIAL OR INCIDENTAL DAMAGES ARISING FROM
OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THE
SOFTWARE. THIS LIMITATION SHALL APPLY EVEN IF ANY
REMEDY FAILS OF ITS ESSENTIAL PURPOSE. IN NO EVENT
SHALL MS BE LIABLE FOR ANY AMOUNT IN EXCESS OF U.S.
TWO HUNDRED FIFTY DOLLARS (U.S.$250.00).
• Limitations on Reverse Engineering, Decompilation, and Disassembly. You may not reverse engineer, decompile, or disassemble the SOFTWARE, except and only to the extent that such activity is expressly permitted by applicable law notwithstanding this limitation.
• SOFTWARE TRANSFER ALLOWED BUT WITH RESTRICTIONS. You may permanently transfer rights under this EULA only as part of a permanent sale or transfer of the Device, and only if the recipient agrees to this
EULA. If the SOFTWARE is an upgrade, any transfer must also include all prior versions of the SOFTWARE.
II Teklogix 7535 Hand-Held Computer User Manual
License Agreement
• EXPORT RESTRICTIONS. If these licensing terms are not labeled “North
America Only Version” and the SOFTWARE is not identified as “North
America Only Version” on the SOFTWARE packaging or other written materials, then the following terms apply: Export of the Department,
Bureau of Export Administration (BXA). You agree to comply with the
EAR in the export or re-export of the SOFTWARE: (i) to any country to which the U.S. has embargoed or restricted the export of goods or services, which as of May 1999 include, but are not necessarily limited to Cuba, Iran,
Iraq, Libya, North Korea, Sudan, Syria, and the Federal Republic or Yugoslavia (including Serbia, but not Montenegro), or to any national of any such country, wherever located, who intends to transmit or transport the
SOFTWARE back to such country; (ii) to any person or entity who you know or have reason to know will utilize the SOFTWARE or portion thereof in the design, development or production of nuclear, chemical, or biological weapons; or (iii) to any person or entity who has been prohibited from participating in U.S. export transactions by any federal agency or the
U.S. government. You warrant and represent that neither the BXA nor any other U.S. federal agency has suspended, revoked or denied your export privileges. For additional information see http://www.microsoft.com/exporting/.
Teklogix 7535 Hand-Held Computer User Manual III
T
ABLE OF
C
ONTENTS
Program License Agreement
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I
Approvals And Safety Summary
. . . . . . . . . . . . . . . . . . . . . . . . . . . xi
Chapter 1: Introduction
1.1
About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.2
Text Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.3
About The 7535 Hand-Held Computer . . . . . . . . . . . . . . . . . . 5
1.3.1 Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.3.2 The 7535 Hand-Held Computer . . . . . . . . . . . . . . . . . . 7
1.3.3 The 7535 Hand-Held Safety Labels . . . . . . . . . . . . . . . . 9
Chapter 2: Unpacking & Basic Checkout
2.1
Preparing The 7535 For Operation . . . . . . . . . . . . . . . . . . . .13
2.1.1 Equipment You Need To Get Started . . . . . . . . . . . . . . .13
2.1.2 Charging The Battery . . . . . . . . . . . . . . . . . . . . . . .13
2.1.3 Attaching Carrying Accessories . . . . . . . . . . . . . . . . . .13
2.1.3.1
Attaching The Hand Strap . . . . . . . . . . . . . . . .14
2.1.3.2
Attaching The Pistol Grip . . . . . . . . . . . . . . . .15
2.2
Powering Up The 7535 And Configuring The Radio . . . . . . . . . . .16
2.2.1 Installing The Battery And Switching The 7535 On. . . . . . . .17
2.2.2 Configuring An IEEE 802.11 Radio . . . . . . . . . . . . . . . .18
2.3
Advanced NETWLAN Settings. . . . . . . . . . . . . . . . . . . . . .22
2.3.1 Preferred Networks. . . . . . . . . . . . . . . . . . . . . . . . .23
2.3.2 Advanced Network Access. . . . . . . . . . . . . . . . . . . . .23
2.3.3 Configuring WEP Keys . . . . . . . . . . . . . . . . . . . . . .24
2.4
Additional Radio Security Options . . . . . . . . . . . . . . . . . . . .28
2.5
Checking The Scanner . . . . . . . . . . . . . . . . . . . . . . . . . .29
2.6
Uploading New Applications . . . . . . . . . . . . . . . . . . . . . . .29
2.7
Calibrating The Touchscreen . . . . . . . . . . . . . . . . . . . . . . .30
Teklogix 7535 Hand-Held Computer User Manual i
Contents
2.8
Resetting The 7535 Hand-Held . . . . . . . . . . . . . . . . . . . . . 30
Chapter 3: Getting To Know Your 7535
3.1
Features Of The 7535 . . . . . . . . . . . . . . . . . . . . . . . . . . 33
3.2
The Battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
3.2.1 Battery Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
3.2.2 Removing And Installing The Battery Pack . . . . . . . . . . . 34
3.2.3 Charging The Battery . . . . . . . . . . . . . . . . . . . . . . . 35
3.3
Switching The 7535 Hand-Held On And Off . . . . . . . . . . . . . . 36
3.4
The Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
3.4.1 Modifier Keys. . . . . . . . . . . . . . . . . . . . . . . . . . . 38
3.4.1.1
Activating Modifier Keys. . . . . . . . . . . . . . . . 39
3.4.1.2
Locking Modifier Keys. . . . . . . . . . . . . . . . . 39
3.4.2 The Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
3.4.3 The 58-Key Keyboard . . . . . . . . . . . . . . . . . . . . . . 40
3.4.4 The 36-Key Keyboard . . . . . . . . . . . . . . . . . . . . . . 40
3.4.5 The Keypad Backlight . . . . . . . . . . . . . . . . . . . . . . 42
3.5
The Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
3.5.1 Adjusting The Display Backlight . . . . . . . . . . . . . . . . . 43
3.5.2 Adjusting The Contrast On Monochrome Displays . . . . . . . 43
3.5.3 Calibrating The Touchscreen . . . . . . . . . . . . . . . . . . . 44
3.6
7535 Hand-Held Computer Indicators. . . . . . . . . . . . . . . . . . 45
3.6.1 LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
3.6.1.1
Charge LEDs . . . . . . . . . . . . . . . . . . . . . . 46
3.6.1.2
Radio Traffic LEDs. . . . . . . . . . . . . . . . . . . 46
3.6.1.3
Scan LEDs . . . . . . . . . . . . . . . . . . . . . . . 47
3.6.2 Onscreen Indicators . . . . . . . . . . . . . . . . . . . . . . . . 47
3.6.3 Audio Indicators . . . . . . . . . . . . . . . . . . . . . . . . . 49
3.6.3.1
Adjusting The Beeper Volume . . . . . . . . . . . . . 49
3.7
Internal Scanners. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
3.7.1 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
3.7.2 Scanning Techniques . . . . . . . . . . . . . . . . . . . . . . . 51
3.7.3 Scan LED Indicators . . . . . . . . . . . . . . . . . . . . . . . 52
3.7.4 Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . 52
3.7.5 Operating One Dimensional (1D) Internal Laser Scanners. . . . 53
3.7.6 Operating Internal PDF Laser Scanners . . . . . . . . . . . . . 53
3.7.7 Operating Internal Two Dimensional (2D) Imager Scanners . . 53 ii Teklogix 7535 Hand-Held Computer User Manual
Contents
3.8
Connecting & Disconnecting Tethered Peripherals . . . . . . . . . . . .54
3.9
Monitoring The Battery And Maximizing Run Time . . . . . . . . . . .55
3.10 Monitoring The Network Connection. . . . . . . . . . . . . . . . . . .57
3.11 Uploading Data In A Docking Station . . . . . . . . . . . . . . . . . .57
3.12 General Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . .58
3.12.1 Caring For The Touchscreen . . . . . . . . . . . . . . . . . . . .58
3.12.2 Cleaning The 7535 . . . . . . . . . . . . . . . . . . . . . . . . .58
Chapter 4: Working With Windows CE
4.1
Navigating In Windows CE And Applications . . . . . . . . . . . . . .61
4.1.1 Navigating Using A Touchscreen And Stylus . . . . . . . . . . .61
4.1.2 Navigating Using The Keyboard. . . . . . . . . . . . . . . . . .61
4.2
Working With Files, Folders And Programs . . . . . . . . . . . . . . .62
4.3
The Startup Desktop. . . . . . . . . . . . . . . . . . . . . . . . . . . .63
4.3.1 Accessing Desktop Icons. . . . . . . . . . . . . . . . . . . . . .63
4.3.2 The Taskbar . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
4.3.2.1
Using The Taskbar . . . . . . . . . . . . . . . . . . . .64
4.4
The System Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
4.5
Using A Dialogue Box . . . . . . . . . . . . . . . . . . . . . . . . . .68
Chapter 5: Configuration
5.1
The Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
5.2
Control Panel Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
5.3
Basic Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
5.3.1 Display Properties . . . . . . . . . . . . . . . . . . . . . . . . .76
5.3.1.1
Display Contrast . . . . . . . . . . . . . . . . . . . . .77
5.3.1.2
Display Backlight . . . . . . . . . . . . . . . . . . . .77
5.3.1.3
Display Appearance . . . . . . . . . . . . . . . . . . .79
5.3.2 Keyboard Properties . . . . . . . . . . . . . . . . . . . . . . . .80
5.3.2.1
Key Repeat. . . . . . . . . . . . . . . . . . . . . . . .80
5.3.2.2
Keyboard Backlight . . . . . . . . . . . . . . . . . . .81
5.3.2.3
Keyboard One Shot Modes . . . . . . . . . . . . . . .82
5.3.3 Power Management Properties. . . . . . . . . . . . . . . . . . .83
5.3.3.1
Battery Capacity . . . . . . . . . . . . . . . . . . . . .83
5.3.3.2
Power Saving Schemes . . . . . . . . . . . . . . . . .84
5.3.4 Calibrating The Touchscreen . . . . . . . . . . . . . . . . . . .85
5.4
Advanced Configuration . . . . . . . . . . . . . . . . . . . . . . . . .86
Teklogix 7535 Hand-Held Computer User Manual iii
Contents
5.5
Scanner Properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
5.5.1 Scanner Options. . . . . . . . . . . . . . . . . . . . . . . . . . 87
5.5.2 Bar Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
5.5.3 Bar Code Settings . . . . . . . . . . . . . . . . . . . . . . . . . 90
5.5.3.1
Code 39 Settings . . . . . . . . . . . . . . . . . . . . 90
5.5.3.2
Code 128 Settings . . . . . . . . . . . . . . . . . . . 93
5.5.3.3
EAN 13 Settings . . . . . . . . . . . . . . . . . . . . 94
5.5.3.4
EAN 8 . . . . . . . . . . . . . . . . . . . . . . . . . 96
5.5.3.5
UPC And EAN Settings . . . . . . . . . . . . . . . . 97
5.5.3.6
UPC A Settings . . . . . . . . . . . . . . . . . . . . . 97
5.5.3.7
UPC E Settings . . . . . . . . . . . . . . . . . . . . . 98
5.5.3.8
Codabar Size And Characters . . . . . . . . . . . . . 99
5.5.3.9
Code 93 Size And Characters . . . . . . . . . . . . . 99
5.5.3.10 Code 11 . . . . . . . . . . . . . . . . . . . . . . . . .100
5.5.3.11 I 2 of 5 Settings . . . . . . . . . . . . . . . . . . . . .101
5.5.3.12 MSI/PLESSY Settings . . . . . . . . . . . . . . . . .102
5.5.3.13 D 2 of 5 Settings . . . . . . . . . . . . . . . . . . . .103
5.5.3.14 IATA 2 of 5 Settings . . . . . . . . . . . . . . . . . .104
5.5.3.15 Postal: Australian . . . . . . . . . . . . . . . . . . . .104
5.5.3.16 Postal: Japanese . . . . . . . . . . . . . . . . . . . .105
5.5.3.17 Postal: Korean . . . . . . . . . . . . . . . . . . . . .105
