Circular Beacon Installation. Carmanah R820-E, R829-E, R920-E, R247-E, F series, R829-F, E Series, R920-F
Add to My manuals75 Pages
advertisement
![Circular Beacon Installation. Carmanah R820-E, R829-E, R920-E, R247-E, F series, R829-F, E Series, R920-F | Manualzz Circular Beacon Installation. Carmanah R820-E, R829-E, R920-E, R247-E, F series, R829-F, E Series, R920-F | Manualzz](http://s3.manualzz.com/store/data/065078878_1-df0b8670eea0229e6bd2fbd94d1f36dc-360x466.png)
4.2 Circular Beacon Installation
E / F SERIES USER MANUAL
4.0 FIXTURE, PUSH BUTTON, & BATTERY INSTALLATION
The E and F Series provides standard wiring to support up to four circular beacons.
1. Thread the flashing beacon harness through the beacon arms. Then, mount the top flashing beacon arm to the pole using stainless banding or bolts (not supplied). Use the gasket on the top mounting arm to ensure water doesn’t leak past the connection and enter the signal head from the top.
Nut and gasket are inside signal head
2. Connect the flashing beacon harness to the terminal block inside beacon housing according to the wire connection table below. Complete the flashing beacon assembly and attach the bottom arm mount to the pole using stainless steel banding or bolts (not supplied).
Carmanah Technologies Corp. | 250 Bay St, Victoria, BC V9A 3K5, Canada | 1.250.380.0052 | [email protected]
| carmanahtraffic.com
35
advertisement
Related manuals
advertisement
Table of contents
- 2 Table of Contents
- 4 1.0 Warnings and Precautions
- 4 Warranty Disclaimer
- 4 Standards
- 4 Safety and Usage Precautions
- 6 System Components
- 7 2.0 Introduction
- 7 About the E and F Series
- 8 Radio Communication
- 8 R920-E and R920-F: Pedestrian Crosswalk with RRFB Light Bars
- 10 R820-E and R820-F: Pedestrian Crosswalk with Circular Beacons
- 11 R829-E and R829-F: School Zone Flashing Beacon
- 12 R247-E and R247-F: 24-Hour Flashing Beacon
- 13 RRFB Light Bars: Overview
- 13 Circular Beacons: Overview
- 14 LED Enhanced Signs: Overview
- 14 Third-Party Devices: Overview
- 16 3.0 Solar Engine Installation
- 16 Tools and Materials Required
- 17 Solar Engine Mounting to Round Post
- 18 Solar Engine Mounting to Square Post with Universal Cast Mount
- 19 Solar Engine Mounting to Square Post with Steel Mount
- 20 Solar Engine Mounting to Side of Post
- 21 Reinforced Signal Head for Integrated Solar Engine / Signal Head
- 22 Integrated Solar Engine with Signal Head – Round Post
- 24 Integrated Solar Engine with Signal Head – Square Steel Post
- 26 Integrated Solar Engine with Signal Head – Square Wood Post
- 28 Integrated Solar Engine with Signal Head – Side of Post
- 30 4.0 Fixture, Push Button, & Battery Installation
- 30 RRFB Light Bar Installation
- 35 Circular Beacon Installation
- 36 LED Enhanced Sign Installation
- 37 Push Button Installation
- 39 Battery Installation
- 43 5.0 Installation of Optional Accessories
- 43 Calendar Upload / Override Switch Kit Installation
- 44 RTC Time Switch Installation (F Series only)
- 45 Information Display Company Time Switch Installation (F Series only)
- 46 Applied Information or FCU Modem Kit Installation (F Series only)
- 48 3PD Time Switch Supplementary Information
- 50 DC Relay Kit Installation (F Series only)
- 51 Polara XAV Controller Kit Installation (F Series only)
- 52 Campbell Guardian Audible Push Button Kit Installation (F Series only)
- 52 6.0 Energy Management System Programming and Testing
- 52 EMS On-Board User Interface Operation
- 65 R920-E/F Programming
- 65 R820-E/F Programming
- 65 R829-E/F Programming
- 65 R247-E/F Programming
- 66 7.0 Commissioning Checklist
- 67 8.0 Maintenance and Product Care
- 67 Fuse Replacement
- 68 Battery Replacement
- 68 EMS Replacement
- 70 EMS Recycling
- 71 9.0 Troubleshooting
- 72 BIST Error Codes
- 74 10.0 Customer Service and Warranty
- 74 Additional Products
- 75 Glossary