advertisement
1.
INSTALLATION
The Live Player V5 is a software program that installs in a PC, and functions to monitor and playback the data collected in the VR-7000/7000S’s DRU, Long Term Device of the Data Collecting
Unit (DCU). Install the Live Player V5 in a PC using the program CD (supplied).
1.1
Installable PC
The Live Player V5 is compatible with the OS (Operating System) shown below. The OS language should be English or Japanese. The Live Player V5 may not operate properly on the PC with other
OS and language.
• Windows ® 10 (64 bit) • Windows ® 8.1 (32 bit, 64 bit) • Windows ® 7 (32 bit, 64 bit)
Required specifications for replay PC
• CPU: Pentium 350 MHz (or equivalent) or higher
• RAM: Minimum 1 GB
• HDD: Minimum 250 GB
• Screen resolution: XGA or higher (More than SXGA (1280x1024) recommended)
• CD-ROM drive (internal or external)
• LAN port
• USB port (2.0 compatible)
• DirectX
®
9.0c or higher
• Java ® (If there is no Java ® from the Internet.)
in the PC, download and install the latest Java ® program
• Microsoft ® Visual C++ ® 2005 SP1 (x86) or later
Note: Before you connect a PC to the VDR, set the IP address and subnet mask on the PC (see
1.2
How to Install the Live Player V5 and Set Up the
PC
The software program for the Live Player V5 is included in the program CD. Follow the appropriate procedure, depending on your OS. The procedure is comprised of the following two steps.
• Install the software.
• Set the IP address and subnet mask of the PC.
Note: The Live Player V5 version 1.20 or later is not compatible with version 1.10 or earlier. Therefore, the program CD has install programs for both latest version and version 1.10. If the Live Player V5 version 1.10 or earlier has been installed in your PC, uninstall the Live Player V5 before installing.
1
1. INSTALLATION
Firewall software block setting
Confirm that “JAVA (TM) Platform SE binary” is not blocked by the Firewall. If blocked, enable
“JAVA (TM) Platform SE binary”. When “JAVA (TM) Platform SE binary” is blocked, the Live Player V5 cannot connect with the VDR.
“Java(TM) Platform SE binary” is blocked, enable it.
To confirm the firewall settings, open the [Windows Firewall with Advanced Security] dialog box as follows:
• Windows
®
7 : [Start] button > [Control Panel] > [Windows Firewall] > [Advanced settings] > [Inbound Rules]
• Windows
®
8.1
: Open the desktop > Move the mouse pointer to the bottom right edge of the screen > [Settings] > [Control Panel] > [System and Security] > [Windows Firewall] > [Advanced settings] > [Inbound Rules]
• Windows ® 10 : [Start] button > [All Apps] > [Windows System] > [Control Panel] > [System and
Security] > [Windows Firewall] > [Advanced settings] > [Inbound Rules]
1.2.1
Windows ® 7
Install the software
1. Insert the supplied program CD into the CD drive.
2. Run "view.exe" on the program CD to show the [Setup-VR-7000] dialog box.
3. Click the [Next] button.
4. Confirm that the install location is "C:\Program Files*\FURUNO" then click the [Next] button.
* Folder name for 32 bit. "Program Files(x86)" for 64 bit.
5. Click the [Yes] button.
6. Click the [Next] and [Install] buttons to install the software.
7. After the installation is completed, the message "Yes, restart computer now" is checked. Click the [Finish] button to complete the installation and restart the PC.
Set the IP address and subnet mask
1. Click the [Start] button then click [Control Panel].
2. In the search box, type adapter.
3. Under [Network and Sharing Center], click [View network connections].
4. Right click the connection to change, and then click [Properties].
5. Click the [Networking] tab. Under [This connection uses the following items], click [Internet
Protocol Version 4 (TCP/IP v4)] then click [Properties].
6. Click the [Use the following IP address] button.
2
7. Enter the IP address and subnet mask of the PC:
For data extraction from the DCU
• Port J502 (DATA) of the DCU is connected to port J17:
IP address: 172.31.16.201 or 172.31.16.202
Subnet mask: 255.255.0.0
Note: The IP address of the VR-7000/7000S is 172.31.16.200.