5.5.3.18 Postal: PlaNET . . . . . . . . . . . . . . . . . . . . .105
5.5.3.19 Postal: PostNET . . . . . . . . . . . . . . . . . . . .105
5.5.3.20 Postal: Royal Mail . . . . . . . . . . . . . . . . . . .105
5.5.3.21 DataMatrix (2D) . . . . . . . . . . . . . . . . . . . .106
5.5.3.22 Maxicode (2D) . . . . . . . . . . . . . . . . . . . . .106
5.5.3.23 PDF-417 (2D) . . . . . . . . . . . . . . . . . . . . .106
5.5.3.24 Micro PDF-417 (2D) . . . . . . . . . . . . . . . . . .107
5.5.3.25 QR Code (2D) . . . . . . . . . . . . . . . . . . . . .107
5.5.3.26 RSS Code (2D) . . . . . . . . . . . . . . . . . . . . .107
5.5.3.27 Aztec . . . . . . . . . . . . . . . . . . . . . . . . . .107
Chapter 6: Tekterm Application
6.1
The Tekterm Application. . . . . . . . . . . . . . . . . . . . . . . . .113
6.2
Additional Keyboard Functions . . . . . . . . . . . . . . . . . . . . .113
6.2.1 Function Keys And Softkey Function Keys . . . . . . . . . . .113
6.2.1.1
Function Keys . . . . . . . . . . . . . . . . . . . . .113
6.2.1.2
Softkey Function Keys . . . . . . . . . . . . . . . . .114
6.2.2 Macro Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . .115
6.3
Keyboard Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . .116
iv Teklogix 7535 Hand-Held Computer User Manual
Contents
6.3.1 View Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
6.3.1.1
Changing Font Sizes . . . . . . . . . . . . . . . . . . 116
6.3.1.2
Panning The Screen Contents . . . . . . . . . . . . . 116
6.3.1.3
Exiting View Mode . . . . . . . . . . . . . . . . . . 117
6.3.2 Menu Mode And Switching Between Applications . . . . . . . 118
6.3.2.1
Using The Task Manager To Switch Between Applications
118
6.4
The Tekterm Status Area . . . . . . . . . . . . . . . . . . . . . . . . 119
6.5
TESS Emulation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
6.5.1 Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . 120
6.5.2 Working With Multiple Sessions . . . . . . . . . . . . . . . . 120
6.5.3 The Field Types . . . . . . . . . . . . . . . . . . . . . . . . . 120
6.5.4 IBM 5250 Emulation Keys. . . . . . . . . . . . . . . . . . . . 121
6.5.5 Data Entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
6.5.5.1
TESS Edit Modes And Cursor Movement . . . . . . 122
6.5.5.2
<DEL> Key Behaviour In TESS . . . . . . . . . . . 123
6.5.5.3
<BKSP> Key Behaviour In TESS . . . . . . . . . . . 124
6.5.6 TESS Status Message . . . . . . . . . . . . . . . . . . . . . . 125
6.5.7 Lock Messages . . . . . . . . . . . . . . . . . . . . . . . . . . 126
6.5.8 Control Commands. . . . . . . . . . . . . . . . . . . . . . . . 126
6.5.9 Resetting A TESS Session . . . . . . . . . . . . . . . . . . . . 126
6.5.10 The Local Menu . . . . . . . . . . . . . . . . . . . . . . . . . 127
6.5.11 Selecting Another Host Computer . . . . . . . . . . . . . . . . 127
6.5.12 Queuing Mode . . . . . . . . . . . . . . . . . . . . . . . . . . 128
6.6
ANSI Emulation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
6.6.1 Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . 128
6.6.2 Sending Data To The Host . . . . . . . . . . . . . . . . . . . . 129
6.6.3 Psion Teklogix Keyboard And VT220 Equivalent Keys . . . . 129
6.6.4 Block Mode (Local Editing) . . . . . . . . . . . . . . . . . . . 130
6.6.5 Working With Sessions . . . . . . . . . . . . . . . . . . . . . 131
6.6.5.1
Establishing A New Session . . . . . . . . . . . . . . 131
6.6.5.2
Listing Sessions And Moving To Other Sessions . . . 131
6.6.5.3
Closing A Session . . . . . . . . . . . . . . . . . . . 131
6.6.5.4
Printing A Screen . . . . . . . . . . . . . . . . . . . 132
6.6.5.5
Smart Echo – Disabling . . . . . . . . . . . . . . . . 132
6.7
The Tekterm Startup Display Menu. . . . . . . . . . . . . . . . . . . 132
6.8
Working With Menus . . . . . . . . . . . . . . . . . . . . . . . . . . 133
6.8.1 Using The Keyboard To Navigate Through Menus . . . . . . . 133
Teklogix 7535 Hand-Held Computer User Manual v
Contents
6.8.1.1
Sub-Menus . . . . . . . . . . . . . . . . . . . . . . .133
6.8.1.2
Numeric Parameters . . . . . . . . . . . . . . . . . .134
6.8.1.3
Y/N Parameters. . . . . . . . . . . . . . . . . . . . .134
6.8.1.4
Alpha Parameters. . . . . . . . . . . . . . . . . . . .134
6.8.1.5
String Entry Parameters . . . . . . . . . . . . . . . .135
6.8.2 Using The Touchscreen To Navigate Through Menus . . . . . .137
6.8.2.1
Sub-Menus . . . . . . . . . . . . . . . . . . . . . . .137
6.8.2.2
Numeric Parameters . . . . . . . . . . . . . . . . . .137
6.8.2.3
Y/N Parameters. . . . . . . . . . . . . . . . . . . . .138
6.8.2.4
Alpha Parameters. . . . . . . . . . . . . . . . . . . .138
6.8.2.5
String Entry Parameters . . . . . . . . . . . . . . . .138
6.8.3 Saving Changes To Parameters . . . . . . . . . . . . . . . . . .138
6.8.4 Retrieving Default Parameter Values. . . . . . . . . . . . . . .139
6.9
Resetting The 7535 Hand-Held Computer . . . . . . . . . . . . . . .139
6.10 The Parameters Menu . . . . . . . . . . . . . . . . . . . . . . . . . .139
6.10.1 Security Settings . . . . . . . . . . . . . . . . . . . . . . . . .140
6.11 Display Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . .140
6.12 More Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . .141
6.13 Radio Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . .142
6.14 System Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . .145
6.14.1 Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . .145
6.14.1.1 Macros . . . . . . . . . . . . . . . . . . . . . . . . .145
6.14.1.2 Indicators . . . . . . . . . . . . . . . . . . . . . . . .148
6.14.1.3 Softkeys. . . . . . . . . . . . . . . . . . . . . . . . .149
6.14.1.4 Cntrl Panel . . . . . . . . . . . . . . . . . . . . . . .149
6.14.2 Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .150
6.14.3 Power Mgmt . . . . . . . . . . . . . . . . . . . . . . . . . . .151
6.14.4 Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .151
6.14.4.1 Default Mode . . . . . . . . . . . . . . . . . . . . . .151
6.14.4.2 User Level Options . . . . . . . . . . . . . . . . . . .152
6.14.4.3 Sup. Password . . . . . . . . . . . . . . . . . . . . .152
6.15 Scanner Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . .153
6.16 View Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .154
6.16.1 Split Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . .155
6.16.1.1 Splitting And Displaying Screens . . . . . . . . . . .155
6.16.1.2 Moving Between Split Screens. . . . . . . . . . . . .156
6.16.1.3 Toggling Between Full & Split Screens . . . . . . . .156
6.16.1.4 Using The Asterisk As A Wild Card . . . . . . . . . .157
6.16.2 Custom Characters (Unicode™) . . . . . . . . . . . . . . . . .157
vi Teklogix 7535 Hand-Held Computer User Manual
Contents
6.16.2.1 Creating A Unicode™ Character . . . . . . . . . . . 157
6.16.2.2 Displaying The Unicode™ Pop-up Window . . . . . 158
6.17 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
6.17.1 ANSI Settings . . . . . . . . . . . . . . . . . . . . . . . . . . 161
6.17.1.1 Host Conn . . . . . . . . . . . . . . . . . . . . . . . 162
6.17.1.2 Screen . . . . . . . . . . . . . . . . . . . . . . . . . 163
6.17.1.3 Xmit Modes . . . . . . . . . . . . . . . . . . . . . . 166
6.17.1.4 Kbd Modes. . . . . . . . . . . . . . . . . . . . . . . 170
6.17.1.5 Edit Modes. . . . . . . . . . . . . . . . . . . . . . . 173
6.17.1.6 Serial . . . . . . . . . . . . . . . . . . . . . . . . . . 174
6.17.1.7 Host Char Set . . . . . . . . . . . . . . . . . . . . . 174
6.17.1.8 Anchor View . . . . . . . . . . . . . . . . . . . . . . 175
6.17.2 TESS Settings . . . . . . . . . . . . . . . . . . . . . . . . . . 176
6.17.2.1 Host Conn. . . . . . . . . . . . . . . . . . . . . . . . 177
6.17.2.2 Screen . . . . . . . . . . . . . . . . . . . . . . . . . 178
6.17.2.3 Characters . . . . . . . . . . . . . . . . . . . . . . . 180
6.17.2.4 Tests . . . . . . . . . . . . . . . . . . . . . . . . . . 182
6.17.2.5 Features . . . . . . . . . . . . . . . . . . . . . . . . 183
6.17.2.6 Scanner. . . . . . . . . . . . . . . . . . . . . . . . . 186
6.17.2.7 Fields. . . . . . . . . . . . . . . . . . . . . . . . . . 188
6.17.2.8 Anchor View . . . . . . . . . . . . . . . . . . . . . . 190
6.18 Ports– Tether And Console . . . . . . . . . . . . . . . . . . . . . . . 191
6.18.1 Tether And Console Port Peripheral Options . . . . . . . . . . 191
6.18.2 Tether And Console Port Parameter Settings . . . . . . . . . . 192
6.18.3 Tether And Console Port Scan-See Parameters . . . . . . . . . 195
6.18.3.1 Scan-See Sub-Menu – Mapping The Viewport . . . . 195
6.18.3.2 Scan-See Keyboard Mapping . . . . . . . . . . . . . 200
6.19 Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201
6.19.1 Network Ctrl Panel Settings . . . . . . . . . . . . . . . . . . . 201
6.19.1.1 NETWLAN – Configuring The Radio . . . . . . . . 202
6.19.2 802.IQ v2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202
Chapter 7: Peripheral Devices & Accessories
7.1
External Bar Code Readers . . . . . . . . . . . . . . . . . . . . . . . 207
7.1.1 PowerScan™ Standard, LR and XLR Bar Code Scanners . . . 207
7.1.2 Entering Data With The Bar Code Reader . . . . . . . . . . . . 207
7.2
The 7535 Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207
7.2.1 Lithium-Ion Battery Safety Precautions . . . . . . . . . . . . . 208
7.3
Important Charger Safety Instructions . . . . . . . . . . . . . . . . . 209
Teklogix 7535 Hand-Held Computer User Manual vii
Contents
7.4
Chargers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .210
7.5
Gang Charger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .210
7.5.1 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . .210
7.5.2 Operator Controls . . . . . . . . . . . . . . . . . . . . . . . . .211
7.5.3 Charge Indicators . . . . . . . . . . . . . . . . . . . . . . . . .211
7.5.4 Charging Batteries . . . . . . . . . . . . . . . . . . . . . . . .212
7.5.5 Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . .212
7.5.5.1
Excessive Charge Duration. . . . . . . . . . . . . . .212
7.5.5.2
Indicator Flashing Red . . . . . . . . . . . . . . . . .212
7.5.5.3
Power LED Does Not Light Up . . . . . . . . . . . .213
7.5.5.4
Indicator Does Not Light When Battery Installed . . .213
7.6
Combo Charger . . . . . . . . . . . . . . . . . . . . . . . . . . . . .213
7.6.1 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . .213
7.6.2 Operator Controls . . . . . . . . . . . . . . . . . . . . . . . . .214
7.6.3 Using the Combo Charger With The 7535 . . . . . . . . . . . .214
7.6.4 7.2.4 Charging The Spare Battery . . . . . . . . . . . . . . . .214
7.6.5 Charge Indicators . . . . . . . . . . . . . . . . . . . . . . . . .215
7.6.6 Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . .215
7.7
Combo Dock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .216
7.7.1 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . .216
7.7.2 Using The Combo Dock . . . . . . . . . . . . . . . . . . . . .216
7.7.3 Network Access. . . . . . . . . . . . . . . . . . . . . . . . . .216
7.7.4 Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . .217
7.8
Quad Dock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .217
7.8.1 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . .217
7.8.2 Indicators And Controls . . . . . . . . . . . . . . . . . . . . .218
7.8.3 Using The Quad Dock . . . . . . . . . . . . . . . . . . . . . .218
7.8.4 Network Access. . . . . . . . . . . . . . . . . . . . . . . . . .218
7.8.4.1
Network Addressing . . . . . . . . . . . . . . . . . .218
7.8.5 Battery Charging . . . . . . . . . . . . . . . . . . . . . . . . .219
7.8.6 Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . .219
7.8.6.1
Network Link Unsuccessful . . . . . . . . . . . . . .219
7.8.6.2
7535 LED Does Not Light When Docked . . . . . . .219
7.8.6.3
7535 Battery Does Not Charge When Docked. . . . .219
7.9
Portable Docking Module (PDM) . . . . . . . . . . . . . . . . . . . .219
7.10 Bluetooth Peripherals . . . . . . . . . . . . . . . . . . . . . . . . . .222
7.11 The 7535 Picker Cradle . . . . . . . . . . . . . . . . . . . . . . . . .222
viii Teklogix 7535 Hand-Held Computer User Manual
Contents
7.11.1 Mounting Recommendations . . . . . . . . . . . . . . . . . . 223
7.11.1.1 Mounting Template . . . . . . . . . . . . . . . . . . 223
7.11.2 Wiring Guidelines . . . . . . . . . . . . . . . . . . . . . . . . 224
7.11.3 Using The Picker Cradle . . . . . . . . . . . . . . . . . . . . . 224
7.11.4 Maintaining The Picker Cradle . . . . . . . . . . . . . . . . . 224
7.11.5 The Powered Cradle Option . . . . . . . . . . . . . . . . . . . 225
7.11.5.1 Wiring Vehicle Power To The Cradle . . . . . . . . . 225
7.11.6 The Port Replicator. . . . . . . . . . . . . . . . . . . . . . . . 226
Chapter 8: Specifications
8.1
7535 Hand-Held Computer Specifications . . . . . . . . . . . . . . . 229
8.2
Radio Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . 230
8.3
Bar Code Scanning . . . . . . . . . . . . . . . . . . . . . . . . . . . 230
8.3.1 Internal Scanners . . . . . . . . . . . . . . . . . . . . . . . . . 231
8.3.2 Internal Scanner Port . . . . . . . . . . . . . . . . . . . . . . . 231
8.3.3 External Scanners . . . . . . . . . . . . . . . . . . . . . . . . 231
8.4
Internal Scanner Specifications . . . . . . . . . . . . . . . . . . . . . 231
8.4.1 SE1200 High Performance & Long Range Specs . . . . . . . . 232
8.4.2 SE1223 Advanced Long Range & SE2223 2-D Specs . . . . . 233
8.4.3 Symagery SX4000 & Welch Allyn IT4200 Imager Specs . . . 234
8.5
External Scanner Specifications. . . . . . . . . . . . . . . . . . . . . 236
8.5.1 PowerScan™ LR and XLR Industrial Scanner Specs . . . . . . 236
8.5.2 PowerScan™ Standard Range Scanner Specs . . . . . . . . . . 238
8.6
Lithium-Ion Battery Pack . . . . . . . . . . . . . . . . . . . . . . . . 240
Appendix A: Support Services And Worldwide Offices
A.1 Support Services. . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
A.1.1
Canada and USA: Technical Support and Repair Services . . . A-1
A.1.2
International Support . . . . . . . . . . . . . . . . . . . . . . A-1
Appendix B: Port Pinouts And Cable Diagrams
B.1 7535 Tether Port Pinout . . . . . . . . . . . . . . . . . . . . . . . . . B-1
B.2 Docking Port & Battery Connector - TBD . . . . . . . . . . . . . . . B-1
Teklogix 7535 Hand-Held Computer User Manual ix
A
PPROVALS
A
ND
S
AFETY
S
UMMARY
Declaration Of Conformity
7535 Hand Held Micro-computer Product:
Application of Council
Directive(s):
Conformity Declared to Standards:
Manufacturer:
Year of Manufacture:
Manufacturer’s Address in the European
Community:
Legal Representative
EMC Directive: 89/336/EEC
Low Voltage Directive: 73/23/EEC
EN 301 489-17: v1.1.1; 09-2000
EN 50082-1:1997; EN 50082-2:1995;
EN 55022:1994, Class B;
EN 61000-3-2; EN 61000-3-3
EN 55024:1998;
EN 61000-4-2; ±4kV CD; ±8kV AD
EN 61000-4-3; 3V/m, 80-1000 MHz
EN 61000-4-4; ±0.5kV on I/O lines, ±1kV Power lines
EN 61000-4-5; ±2kV Common; ±1kV Differential mode
EN 61000-4-6; 3VRMS, 150kHz-80MHz
EN 61000-4-11; AC Mains Ports
EN 60950: 1992 + A1 + A2 + A3 + A4 +A11
PSION TEKLOGIX INC.
2100 Meadowvale Boulevard
Mississauga, Ontario, Canada
L5N 7J9
2003
PSION TEKLOGIX S.A.
La Duranne; 135 Rue Rene Descartes; BP 421000
13591 Aix-En-Provence
Cedex 3; France
Information Technology Equipment Type of Equipment:
Equipment Class: Commercial and Light Industrial
I the undersigned hereby declare that the equipment specified above conforms to the above directives and standards.
Manufacturer: Rob Williams
Vice President of Engineering
Psion Teklogix Inc. Ontario
Domique Binckly
Vice President International Sales
Psion Teklogix S.A. France
Teklogix 7535 Hand-Held Computer User Manual xi
Approvals And Safety Summary
This equipment complies with Class B Part 15 of the FCC rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by Psion Teklogix, the party responsible for compliance, may void the user's authority to operate the equipment.
D
O
N
OT
O
PERATE
I
N
A
N
E
XPLOSIVE
A
TMOSPHERE
Operating Psion Teklogix equipment where explosive gas is present may result in an explosion.
D
O
N
OT
R
EMOVE
C
OVERS
O
R
O
PEN
E
NCLOSURES
To avoid injury, the equipment covers and enclosures should only be removed by qualified service personnel. Do not operate the equipment without the covers and enclosures properly installed.
C
AUTION
!
Danger of explosion if a 7535 battery is incorrectly handled, charged, disposed of or replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the instructions described in “Lithium-Ion Battery Safety Precautions” on page 208. Carefully review all battery safety issues.
V
ORSICHT
!
Explosiongefahr bei unsachgemäßem Austausch der Batterie Ersatz nur durch denselben oder einen vom Hersteller empfohlenen gleichwertigen
Typ. Entsorgung gebrauchter Batterien nach Angaben des Herstellers.
xii Teklogix 7535 Hand-Held Computer User Manual
I
NTRODUCTION
1.1 About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.2 Text Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.3 About The 7535 Hand-Held Computer . . . . . . . . . . . . . . . . . . . . 5
1.3.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.3.2 The 7535 Hand-Held Computer . . . . . . . . . . . . . . . . . . . . . 7
1.3.3 The 7535 Hand-Held Safety Labels . . . . . . . . . . . . . . . . . . . 9
Teklogix 7535 Hand-Held Computer User Manual 1
Chapter 1: Introduction
About This Manual
1.1 About This Manual
This manual describes how to configure, operate and maintain the Psion Teklogix
7535 hand-held computer.
Chapter 1: Introduction provides a basic overview of the 7535 hand-held.
Chapter 2: Unpacking & Basic Checkout describes the steps required to get the 7535 ready for operation.
Chapter 3: Getting To Know Your 7535 describes the 7535 features and outlines how to charge and maintain the battery.
This chapter also provides a description of the keyboard, how to navigate in
Microsoft® Windows® CE, how to use the internal scanner, and so on.
Chapter 4: Working With Windows CE describes the Microsoft® Windows® CE desktop and how to use it. This chapter also outlines the basics of moving around a Windows CE window, selecting and opening icons, files, folders and working with a Windows dialogue box.
Chapter 5: Configuration provides a description of the Windows CE Control Panel and how to use it to configure the 7535, along with the scanners attached to the hand-held, and so on.
Chapter 6: Tekterm Application describes TESS and ANSI operations. This chapter also provides descriptions of the Tekterm parameters.
Chapter 7: Peripheral Devices & Accessories describes the peripherals and accessories available for your 7535 hand-held.
Chapter 8: Specifications details radio, hand-held computer and battery specifications.
Appendix A: Support Services And Worldwide Offices provides the helpdesk phone number at the Mississauga, Ontario, Canada office and details the support services available. This appendix also lists the worldwide office addresses and phone numbers.
Appendix B: Port Pinouts And Cable Diagrams includes pinouts and diagrams of the ports and cables.
Teklogix 7535 Hand-Held Computer User Manual 3
Chapter 1: Introduction
Text Conventions
1.2 Text Conventions
Note: Notes highlight additional helpful information.
Important: These statements provide particularly important instructions or additional information that is critical to the operation of the equipment.
Warning: These statements provide critical information that may prevent physical injury, equipment damage or data loss.
4 Teklogix 7535 Hand-Held Computer User Manual
Chapter 1: Introduction
About The 7535 Hand-Held Computer
1.3 About The 7535 Hand-Held Computer
The 7535 is a ruggedized hand-held personal computer, running the Microsoft®
Windows® CE.net operating system. It is intended for use in commercial and light industrial applications with a focus on real time wireless data transactions. All possible bar code input methodologies are supported by one of the variety of scanners available. Optimization for specific operational environments is supported with a wide range of peripheral options and carrying accessories.
1.3.1 Features
• Rugged design:
sealed from water and dust to IP54 (light rain) rating.
withstands multiple drops of up to 6.5 feet onto concrete.
• Large 240 x 320 portrait mode display that is available in colour or black and white with or without a touchscreen
• Automatic backlighting for both the display and the keypad.
automatic backlight and contrast control.
daylight readable screen.
• Processor and memory:
Intel PXA255 400Mhz CPU with 32 MB FLASH and 64 MB RAM standard.
• Microsoft® Windows® CE.net operating system
• Application software:
Internet Explorer 5.5 for CE.
Tekterm terminal emulation.
• Ergonomic keyboard designed to accommodate left- and right-handed use.
• Two keyboard formats available:
58-key with 6 function keys (standard).
36-key large button with 10 function keys.
keypads feature EL backlight for visibility in low-light conditions.
• Wireless communication:
Compact FLASH slot normally equipped with an IEEE 802.11b
11 Mbps 2.4GHz Wi-Fi radio.
Teklogix 7535 Hand-Held Computer User Manual 5
Chapter 1: Introduction
Features
standard antenna integrated onto radio card.
optional high performance internal antenna available.
Bluetooth SD I/O radio.
• Expansion slot:
SD I/O slot that supports extra FLASH memory (up to 512 MB) or a
Bluetooth radio.
• Programming environment:
HTML
.net Compact framework
Java, Visual C++
• Bar code applications:
internal 1D and 2D scan engines.
internal CMOS image capture scan engine.
supports decoded and undecoded tethered scanners.
• RFID applications:
internal dual laser scanner/RFID engine.
external tethered RFID reader.