• Port J502 (DATA) of the DCU is connected to port J26:
IP address: 10.0.0.101 or 10.0.0.102
Subnet mask: 255.0.0.0
Note: The IP address of the VR-7000/7000S is 10.0.0.100.
For data extraction from the DRU
IP address: 10.0.0.102 or 10.0.0.99 (other than 10.0.0.140 and 10.0.0.150)
Subnet mask: 255.0.0.0
8. Click the [OK] button and then click the [Close] button.
9. Restart the PC.
1. INSTALLATION
1.2.2
Windows ® 8.1
Install the software
1. Insert the supplied program CD into the CD drive.
2. Run "view.exe" on the program CD to show the [Setup-VR-7000] dialog box.
3. Click the [Next] button.
4. Confirm that the install location is "C:\Program Files*\FURUNO" then click the [Next] button.
* Folder name for 32 bit. "Program Files(x86)" for 64 bit.
5. Click the [Yes] button.
6. Click the [Next] and [Install] buttons to install the software.
7. After the installation is completed, the message "Yes, restart computer now" is checked. Click the [Finish] button to complete the installation and restart the PC.
Set the IP address and subnet mask
1. Move the mouse cursor to the bottom or top right corner of the screen and select the cog icon for [Settings].
2. Select [Control Panel].
3. In the [Control Panel] window, select [Category] and then select Large or Small icons.
4. Select [Network and Sharing Center].
5. Select [Change adapter settings].
6. Right click on your connected network and select [Properties].
7. Select [Internet Protocol Version 4 (TCP/IP v4)] then click [Properties].
8. Click the [Use the following IP address] button.
3
1. INSTALLATION
9. Enter the IP address and subnet mask of the PC:
For data extraction from the DCU
• Port J502 (DATA) of the DCU is connected to port J17:
IP address: 172.31.16.201 or 172.31.16.202
Subnet mask: 255.255.0.0
Note: The IP address of the VR-7000/7000S is 172.31.16.200.
• Port J502 (DATA) of the DCU is connected to port J26:
IP address: 10.0.0.101 or 10.0.0.102
Subnet mask: 255.0.0.0
Note: The IP address of the VR-7000/7000S is 10.0.0.100.
For data extraction from the DRU
IP address: 10.0.0.102 or 10.0.0.99 (other than 10.0.0.140 and 10.0.0.150)
Subnet mask: 255.0.0.0
10. Click the [OK] button and then click the [Close] button.
11. Restart the PC.
1.2.3
Windows ® 10
Install the software
1. Insert the supplied program CD into the CD drive.
2. Run "view.exe" on the program CD to show the [Setup-VR-7000] dialog box.
3. Click the [Next] button.
4. Confirm that the install location is “C:\Program Files(x86)\FURUNO” then click the [Next] button.
5. Click the [Yes] button.
6. Click the [Next] and [Install] buttons to install the software.
7. After the installation is completed, the message “Yes, restart computer now” is checked. Click the [Finish] button to complete the installation and restart the PC.
Set the IP address and subnet mask
1. Right-click on the icon in the bottom-left corner of the screen to open the [Quick Access] menu.
2. Click the [Control Panel] option on the [Quick Access] menu to open the [Control Panel].
3. In the [Control Panel] window, select [Category] and then select Large or Small icons.
4. Select [Network and Sharing Center].
5. Select [Change adapter settings].
6. Right click on your connected network and select [Properties].
7. Select [Internet Protocol Version 4 (TCP/IP v4)] then click [Properties].
8. Click the [Use the following IP address] button.
4
9. Enter the IP address and subnet mask of the PC.
For data extraction from the DCU
• Port J502 (DATA) of the DCU is connected to port J17:
IP address: 172.31.16.201 or 172.31.16.202
Subnet mask: 255.255.0.0
Note: The IP address of the VR-7000/7000S is 172.31.16.200.