6 Teklogix 7535 Hand-Held Computer User Manual
1.3.2 The 7535 Hand-Held Computer
Chapter 1: Introduction
The 7535 Hand-Held Computer
Figure 1.1 7535 With 58-Key Keyboard
Teklogix 7535 Hand-Held Computer User Manual 7
Chapter 1: Introduction
The 7535 Hand-Held Computer
Figure 1.2 7535 Docking Port
Figure 1.3 Tether Port
Figure 1.4 Scanner Window
8 Teklogix 7535 Hand-Held Computer User Manual
1.3.3 The 7535 Hand-Held Safety Labels
Chapter 1: Introduction
The 7535 Hand-Held Safety Labels
Figure 1.5 Laser Warning Labels
Figure 1.6 Radio Labels
Teklogix 7535 Hand-Held Computer User Manual 9
Chapter 1: Introduction
The 7535 Hand-Held Safety Labels
Figure 1.7 Manufacturer’s Label
Warning: Using controls or adjustments or performing procedures other than those specified herein may result in hazardous radiation exposure.
10 Teklogix 7535 Hand-Held Computer User Manual
U
NPACKING
& B
ASIC
C
HECKOUT
2.1 Preparing The 7535 For Operation . . . . . . . . . . . . . . . . . . . . . 13
2.1.1 Equipment You Need To Get Started . . . . . . . . . . . . . . . . . 13
2.1.2 Charging The Battery . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.1.3 Attaching Carrying Accessories . . . . . . . . . . . . . . . . . . . 13
2.1.3.1 Attaching The Hand Strap . . . . . . . . . . . . . . . . . . 14
2.1.3.2 Attaching The Pistol Grip . . . . . . . . . . . . . . . . . . 15
2.2 Powering Up The 7535 And Configuring The Radio . . . . . . . . . . . . 16
2.2.1 Installing The Battery And Switching The 7535 On . . . . . . . . . 17
2.2.2 Configuring An IEEE 802.11 Radio . . . . . . . . . . . . . . . . . 18
2.3 Advanced NETWLAN Settings . . . . . . . . . . . . . . . . . . . . 22
2.3.1 Preferred Networks . . . . . . . . . . . . . . . . . . . . . . 23
2.3.2 Advanced Network Access . . . . . . . . . . . . . . . . . . 23
2.3.3 Configuring WEP Keys . . . . . . . . . . . . . . . . . . . . . . . . 24
2.5 Checking The Scanner . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
2.6 Uploading New Applications . . . . . . . . . . . . . . . . . . . . . . . . 29
2.8 Resetting The 7535 Hand-Held . . . . . . . . . . . . . . . . . . . . . . . 30
2.7 Calibrating The Touchscreen . . . . . . . . . . . . . . . . . . . . . . . . 30
Teklogix 7535 Hand-Held Computer User Manual 11
Chapter 2: Unpacking & Basic Checkout
Preparing The 7535 For Operation
2.1 Preparing The 7535 For Operation
Typically, 7535 hand-helds are configured at the factory and arrive ready for use.
Although the 7535 is equipped with an internal Compact Flash and SD I/O slot, these slots are not intended for user modification. If a device needs to be changed or added in these slots, contact qualified Psion Teklogix personnel. Refer to
Appendix A: Support Services And Worldwide Offices for the service number closest to you.
2.1.1 Equipment You Need To Get Started
You’ll need:
• A 7535 compatible battery charger, docking station or portable docking module (PDM) with power supply.
• An operating wireless network (if you are not operating the equipment in batch mode).
• A medium Phillips head screwdriver.
2.1.2 Charging The Battery
Important: The 7535 uses a high capacity Lithium-Ion battery. It is critical that you review the battery safety guidelines in “Lithium-Ion
Battery Safety Precautions” on page 208 before charging the battery.
Batteries shipped from the factory are not charged. They must be fully charged prior to use. Full capacity may not be reached until at least 5 full charge/discharge cycles have been performed.
7535 batteries can be charged using a gang charger or the 7535 internal charger.
When using the internal charger, a suitable power source is required. All chargers and docking stations are described in Chapter 7: Peripheral Devices & Accessories beginning on page 210.
2.1.3 Attaching Carrying Accessories
Psion Teklogix recommends that a carrying accessory – a hand strap, pistol grip or shoulder strap – be installed on the 7535 before use.
If your hand-held is not fitted with a hand strap or pistol grip, you can install either using the carrying accessory kit supplied. You’ll need:
• A Phillips head screwdriver.
Teklogix 7535 Hand-Held Computer User Manual 13
Chapter 2: Unpacking & Basic Checkout
Attaching The Hand Strap
Important: Do not use adhesives such as Loctite to secure the screws on the carrying accessories. These chemicals may damage the plastic casing.
2.1.3.1
Attaching The Hand Strap
Note: A Phillips head screwdriver is required.
Psion Teklogix recommends that the hand strap provided with your 7535 always be used. However, if your unit has an internal scanner and you plan to use the pistol grip accessory, a hand strap is not required.
Two Phillips head screws are provided with the hand strap.
• Attach the strap to the two threaded inserts located at the back of the 7535 near the top of the unit.
Figure 2.1 Attaching The Hand Strap
14 Teklogix 7535 Hand-Held Computer User Manual
Chapter 2: Unpacking & Basic Checkout
Attaching The Pistol Grip
• Stretch the handstrap toward the base of the 7535, and hook the bottom of the handstrap into the slot near the base of the battery pack.
Figure 2.2 Hooking The Hand Strap To The 7535
2.1.3.2
Attaching The Pistol Grip
Note: A Phillips head screwdriver is required.
The pistol grip is attached to the back of the 7535 using the four threaded inserts in the upper part of the 7535 casing. Four black #4-40 Phillips head screws are provided with this accessory.
Note: Prior to installation, make sure the trigger mechanism is securely snapped into the pistol grip body and that the trigger operates properly.
Teklogix 7535 Hand-Held Computer User Manual 15
Chapter 2: Unpacking & Basic Checkout
Powering Up The 7535 And Configuring The Radio
• Position the pistol grip so that it fits snugly over the back of the unit and the inserts on the back of the 7535 align with the holes in the pistol grip.
Figure 2.3 Attaching The Pistol Grip
• Using a Phillips screwdriver, securely fasten the pistol grip to the back of the 7535.
2.2 Powering Up The 7535 And Configuring The Radio
Note: Psion Teklogix offers a Portable Docking Module (PDM) along with its power supply to help speed the checkout and confirmation process for your 7535. The PDM can power your hand-held with or without a battery installed in the 7535. Refer to Chapter 7: Peripheral Devices & Accessories beginning on page 205 for more information about this accessory.
16 Teklogix 7535 Hand-Held Computer User Manual
Chapter 2: Unpacking & Basic Checkout
Installing The Battery And Switching The 7535 On
2.2.1 Installing The Battery And Switching The 7535 On
If you are not using a docking station or PDM:
• Slide the charged battery with the moulded plastic facing you into the 7535.
Click the battery into place.
Figure 2.4 Installing The Battery
Note: If you are using a docking station, you can insert an uncharged battery, dock the unit and switch it on.
If you are using a PDM, you can configure your unit without a battery, with a charged battery or with an uncharged battery.
If you are using a hand strap:
• Hook the bottom of the hand strap into the slot at the base of the battery.
To switch the 7535 on:
• Press and hold down the <ENTER/ON> or the <SCAN> key for at least one second.
• When all four LEDs flash orange, release the <ENTER/ON> button.
A splash screen displaying the Psion Teklogix logo and the Microsoft®
Windows® CE. net logo appears. When Windows® CE has successfully loaded, the startup desktop is displayed.
Note: The screen may go blank for a few seconds after the splash screen loading bar reaches the end. This is part of the normal Windows CE cold boot process. The desktop is displayed after a few moments.
Teklogix 7535 Hand-Held Computer User Manual 17
Chapter 2: Unpacking & Basic Checkout
Configuring An IEEE 802.11 Radio
2.2.2 Configuring An IEEE 802.11 Radio
The most common 802.11b settings are configured as defaults. However, there are some fields that must be completed, including the ESSID of your access point and the security methods implemented in the network (including access keys). At various stages during network setup, you can tap on the taskbar radio icon to view detailed statistics such as the access point you are connected to, the radio strength, and so on.
Important: If the 7535 is equipped with a radio and it has never been configured, the radio settings dialogue box opens automatically when the unit is powered on. Follow the directions beginning at Step 4 on page 19 to configure the radio.
After the initial configuration, you must follow the directions beginning at Step 1 below to open the Control Panel and display the radio settings dialogue box.
To configure the 802.11b radio:
1. Open the
Control Panel
. If you have a touchscreen, tap on the
Control Panel
icon on the desktop. If you’re using a keyboard, press <BLUE> <0> and choose
Control Panel
from the
System Menu
.
2. Open the
Network and Dial-up Connections
applet.
Figure 2.5 Network And Dial-Up Connections
18 Teklogix 7535 Hand-Held Computer User Manual
Chapter 2: Unpacking & Basic Checkout
Configuring An IEEE 802.11 Radio
3. Choose the
NETWLAN1
icon to open the
802.11b Wireless LAN Settings
window.
4.
Figure 2.6 802.11b Wireless LAN Settings Window
IP Address
In the
IP Address
tab,
‘Obtain an IP address via DHCP’
is selected by default.
This is the most common configuration. If you prefer, choose
‘Specify an
IP address’,
and enter a static IP address.
Figure 2.7 IP Address Assignment
Note: If you enter a static IP Address, press <TAB> to switch between the address entry fields. Use the <LEFT> and <RIGHT> arrow keys to position the cursor in an IP address field. (If you do not have a static
IP Address allocated to you, contact your System Administrator.)
Teklogix 7535 Hand-Held Computer User Manual 19
Chapter 2: Unpacking & Basic Checkout
Configuring An IEEE 802.11 Radio
5.
Wireless Networks
First, make certain that the check box next to
‘Use Windows to configure network setting’
is enabled (
√
) so that the items you configure in this window are activated. If this option is not enabled, press <TAB> to highlight the check box, and press <SPACE> to enable it.
List of networks broadcasting ESSID
Preferred networks
6.
Figure 2.8 Radio Settings
ESSID (Extended Service Set Identifier)
Press the <TAB> key again to highlight the
‘Available networks...’
list, and choose an access point that is broadcasting its ESSID. Since access
points are generally secure, they will most likely not be listed here; you’ll need to define the access point to which your 7535 will connect.
Press the <TAB> key until the <Add...> button is highlighted. Press
<ENTER> to open the
Wireless Network Properties
dialogue box.
Type the appropriate ESSID (Extended Service Set Identifier) in the
Network name
text entry field at the top of this dialogue box.
Type your access point’s
ESSID here.
Figure 2.9 Wireless Network Properties
20 Teklogix 7535 Hand-Held Computer User Manual
Chapter 2: Unpacking & Basic Checkout
Configuring An IEEE 802.11 Radio
The
Network name
field can contain a maximum of 32 characters. The name assigned here is listed in the preferred network list labelled
‘Automatically connect to these networks:’
(see Figure 2.8 on page 20).
Note: Keep in mind that the 7535 will only communicate with access points that are configured with the same ESSID.
7.
Ad Hoc And Infrastructure
If you are using an “Infrastructure” network – one in which 7535s must pass data through an access point – leave the checkbox next to
‘This is an ad hoc network’
blank.
If you are using an “Ad Hoc” network – a network in which 7535s pass data
directly to other 7535s without an access point – press the <TAB> key to highlight
‘This is an ad hoc network’,
and press the <SPACE> key to enable (
√
) the Ad Hoc check box.
8.
Saving The Configurations
In the
Wireless Network Properties
dialogue box, press the <TAB> key until the <OK> button is highlighted. Press <ENTER> to save the configurations.
9. Once the
NETWLAN Settings
dialogue box (Figure 2.8 on page 20) is displayed, you need to save all your radio configurations. Press <TAB> to highlight the
Wireless Networks
tab, and press <ENTER> to save the configuration.
10.
Reviewing The Configurations
To determine if the radio configuration has been successfully saved, in the
Network and Dial-up Connections
window (see Figure 2.6 on page 19), choose the
NETWLAN1
icon to redisplay the
802.11b Wireless LAN Settings
window. Review the contents under each tab in the window to make certain that your settings have been saved. To be sure that the unit is communicating with an access point, check that the radio strength meter in the taskbar is active.
To determine if you have successfully connected to the access point network and have received an IP Address from the DHCP server, open the
NETWLAN1
status window from the
System Tray
in the taskbar.
Teklogix 7535 Hand-Held Computer User Manual 21
Chapter 2: Unpacking & Basic Checkout
Advanced NETWLAN Settings
Press <BLUE><0> and choose
System Tray
from the
System Menu
. Use the
<LEFT> and <RIGHT> arrow keys to highlight the radio strength meter and then, press <ENTER>. The
NETWLAN1
statistics window is displayed.
Check that the “
Network Name
” field displays the one you specified.
Choose the <More...> button with the <RIGHT> or <LEFT> arrow key to launch the
NETWLAN1
status window. Choose the
IP Information
tab to determine the unit IP Address. If you prefer, you can determine the unit IP Address from the MS DOS command prompt located in the Windows folder in the
Explorer application. Type “ipconfig” in the command line to display your
IP Address.
2.3 Advanced NETWLAN Settings
This section describes a few additional options in the
NETWLAN Settings
dialogue box.
Keep in mind that these options are not necessary for radio configuration. All the steps necessary for your radio to communicate with your network are detailed in
“Configuring An IEEE 802.11 Radio” beginning on page 18.
Preferred Networks
Figure 2.10 Radio Settings
Move up &
Move down Buttons
Advanced
Button
22 Teklogix 7535 Hand-Held Computer User Manual
Chapter 2: Unpacking & Basic Checkout
Preferred Networks
2.3.1 Preferred Networks
Each network that you configure is listed in the preferred networks list under
‘Automatically connect to these networks’
. These are the preferred networks that the 7535 attempts to connect with in sequence, beginning at the top of the list. If you need to rearrange this list of networks – move networks up and down in the list:
• Press the <TAB> key to highlight the preferred networks list.
• Use the <UP> or <DOWN> arrow keys to highlight the network in the preferred list that you want to move up or down.
• To move the highlighted item in the list upward or downward, press <TAB> to highlight the <Move up> or <Move down> button.
• Press <ENTER> to move the item up or down in the preferred network list.
2.3.2 Advanced Network Access
If you have configured more than one network, the <Advance> button in the
NETWLAN
Settings
dialogue box (Figure 2.10 on page 22) is used to specify the type of network your 7535 can access.
To access the
Advance
dialogue box:
1. Press the <TAB> key to highlight the <Advance> button, and press
<ENTER>.
Figure 2.11 Advanced Network Settings
Teklogix 7535 Hand-Held Computer User Manual 23
Chapter 2: Unpacking & Basic Checkout
Configuring WEP Keys
These options specify the type of network connection your 7535 will choose from the preferred network list labelled
‘Automatically connect to these networks:’
(see Figure 2.10 on page 22).
‘Any available network (AP preferred)’
– connect to an infrastructure network or an ad hoc network listed in the preferred network list.
‘Access point (infrastructure) only’
– connect to an infrastructure network listed in the preferred network list.
‘Computer-to-computer (ad hoc) only’
– connect to an ad hoc (peer-to-peer) network listed in the preferred network list.
‘Automatically connect to non-preferred networks’
– connect to an infrastructure network not listed in the preferred network connection list.
2. When you’ve made your selections, press <TAB> to highlight the
<Close> button, and press <ENTER>.
2.3.3 Configuring WEP Keys
To set up WEP (Wired-Equivalent Privacy) encryption to prevent others from accidentally accessing your network, follow the steps in this section.
1. Open the
Control Panel
.
2. Open the
Network and Dial-up Connections
applet.
Figure 2.12 Network And Dial-Up Connections
24 Teklogix 7535 Hand-Held Computer User Manual
Chapter 2: Unpacking & Basic Checkout
Configuring WEP Keys
3. Choose the
NETWLAN1
icon to open the
802.11b Wireless LAN Settings
window.
Figure 2.13 802.11b Wireless LAN Settings Window
Figure 2.14 Radio Settings
Teklogix 7535 Hand-Held Computer User Manual 25
Chapter 2: Unpacking & Basic Checkout
Configuring WEP Keys
4. Display the options under the
Wireless Network
tab. If it’s not displayed, use the <TAB> key to highlight the left-most tab in the
NETWLAN Settings
dialogue box –
IP Address
. Press the <RIGHT> arrow key to display the options under the
Wireless Network
tab.
Preferred Networks
Figure 2.15 Wireless Networks Tab
5. Press the <TAB> key to highlight the <Add..> button, and press
<ENTER> to display the
Wireless Network Properties
dialogue box.
√
Modify WEP Ke
Figure 2.16 Wireless Network Properties
26 Teklogix 7535 Hand-Held Computer User Manual
Chapter 2: Unpacking & Basic Checkout
Configuring WEP Keys
Important: To add or modify a WEP Key in an EXISTING network:
• In the ‘preferred network’ list (see Figure 2.15 on page 26), highlight the network in which you want to add or modify a
WEP key, and then
• RATHER THAN SELECTING THE <Add...> BUTTON, select the <Properties> button.
6. Press <TAB> until
‘Data encryption (WEP enabled)’
<SPACE> key to enable (
√
) this option.
is highlighted. Press the
7. To define your own WEP keys, press the <TAB> key to highlight
‘The key is provided automatically’
. Press <SPACE> to deselect the checkbox.
8. Press the <TAB> key to highlight the <Modify WEP Keys...> button, and press <ENTER>.
Figure 2.17 WEP Key Settings
9. Press the <TAB> key to move from field to field in this dialogue box.
Network key:
Used to specify a 5 or 13 ASCII character sequence or an equivalent 10 or 26 Hexadecimal digit sequence that matches the active WEP key on the access point.
Teklogix 7535 Hand-Held Computer User Manual 27
Chapter 2: Unpacking & Basic Checkout
Additional Radio Security Options
Key format:
Defines the format WEP keys used – either ASCII alphanumeric characters or Hexadecimal digits. For example, if the access point has an active key of bobby , the 7535
Key format
would be set to ‘ASCII characters’ and the
Network key
would be defined as bobby .
Key length:
Defines the length of the keys as either
104 bits/13 characters
or
40 bits/5 characters
. (Intel radios support both these lengths. Other radios may be restricted.)
Key Index (advanced):
Identifies the WEP key. Up to 4 keys can be indexed.
Keep in mind that
Key Index
numbering for Windows CE starts at 0 (zero), so if an access point and a hand-held have been assigned a Transmit Key of 1 ,
Windows CE will match that with
Key Index
0 (zero). If an access point and a hand-held have been assigned a Transmit Key of 4 , Windows CE will match that with
Key Index
3 , and so on.
10. Press <TAB> to highlight the <OK> button, and press <ENTER>.
2.4 Additional Radio Security Options
Additional security options can be set through the
Wireless Network Properties
dialogue box.
Figure 2.18 Network Authentication, EAP and 802.1X
Network Authentication (Shared Mode)
If
‘Network Authentication’
is enabled (
√
), the access point sends a known unencrypted challenge packet to the 7535 radio which encrypts the packet and sends it back to the access point. The access point attempts to decrypt the
28 Teklogix 7535 Hand-Held Computer User Manual
Chapter 2: Unpacking & Basic Checkout
Checking The Scanner encrypted packet and forwards an authentication response packet back to the 7535 radio, indicating the success or failure of the decryption. If the packet is successfully encrypted/decrypted, the user is authenticated.
If this option is disabled (the default setting), network authentication is not used.
EAP (Extensible Authentication Protocol) and Enable 802.1x
“802.1x” is the IEEE standard that offers additional security for local area networks. It provides authentication for user devices attached to an Ethernet network, whether wired or wireless. A packet encapsulated in an “EAP” is used in conjunction with the “802.1x” standard to authenticate users at the
MAC layer.
Available EAPs are listed in the dropdown menu next to the
‘EAP’
option.
To enable “802.1x”, press <TAB> to highlight
<SPACE> key to enable (
√
) it.
‘Enable 802.1x’
, and press the
2.5 Checking The Scanner
If your 7535 is equipped with an internal scanner, it will successfully decode most
1D bar codes as delivered. Press the SCAN button and check for a valid decode on any UPC bar code. If desired, set the “Dot Time” parameter to zero in the ‘Teklogix
Scanners’ applet in the
Control Panel
to turn off the default aiming dot.
Performance is improved if you disable all unneeded bar codes under the ‘Bar
Codes’ dialogue screen. Review “Scanner Properties” on page 86 for details about bar codes.
2.6 Uploading New Applications
The simplest way to upload Windows CE.net applications into the 7535 is to use a
PDM with a USB equipped PC. Refer to “Portable Docking Module (PDM)” on page 219 for more details about the PDM.
• Attach the supplied USB cable between the host port on your PC and the
PDM ‘device’ port.
• Install the PDM on the 7535 and turn it on.
Teklogix 7535 Hand-Held Computer User Manual 29
Once WinCE is booted, the PC should indicate it has found a new USB storage device. (You will need the Windows 2000 operating system or later).
[Final details TBD]
To upload an application:
• Drag the file onto the USB device folder.
• Shut down the USB device on the PC before disconnecting the 7535.
• Perform a cold reboot of the 7535 – hold down the <ENTER> and
<BLUE> keys for at least a second.
2.7 Calibrating The Touchscreen
If your 7535 is equipped with a touchscreen, it will need to be calibrated. Refer to
“Calibrating The Touchscreen” on page 44 for details.
2.8 Resetting The 7535 Hand-Held
Note: You do not need to reset your 7535 after configuring the radio.
To reset the 7535:
• Press and hold down the <BLUE> key and the <ENTER/ON> key simultaneously for a minimum of six seconds.
A reset results in a complete reboot of the unit. All RAM memory contents are lost.
The contents of the flash memory and memory card are preserved.When the 7535 is reset, the screen displays the Psion Teklogix and Microsoft® Windows® CE.net splash screen before displaying the startup desktop.