• Port J502 (DATA) of the DCU is connected to port J26:
IP address: 10.0.0.101 or 10.0.0.102
Subnet mask: 255.0.0.0
Note: The IP address of the VR-7000/7000S is 10.0.0.100.
For data extraction from the DRU
IP address: 10.0.0.102 or 10.0.0.99 (other than 10.0.0.140 and 10.0.0.150)
Subnet mask: 255.0.0.0
10. Click the [OK] button and then click it again on the next screen.
11. Restart the PC.
1. INSTALLATION
1.3
How to Start the Live Player V5
Select the Live Player V5 program version according to the VDR program version. When the Live
Player V5 program version is not compatible with the VDR program version, the Live Player V5 does not work properly.
• When the VDR program version is “01.20” or later:
Use the latest version of the Live Player V5 ([Live Player V5 ( uu .
uu )] ( uu .
uu : 01.20 or later)).
• When the VDR program version is “01.10” or earlier:
Use the Live Player V5 version 01.10 ([Live Player V5 OLD (01.10)]).
How to start the latest version of the Live Player V5
• Windows
®
7 : [Start] button > [All Programs] > [VR-7000] > [Live Player V5 ( uu .
uu )] ( uu .
uu :
01.20 or later)
• Windows
®
8.1
: [Start] screen > Right click a blank part of screen then select [All Apps] > click
“VR-7000” > [Live Player V5 ( uu .
uu )] ( uu .
uu : 01.20 or later)
• Windows ® 10 : [Start] menu > [All Apps] > [VR-7000] > [Live Player V5 ( uu .
uu )] ( uu .
uu : 01.20 or later)
How to start the Live Player V5 version 01.10
• Windows ® 7 : [Start] button > [All Programs] > [VR-7000 Previous Version] > [Live Player V5
OLD (01.10)]
• Windows
®
8.1
: [Start] screen > Right click a blank part of screen then select [All Apps] > click
[VR-7000 Previous Version] > [Live Player V5 OLD (01.10)]
• Windows
®
10 : [Start] menu > [All Apps] > [VR-7000 Previous Version] > [Live Player V5 OLD
(01.10)]
5
1. INSTALLATION
Note 1: When one of the following symptoms occurs, reboot the Live Player V5.
• A Java
®
related error occurs and Live Player V5 shuts down.
• The Live Player V5 shuts down when maximizing or minimizing a dialog box.
• The track list does not appear (source selected from [Source Select] window; [Analyze] button clicked) after several minutes.
Note 2: If the PC requests a restart while the Live Player V5 is starting up, restart the PC.
Note 3: If there is audio or video in Live play, activate [Network Interface Select] checkbox on the
[Source Select] dialog box, then select the LAN port that is connected with the VR-7000/S.
1.4
How to Uninstall the Live Player V5
Login as the administrator to uninstall the Live Player V5.
1.4.1
Windows
®
7
1. Click [Start] button > [Control Panel] > [Programs] > [Programs and Features].
2. Select “VR-7000” then click [Uninstall].
3. Delete the VR-7000 folder saved in the [My Computer] > [Local Disk (C:)] > [Program
Files*\FURUNO] folder.
* Folder name for 32 bit. "Program Files(x86)" for 64 bit.
1.4.2
Windows
®
8.1
1. Hover the cursor in the bottom-left corner of the screen until a small image of the Start Screen appears, then right-click on the icon to open the [Start Context] menu. Select [Programs and
Features] menu then [Select Programs and Features].
2. Select “VR-7000” then click [Uninstall].
3. Delete the VR-7000 folder saved in the [My Computer] > [Local Disk (C:)] > [Program
Files*\FURUNO] folder.
* Folder name for 32 bit. "Program Files(x86)" for 64 bit.
1.4.3
Windows
®
10
1. Click on the icon in the bottom-left corner of the screen, then select the [Settings] menu. Click the [System] menu then the [Apps & features].
2. Select “VR-7000” then click [Uninstall].
3. Delete the VR-7000 folder saved in the [My Computer] > [Local Disk (C:)] > [Program
Files(x86)\FURUNO] folder.
6
advertisement