G
ETTING
T
O
K
NOW
Y
OUR
7535
3.1 Features Of The 7535 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
3.2 The Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
3.2.1 Battery Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
3.2.2 Removing And Installing The Battery Pack . . . . . . . . . . . . . 34
3.2.3 Charging The Battery . . . . . . . . . . . . . . . . . . . . . . . . . 35
3.3 Switching The 7535 Hand-Held On And Off . . . . . . . . . . . . . . . . 36
3.4 The Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
3.4.1 Modifier Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
3.4.1.1 Activating Modifier Keys . . . . . . . . . . . . . . . . . . 39
3.4.1.2 Locking Modifier Keys . . . . . . . . . . . . . . . . . . . 39
3.4.2 The Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
3.4.3 The 58-Key Keyboard . . . . . . . . . . . . . . . . . . . . . . . . 40
3.4.4 The 36-Key Keyboard . . . . . . . . . . . . . . . . . . . . . . . . 40
3.4.5 The Keypad Backlight . . . . . . . . . . . . . . . . . . . . . . . . 42
3.5 The Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
3.5.1 Adjusting The Display Backlight . . . . . . . . . . . . . . . . . . . 43
3.5.2 Adjusting The Contrast On Monochrome Displays . . . . . . . . . 43
3.5.3 Calibrating The Touchscreen . . . . . . . . . . . . . . . . . . . . . 44
3.6 7535 Hand-Held Computer Indicators . . . . . . . . . . . . . . . . . . . 45
3.6.1 LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
3.6.1.1 Charge LEDs. . . . . . . . . . . . . . . . . . . . . . . . . 46
3.6.1.2 Radio Traffic LEDs . . . . . . . . . . . . . . . . . . . . . 46
3.6.1.3 Scan LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . 47
3.6.2 Onscreen Indicators. . . . . . . . . . . . . . . . . . . . . . . . . . 47
3.6.3 Audio Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
3.6.3.1 Adjusting The Beeper Volume . . . . . . . . . . . . . . . . 49
3.7 Internal Scanners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
3.7.1 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
3.7.2 Scanning Techniques . . . . . . . . . . . . . . . . . . . . . . . . . 51
3.7.3 Scan LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . 52
3.7.4 Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
3.7.5 Operating One Dimensional (1D) Internal Laser Scanners. . . . . . 53
3.7.6 Operating Internal PDF Laser Scanners . . . . . . . . . . . . . . . 53
3.7.7 Operating Internal Two Dimensional (2D) Imager Scanners. . . . . 53
Teklogix 7535 Hand-Held Computer User Manual 31
Chapter 3: Getting To Know Your 7535
3.8 Connecting & Disconnecting Tethered Peripherals . . . . . . . . . . . . . 54
3.9 Monitoring The Battery And Maximizing Run Time . . . . . . . . . . . . 55
3.10 Monitoring The Network Connection . . . . . . . . . . . . . . . . . . . 57
3.11 Uploading Data In A Docking Station . . . . . . . . . . . . . . . . . . . 57
3.12 General Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
3.12.1 Caring For The Touchscreen . . . . . . . . . . . . . . . . . . . . . 58
3.12.2 Cleaning The 7535 . . . . . . . . . . . . . . . . . . . . . . . . . . 58
32 Teklogix 7535 Hand-Held Computer User Manual
3.1 Features Of The 7535
7535 Screen
Ambient Light Sensor
Chapter 3: Getting To Know Your 7535
Features Of The 7535
Docking Port
Figure 3.1 Front Of 7535
Tether Port
Stylus
(Pointing Tool)
Scanner Window
Battery Pack
Tether Port
Figure 3.2 Back Of 7535
Teklogix 7535 Hand-Held Computer User Manual 33
Chapter 3: Getting To Know Your 7535
The Battery
3.2 The Battery
The 7535 hand-held operates with a Lithium-Ion battery pack. Preparing the hand-held unit for operation requires that a battery pack be charged and installed in the unit.
3.2.1 Battery Safety
Important: Before attempting to install, use or charge the battery pack, it is critical that you review and follow the important safety guidelines in the section entitled “Lithium-Ion Battery Safety Precautions” beginning on page 208.
3.2.2 Removing And Installing The Battery Pack
Note: TURN OFF THE 7535 HAND-HELD BEFORE REMOVING THE
BATTERY PACK. If you do not turn the hand-held off before removing the battery, it may be necessary to reboot the unit. Any active sessions will be lost.
Removing The Battery Pack
• If your 7535 is equipped with a hand strap, unhook it from the base of the battery.
• Press down the release tab at the top of the battery, and slide the battery out.
34 Teklogix 7535 Hand-Held Computer User Manual
Chapter 3: Getting To Know Your 7535
Charging The Battery
Installing The Battery Pack
To install the battery pack:
• Slide the battery pack with the moulded plastic facing you into the 7535.
Click the battery into place.
Figure 3.3 Installing The Battery Pack
• If your computer is equipped with a hand strap, insert the hook at the end of the hand strap into the slot at the base of the battery.
3.2.3 Charging The Battery
Important: FOR DETAILED INFORMATION about 7535 chargers and
docking stations, refer to Chapter 7: Peripheral Devices & Accessories beginning on page 205.
All batteries must be charged before use. The 7535 battery can be charged with a variety of chargers. These include:
• 6-Gang Charger (Model #HU3006) – charges up to six Lithium-Ion batteries at one time.
• Portable Docking Module (PN 1030085) – charges the 7535 battery (with the battery installed in the unit).
• Combo Charger (Model #HU3002) – a desktop charger that charges the
7535 internal battery along with a spare battery pack.
Teklogix 7535 Hand-Held Computer User Manual 35
Chapter 3: Getting To Know Your 7535
Switching The 7535 Hand-Held On And Off
• Combo Docking Station (Model #HU4002) – operates as both a charger and a docking station. Operating as a charger, both the battery installed in the computer and a spare battery can be charged simultaneously. When used as a docking station, it provides connectivity (10/100 BaseT Ethernet interface) to a host Ethernet network, primarily for batch data file transfers.
• Quad Docking Station (Model #HU4004) – can charge the battery of up to four 7535s inserted in the docking station while transferring data through an
Ethernet connection.
• Powered Cradle – can charge the 7535 with the battery installed in the hand-held.
It can take from 1.5 to 4 hours to charge a battery. The 7535’s intelligent charging system protects the battery from over-charging by terminating the charge process when the battery is at maximum capacity.
Note: Refer to “Monitoring The Battery And Maximizing Run Time” on page 55 for additional information about the 7535 battery.
Important: To avoid damaging the battery, chargers will not begin the charge process until the battery temperature is between 0˚C (32˚F) and
39˚C (102˚F). If the battery is too hot or cold, the battery status
LED flashes yellow and the charge is suspended. Refer to
Table 3.1, “Charge LEDs” on page 46 for details.
3.3 Switching The 7535 Hand-Held On And Off
Switching On The 7535
• Press and hold down the <ENTER/ON> key for at least one second.
• When all four LEDs flash orange, release the <ENTER/ON> button.
A splash screen displaying the Psion Teklogix logo and the Microsoft®
Windows® CE. net logo appears followed by the startup desktop.
Note: If the 7535 is in suspend state, pressing any key ‘wakes’ the unit from this state. The screen in which you were working before the computer entered suspend state is displayed.
36 Teklogix 7535 Hand-Held Computer User Manual
Chapter 3: Getting To Know Your 7535
The Keyboard
Switching Off The 7535
Important: Keep in mind that turning off the 7535 does not result in a complete reboot; rather, the unit enters a power-saving,
“suspend” state. When the 7535 is turned on from suspend state, operation resumes within a few seconds.
To switch off the 7535:
• Press the <BLUE> key, and then press the <ENTER/ON> key.
Important: If the word ‘BLUE’ is displayed in uppercase in the taskbar area at the bottom of the screen, this key is locked “on” – the 7535 will not switch off. Press the <BLUE> key again to unlock it; then press <BLUE> <ENTER/ON> to switch the 7535 off.
3.4 The Keyboard
The 7535 offers two types of keyboard layouts – a 58-key keyboard and a 36-key, large button keyboard. Most of the keys on these keyboards operate much like a desktop computer. Where a key or key function is not consistent with the PC keyboard, the differences are noted.
The <BLUE> and <ORANGE> modifier keys provide access to additional keys and system functions. These functions are colour coded in orange and blue print above the keyboard keys.
Teklogix 7535 Hand-Held Computer User Manual 37
Chapter 3: Getting To Know Your 7535
Modifier Keys
F11 F12
F1 F2
F13 F14
F3 F4
CTRL
1
!
GHI
4
$
PQRS
&
7
SPACE
.
F15
'
+
F5
F19
F9
ABC
2
@
JKL
5
%
TUV
*
8
MENU
)
0
F16 -
F6
M3 M5
M1
SHIFT
F17
F7
M4 M6
M2
3
DEF
#
MNO
6
^
WXYZ
(
9
TAB
E
S
C
E
N
T
E
R
O
N
O
F
F
DEL
BKSP
ALT
F18
F8
F20
F10
Figure 3.4 58-Key And 36-Key Keyboard Layouts
3.4.1 Modifier Keys
The <SHIFT>, <CTRL>, <ALT>, <BLUE> and <ORANGE> keys are modifier keys. Pressing a modifier key changes the function of the next key pressed. For example, on a 58-key keyboard, a square bracket is printed in orange print above the
<4> key. Pressing the <ORANGE> key followed by the <4> key displays a square bracket rather than the number 4.
The <SHIFT>, <CTRL> and <ALT> keys operate much like a desktop keyboard except that they are not chorded (two keys held down simultaneously). The modifier key must be pressed first followed by the key whose function you want modified.
38 Teklogix 7535 Hand-Held Computer User Manual
Chapter 3: Getting To Know Your 7535
Activating Modifier Keys
3.4.1.1
Activating Modifier Keys
When a modifier key is pressed once, it is displayed in lowercase letters in the taskbar at the bottom of the 7535 screen. For example, if the <CTRL> key is pressed, ctrl key is displayed at the bottom of the unit screen. Once the next key is pressed, the modifier key becomes inactive and disappears from the taskbar.
3.4.1.2
Locking Modifier Keys
When a modifier key is pressed twice, it is ‘locked’ on. A ‘locked’ modifier key is displayed in uppercase letters in the taskbar. For example, pressing the <BLUE> key twice locks it on – it is displayed as BLUE KEY in the taskbar at the bottom of the computer screen.
The locked modifier key will remain active until it is pressed a third time to unlock or turn it off. Once a modifier key is unlocked (pressed a third time), the uppercase representation at the bottom of the screen is no longer displayed.
3.4.2 The Keys
The <SHIFT> Key
The <SHIFT> key is used to display uppercase alpha characters. A ‘locked’
<SHIFT> key (pressed twice) operates like the <CAPS LOCK> key on a desktop keyboard.
The Arrow Keys
The Arrow keys move the cursor around the screen in the direction of the arrow – up, down, left and right. The cursor is the flashing box or underline character that indicates where the next character you type will appear.
The <BKSP/DEL> Key
The <BKSP> key (sometimes referred to as destructive backspace) moves the cursor one character to the left, erasing the incorrectly entered key stroke.
The <DEL> key (<BLUE> <BKSP>) erases the character at the cursor position.
The <CTRL> And <ALT> Key
The <CTRL> and <ALT> keys modify the function of the next key pressed and are application dependent.
Teklogix 7535 Hand-Held Computer User Manual 39
Chapter 3: Getting To Know Your 7535
The 58-Key Keyboard
The <TAB> Key
Typically, the <TAB> key moves the cursor to the next field to the right or downward.
The <ESC> Key
Generally, this key is used as a keyboard shortcut to close the current menu, dialogue box or activity and return to the previous one.
The <SPACE> Key
Pressing this key inserts a blank space between characters. In a Windows dialogue box, pressing the <SPACE> key enables (
√
) or disables a checkbox.
The <SCAN> Key
Pressing the <SCAN> key – the yellow key with the star-burst scan symbol on it – activates the scanner beam while pressed. For units that do not have internal scanners, this key is either inoperable or can be remapped to another key function
(such as an <ENTER> key).
3.4.3 The 58-Key Keyboard
In addition to alphanumeric keys that are directly accessible on the keyboard (no key combination is required) and the keys described in this chapter, the 58-key keyboard also provides function keys and macro keys. These keys are not used as part of the
Windows CE operating system. They can be custom defined for each application.
The Tekterm application utilizes these keys. Refer to “Additional Keyboard
Functions” on page 113 for details about Tekterm keys.
3.4.4 The 36-Key Keyboard
On 36-key 7535s, all alpha characters are printed on the unit plastic in orange typeface above the numeric keys. To access an alpha character, you must first press the <ORANGE> key and then press the numeric key above which the alpha character you want to type is printed.
Because the alpha keys on a 36-key keyboard are laid out much like the letters on a telephone – generally in groups of three letters per numeric key – you need to take a few extra steps to access the alphabetic characters. The examples in this section help illustrate how to access alpha characters.
40 Teklogix 7535 Hand-Held Computer User Manual
Chapter 3: Getting To Know Your 7535
The 36-Key Keyboard
Choosing A Single Alpha Character
The examples below illustrate how to access A, B and C, all of which are printed in
orange characters above the numeric key, <2>.
To choose the letter ‘a’:
• Press the <ORANGE> key, and press the numeric key <2>.
To choose the letter ‘b’:
• Press the <ORANGE> key twice to lock it ‘on’, and press <2> twice.
• Press the <ORANGE> key again to unlock or turn it off.
To choose the letter ‘c’:
• Press the <ORANGE> key twice to lock it ‘on’.
• Press <2> three times, and then
• Press the <ORANGE> key again to unlock or turn it off.
Creating Uppercase Letters
To display a capital letter:
• Press the <ORANGE> key and then the <SHIFT> key before typing the alpha character.
Choosing More Than One Alpha Character From The Same Key
If you need to choose more than one alpha character from a single key, you’ll need to press the ‘Accept’ key between alpha selections. The ‘Accept’ key is presented as an arrow
⇒ symbol above the ‘0’ (zero) key. Pressing this key signals the 7535 to display the alpha character you’ve chosen and await the next selection from the same key.
For example, suppose you want to type the letters ‘a’, ‘b’ and ‘c’. These letters are all accessible from the numeric key, <2>.
To type the letter ‘a’:
• Press the <ORANGE> key twice to lock it ‘on’, and then press the numeric key, <2>.
• Press the ‘Accept’ key <
⇒
> to indicate that the letter ‘a’ should be accepted and that another letter from the same key will be chosen.
Teklogix 7535 Hand-Held Computer User Manual 41
Chapter 3: Getting To Know Your 7535
The Keypad Backlight
To type the letter ‘b’:
• Press the <2> key twice.
• Press <
⇒
> to accept the letter ‘b’.
To type the letter ‘c’:
• Press the <2> key three.
When you have completed your alpha selections from this key, you can do one of the following:
• If you want to choose additional alpha characters from another key(s), leave the <ORANGE> key ‘on’, and press the next numeric key that supports the alpha character you require.
• If you do not want to choose any additional alpha characters, press
<ORANGE> again to unlock or turn ‘off’ the key and end alpha selection.
Choosing Multiple Alpha Characters From A Range Of Keys
If you plan on choosing alpha characters from a number of different keys, you are
not required to press the ‘Accept’ <
⇒
> key after each alpha selection. The <
⇒
> key is only required when you are choosing more than one alpha character from the
same key – e.g., ‘a’, ‘b’ and ‘c’ from the <2> key.
Suppose you want to type the letters ‘a’, ‘d’ and ‘g’. These alpha characters are accessed from the numeric keys <2>, <3> and <4>.
• With the <ORANGE> key locked ‘on’ (press twice), press <2> to type the letter ‘a’.
• Press <3> to type ‘d’, and press <4> to type the letter ‘g’.
• To end alpha selection, press the <ORANGE> key a third time to unlock it.
3.4.5 The Keypad Backlight
The intensity of the keypad backlight and the conditions under which this backlight is activated can be configured using the Keyboard icon in the Windows CE Control Panel .
The behaviour of the keypad backlight is tailored in the Keyboard Properties dialogue box.
Refer to “Keyboard Backlight” on page 81 for details about this option.
Note: Keep in mind that this option may be restricted to supervisory use only.
42 Teklogix 7535 Hand-Held Computer User Manual
Chapter 3: Getting To Know Your 7535
The Display
3.5 The Display
7535s are equipped with display backlighting to improve character visibility in low light conditions. The unit switches on when a key is pressed and the ambient light is below the set threshold. A light sensor on the front of the hand-held determines the ambient light level. On some displays, the contrast can also be adjusted to further improve character visibility.
3.5.1 Adjusting The Display Backlight
The behaviour of the display backlight – the ambient light threshold below which the backlight will become active and the intensity of the backlight – can be specified in the Display Properties dialogue box in the Windows CE Control Panel .
Note: Refer to “Display Backlight” on page 77 for details about the Display
Properties dialogue box.
3.5.2 Adjusting The Contrast On Monochrome Displays
Note: In addition to the manual adjustments described in this section, the display contrast can also be adjusted using the Windows CE Control Panel.
Refer to “Display Contrast” on page 77 for details about this dialogue box.
On monochrome displays only, the display contrast can be adjusted from the unit keyboard using the <BLUE> key and function keys <F1> and <F2>.
To darken the display:
• Press the <BLUE> key, and then press <F1> . Repeat this key combination until the contrast suits your needs. To work more efficiently with these keys, refer to the note below.
To lighten the display:
• Press the <BLUE> key, and then press <F2> . Repeat this key combination until the contrast suits your needs. To work more efficiently with these keys, refer to the note below.
Note: To adjust the display contrast quickly, lock the <BLUE> key “on” by pressing it twice. You can then press the <F1> and <F2> function keys until you can easily read the contents of the screen.
When you have satisfactorily adjusted the contrast, press the <BLUE> key a third time to unlock or turn it off.
Teklogix 7535 Hand-Held Computer User Manual 43
Chapter 3: Getting To Know Your 7535
Calibrating The Touchscreen
3.5.3 Calibrating The Touchscreen
If your 7535 touchscreen has never been calibrated or if you find that the stylus pointer is not accurate when you tap on an item, use the Stylus Properties dialogue box in the Windows CE Control Panel to recalibrate the screen.
• In the Control Panel , choose the Stylus icon to display the Stylus Properties window.
Figure 3.5 Stylus Icon
• Select the Calibration tab, and then choose the ‘ Recalibrate ’ button.
Figure 3.6 Calibration Screen
• Follow the directions on the calibration screen to calibrate the screen.
44 Teklogix 7535 Hand-Held Computer User Manual
Chapter 3: Getting To Know Your 7535
7535 Hand-Held Computer Indicators
3.6 7535 Hand-Held Computer Indicators
7535s use LEDs (Light Emitting Diode), onscreen messages and audio tones as indicators.
3.6.1 LEDs
The 7535 is equipped with four tri-coloured LEDs. This section outlines what these
LEDs indicate.
Important: If an LED is illuminated in red, the operator should be cautious as this generally indicates an abnormal operating condition or active laser emission.
Radio Traffic
LED
Scanner
LED
User
Application
LED
Charge
LED
Figure 3.7 Keyboard LEDs
Teklogix 7535 Hand-Held Computer User Manual 45
Chapter 3: Getting To Know Your 7535
Charge LEDs
3.6.1.1
Charge LEDs
The lower-right LED is reserved for internal charger/power status. This indicator is active even when the 7535 is inserted in a docking station (and in suspend mode) so that the charge status of the battery can be detected easily.
Function Charge LED Behaviour
External power not available.
Fully charged to within 95% of charge capacity.
LED off.
LED displays solid green colour.
Quick charge successfully completed to within 75% of charge capacity.
Charge in progress.
LED flashes slow green.
LED displays solid yellow colour.
Cell temperature out of range for charge.
LED flashes yellow.
Unable to charge battery.
Charge circuit failure.*
LED displays solid red colour.
LED flashes fast red.*
*If the charge fails, refer to the charger troubleshooting sections in Chapter 7: Peripheral Devices &
Accessories beginning on page 210 for helpful details.
Table 3.1 Charge LEDs
3.6.1.2
Radio Traffic LEDs
The upper-left LED on your 7535 flashes either orange or green to indicate when the radio transmits and receives data.
Note: Keep in mind that while the standard 802.11b radio supports the transmit/receive LED, not all radios support this function.
Function
Radio Transmit
Radio Receive
Radio Traffic LED Behaviour
LED flashes orange.
LED flashes green.
Table 3.2 Transmit and Receive LEDs
46 Teklogix 7535 Hand-Held Computer User Manual
Chapter 3: Getting To Know Your 7535
Scan LEDs
3.6.1.3
Scan LEDs
Successful scans are indicated in two ways – with a scan LED and with an audio tone.
Function
Scan in progress
Successful scan
Unsuccessful scan
Scan LED Behaviour
LED displays solid red during scan.
LED displays solid green after decode.
Off when scan ended.
LED flashes red.
Table 3.3 Scan LED
3.6.2 Onscreen Indicators
The taskbar at the bottom of the screen displays a variety of system status indicators.
Figure 3.8 Taskbar
This display changes dynamically, and only those icons that are applicable are displayed. For example, if a radio is not installed in your 7535, the radio signal icon is not displayed in the taskbar.
Teklogix 7535 Hand-Held Computer User Manual 47
Chapter 3: Getting To Know Your 7535
Onscreen Indicators
Modifier Key Indicators
<SHIFT>, <CTRL>, <ALT>, <BLUE> and <ORANGE> are modifier keys that have onscreen indicators to show when a key is active or locked. If a modifier key is pressed once to activate it, the key is displayed in the taskbar in lowercase characters
– for example, pressing the <BLUE> key once displays blue key in the taskbar. If a modifier key is pressed twice, it is ‘locked on’ and the onscreen indicator is displayed in uppercase letters in the taskbar – for example, pressing <BLUE> twice displays BLUE KEY in the taskbar.
Battery Gauge
The battery shaped icon displayed in the taskbar provides a visual indication of the remaining battery power. The icon acts as a meter that is either full, at three-quarter level, half, quarter level or empty.
When the battery level is low – approximately 15 minutes from empty – a warning window pops up. When the battery power is completely depleted, a final warning window indicates that the 7535 will be powered down.
Full 75% 50% 25% Empty
Radio Signal Quality
Increasing radio signal quality is represented by longer, filled bars within this icon.
100%
Link Broken
Tethered Devices
When a peripheral is attached to the tether port and activated, an associated icon appears in the taskbar. The sample to the left indicates that a USB device is connected to the tether port.
Scanner USB Device RFID Serial Device Scan-See
48 Teklogix 7535 Hand-Held Computer User Manual
Chapter 3: Getting To Know Your 7535
Audio Indicators
Docking Device
When a 7535 is inserted in a docking station, charger or cradle, an associated icon appears in the taskbar.
Gang Charger, Combo Charger
Combo Docking & Docking Station
Quad Docking Station Power Cradle Portable Docking
Module (PDM)
Security Level
Security levels can be set to limit access to the Windows CE operating system. In addition, applications can be restricted to prevent inadvertent changes.
3.6.3 Audio Indicators
The 7535 beeper provides a variety of sounds and can be configured to emit a sound when a key is pressed, a keyboard character is rejected, scan input is accepted or rejected, an operator’s entry does not match in a match field or the battery is low.
3.6.3.1
Adjusting The Beeper Volume
The volume function keys located along the top of the keyboard are used to adjust the beeper volume emitted from your 7535. The increase volume function key is labelled with a plus sign . The decrease volume key is labelled with a minus sign .
On 58-key keyboards, the volume function keys are accessed by pressing
<BLUE> <F5> and <F6>.
On 36-key keyboards, the volume function keys are accessed by pressing
<BLUE> < F3> and <F4>.
To increase the beeper volume:
• Press the <BLUE> key and then, the increase volume function key .
Repeat this key combination until the volume is sufficient for your needs.
To work more efficiently with these keys, refer to the note on page 50.
Teklogix 7535 Hand-Held Computer User Manual 49
Chapter 3: Getting To Know Your 7535
Internal Scanners
To decrease the beeper volume:
• Press the <BLUE> key and then, press the decrease volume function key . Repeat this key combination until the volume is low enough for your needs. To work more efficiently with these keys, refer to the note below.
Note: To adjust the beeper volume more quickly, lock the <BLUE> key “on” by pressing it twice. You can then press the appropriate volume function keys until the beeper volume suits your needs.
When you have satisfactorily adjusted the beeper volume, press the
<BLUE> key a third time to unlock or turn it off.
3.7 Internal Scanners
The scanner installed in your unit can be configured using the Scanner Properties dialogue box in the Control Panel .
The 7535 can be equipped with a:
• One dimensional (1D) internal laser scanner,
• Internal PDF laser scanner, or a
• Two dimensional (2D) internal imager scanner.
It is critical that you review the warnings listed in Section 3.7.1 on page 51 before using any of the scanners described in this chapter. “Scanning Techniques” on page 51 outlines the mechanics of a successful scan. In addition, review “Scan LED
Indicators” on page 52 to better understand how to interpret whether or not a bar code has been successfully scanned. Finally, “Troubleshooting” on page 52 provides some helpful suggestions should the scan fail.
50 Teklogix 7535 Hand-Held Computer User Manual
Chapter 3: Getting To Know Your 7535
Warnings
3.7.1 Warnings
For your own safety, it is critical that you comply with the following warnings:
1. Do not look into the laser beam or point the beam at people or animals.
2. CAUTION – Using controls or adjustments, or performing procedures other than those specified herein may result in hazardous radiation exposure.
3. CAUTION – The use of optical instruments with this product will increase eye hazard.
4. This product contains a laser scanner that emits less than 1.0 mW average radiant power at a wavelength of 650 or 680 nm. This product complies with 21 CFR 1040.10, 1040.11 and DIN EN
60825: July 1993, and is classified as a Class 2 laser product. The
SE12xxALR has an average radiated power of 1.5 mW.
3.7.2 Scanning Techniques
Note: The scanning techniques described here apply to internal and external scanners.
• Hold the scanner at an angle. Do not hold it perpendicular to the bar code.
Do not hold the scanner directly over the bar code. In this position, light can reflect back into the scanner’s exit window and prevent a successful decode.
• Scan the entire bar code. If you are using a 1D or 2D scanner, make certain that the scan beam crosses every bar and space on the bar code, including the margins on either end of the symbol.
If you are using a 2D imaging scanner, make certain the red, oval shaped framing mark is centered within the bar code you want to scan.
• Hold the scanner farther away for larger bar codes.
• Hold the scanner closer for bar codes with bars that are close together.
Teklogix 7535 Hand-Held Computer User Manual 51
Chapter 3: Getting To Know Your 7535
Scan LED Indicators
3.7.3 Scan LED Indicators
The 7535 scanner LED (the lower-left LED) indicates whether or not your scan is successful. The LED behaves as follows:
• Scan In Progress: scan LED displays solid red colour.
• Successful Scan: scan LED displays solid green colour and turns off when the scan is ended.
• Unsuccessful scan: scan LED flashes red.
A bar code icon appears on the screen during a scan. While the scanner beam is active, the onscreen message states – SCANNING. If the scan is successful, the bar code data is displayed on the screen until the scan button (or pistol trigger) is released.
3.7.4 Troubleshooting
If the scanner is not working, investigate the following:
• Is the 7535 on?
• Check that the bar code symbology being scanned is enabled for the 7535 you are using. Check any other parameters that affect the scanning procedure or the bar code.
• Check the bar code to make sure it is not damaged. Try scanning a different bar code to verify that the problem is not with the bar code.
• Check that the bar code is within the proper range.
• Does the hand-held display the warning without scanning? This suggests a hardware problem in the 7535.
• Is the laser beam scanning across the bar code?
• Once the scan beam has stopped, check the scanner window for dirt or fogging.
52 Teklogix 7535 Hand-Held Computer User Manual
Chapter 3: Getting To Know Your 7535
Operating One Dimensional (1D) Internal Laser Scanners
3.7.5 Operating One Dimensional (1D) Internal Laser Scanners
• Turn the 7535 on. Wait until the unit has booted up completely.
Important: If an aiming dot is available on the installed scanner, the dot will be enabled for a configurable time period (including off), after which normal scanning begins. Refer to “Dot Time” on page 136 for details.
Double-clicking the trigger will override the aiming delay and initiate an immediate scan. Note that the aiming dot is standard on long-range and high visibility internal scanners.
• Aim at the bar code and press the scan key or the trigger. A scan beam and a warning indicator appear until a successful decode is achieved or six seconds have elapsed.
3.7.6 Operating Internal PDF Laser Scanners
This scanner decodes PDF417 two-dimensional bar codes.
• Turn the 7535 on. Wait until the unit has booted up completely.
• Aim at the bar code and press the scan key or the trigger. The beam expands into a rectangle covering the bar code to properly scan it. The scan beam and a warning indicator are visible until a successful decode is achieved or three seconds have elapsed.
3.7.7 Operating Internal Two Dimensional (2D) Imager Scanners
An imager scanner takes a snap shot of a single bar code or multiple bar codes (at one time). It can find a bar code regardless of its orientation – that is, even a bar code printed at a 45 degree angle to the 7535 will be decoded successfully.
Because imager scanners generally have a shorter depth of field than laser scanners, some practise may be required to find the optimal distance from the types of bar codes being scanned. Although the imager includes illumination LEDs, ambient light will help the imager decode the bar codes, especially if the bar code is far from the 7535.
• Turn the 7535 computer on. Wait until the unit has booted up completely.
• Aim at the bar code and press the scan key or the trigger.
Teklogix 7535 Hand-Held Computer User Manual 53
Chapter 3: Getting To Know Your 7535
Connecting & Disconnecting Tethered Peripherals
• When the scan button or trigger is pressed, a red, oval shaped light (the framing marker) is displayed. Centre the framing marker in the field – either in the centre of the bar code you want to scan or in the centre of the area in which multiple bar codes are to be scanned.
Illumination LEDs will flash and a picture of the bar code(s) is taken.
3.8 Connecting & Disconnecting Tethered Peripherals
Tethered peripherals such as scanners and printers connect to the hand-held computer with a quick release, circular connector. When a peripheral is connected to the hand-held, the 7535 detects the peripheral and loads the necessary drivers for it.
An icon in the taskbar at the bottom of the screen provides a visual representation of the peripheral and indicates that it is ready for operation.
To attach the peripheral to the round, tether port on the side of the 7535:
• Insert the barrel of the plug into the tether port and rotate slowly until it clicks into place. The red dot on the port and on the connector should be aligned.
Figure 3.9 Attaching The Cable To The Tether Port
54 Teklogix 7535 Hand-Held Computer User Manual
Chapter 3: Getting To Know Your 7535
Monitoring The Battery And Maximizing Run Time
To remove the peripheral:
• Grasp the shell of the plug, and pull it back gently to unlock and release the connector.
Figure 3.10 Disconnecting The Tether Cable
Important: Never attempt to disconnect a peripheral by pulling the connector by the wire. The connector is locked into place and can only be unlocked and removed by pulling back the plug shell.
3.9 Monitoring The Battery And Maximizing Run Time
Under normal operating conditions, the battery lasts for a full 8-hour shift. As
Lithium-Ion batteries age, their capacity decreases gradually, and they are generally considered depleted after approximately 2 years of use (less than 60% of original capacity remaining). Keep in mind however that heavy usage or operating the 7535 at temperature extremes will shorten the battery life.
Lithium-Ion batteries do not require conditioning cycles and the 7535 battery system (including chargers) requires no user interaction to maintain peak performance.
Teklogix 7535 Hand-Held Computer User Manual 55
Chapter 3: Getting To Know Your 7535
Monitoring The Battery And Maximizing Run Time
To maximize the run time of your batteries, consider the following:
• The display backlight is the largest drain on the battery. Try to keep its brightness as low as possible.
• The hand-held is ‘event’ driven – that is, when the unit is not in use, it reverts to sleep mode (even when it appears to be running), saving battery power. Events include a key press, touchscreen taps and scan triggers.
Power consumption is reduced if you avoid unnecessary events, and allow the unit to sleep as much as possible.
• The 7535 battery is a ‘smart battery’ with built-in intelligence. The taskbar battery icon is a linear gauge used to estimate the remaining run time of the battery. It is important to note that the battery capacity icon displays quarter percentages of nominal capacity (the capacity of a new battery). An aged battery, even when fully charged, shows somewhat less capacity than nominal.
Double-tapping on the battery icon displays a dialogue box that provides detailed information about the battery status and performance. If the remaining capacity indication seems inaccurate, the battery may need recalibration. Recalibration requires that the battery be fully charged, discharged and then charged again before use. If the battery is fully discharged and
charged on a regular basis, recalibration should not be necessary.
• When the hand-held is switched off, it goes into a low-power, suspend state but continues to draw a small amount of power from the battery. This should not be an issue unless the unit is left in suspend state for more than a week – in this case, the battery should be removed.
• Batteries left for durations of more than one or two months should be fully charged, discharged and then charged again before use. This recalibrates the gas gauge and allows the internal electronics to determine the actual capacity of the battery.
• The hand-held can determine when the useful life of the battery has expired and will notify the user. Chargers may reject batteries that have exceeded their lifespan.
56 Teklogix 7535 Hand-Held Computer User Manual
Chapter 3: Getting To Know Your 7535
Monitoring The Network Connection
3.10 Monitoring The Network Connection
If your hand-held is equipped with a wireless LAN radio, it will typically associate with the nearest access point. The radio signal quality meter in the taskbar indicates the relative strength of the communication link.
To access the radio signal icon from the keyboard:
• Press <BLUE> <0> to display the System Menu .
• Choose System Tray from the menu.
• Use the <LEFT> and <RIGHT> arrow keys to highlight the radio signal icon in the taskbar.
• Press <ENTER> to display the radio quality dialogue box.
If you have a touchscreen:
• Tap on the radio icon in the taskbar to display the radio quality dialogue box.
Note: Moving in and out of the radio coverage area can have varying effects on a network session. At times, you may need to renew your connection by logging in again.
3.11 Uploading Data In A Docking Station
The Combo Docking and Quad Docking peripherals allow the 7535 to link to an
Ethernet network. They are typically used to upload transaction data to a server computer when a radio link in not available. When a 7535 is properly inserted in a docking station, a dock icon is displayed in the taskbar at the bottom of the 7535 screen. The 7535 also detects the presence of the Ethernet network. Review the documentation provided with the user application installed in your 7535 before preforming data uploads.
Teklogix 7535 Hand-Held Computer User Manual 57
Chapter 3: Getting To Know Your 7535
General Maintenance
3.12 General Maintenance
3.12.1 Caring For The Touchscreen
The top of the touchscreen is a thin, flexible polyester plastic sheet with a conductive coating on the inside. The polyester can be permanently damaged by harsh chemicals and is susceptible to abrasions and scratches. Using sharp objects on the touchscreen can scratch or cut the plastic, or crack the internal conductive coating.
The chemicals listed below must not come into contact with the touchscreen:
• mustard,
• sodium hydroxide,
• concentrated caustic solutions,
• benzyl alcohol, and
• concentrated miner acids.
If the touchscreen is used in harsh environments, consider applying a disposable screen protector (PN 1010029). These covers reduce the clarity of the display slightly but will dramatically extend the useful life of the touchscreen. When they become scratched and abraded, they are easily removed and replaced.
Note: If the environment is excessively harsh, consider using a tempered glass version of the 7535.
3.12.2 Cleaning The 7535
Important: Do not immerse the unit in water. Dampen a soft cloth with mild detergent to wipe the unit clean.
• Use only mild detergent or soapy water to clean the hand-held unit.
• Avoid abrasive cleaners, solvents or strong chemicals for cleaning. The
7535 has a plastic case that is susceptible to harsh chemicals. The plastic is partially soluble in oils, mineral spirits and gasoline. The plastic slowly decomposes in strong alkaline solutions.
• To clean ink marks from the keypad and touchscreen, use isopropyl alcohol.
58 Teklogix 7535 Hand-Held Computer User Manual
W
ORKING
W
ITH
W
INDOWS
CE
4.1 Navigating In Windows CE And Applications . . . . . . . . . . . . . . . 61
4.1.1 Navigating Using A Touchscreen And Stylus . . . . . . . . . . . . 61
4.1.2 Navigating Using The Keyboard . . . . . . . . . . . . . . . . . . . 61
4.2 Working With Files, Folders And Programs . . . . . . . . . . . . . . . . 62
4.3 The Startup Desktop . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
4.3.1 Accessing Desktop Icons . . . . . . . . . . . . . . . . . . . . . . . 63
4.3.2 The Taskbar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
4.3.2.1 Using The Taskbar . . . . . . . . . . . . . . . . . . . . . . 64
4.4 The System Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
4.5 Using A Dialogue Box . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Teklogix 7535 Hand-Held Computer User Manual 59
Scarica
Link pubblico aggiornato
Il link pubblico alla tua chat è stato aggiornato. Puoi visualizzare e gestire i tuoi link di chat dopo la registrazione qui.
Link pubblico del documento
Pubblicità
