advertisement
BOB’S SPACE RACERS
®
WHAC-A-MOLE® SE ARCADE MANUAL BSR V3.0
COIL BED SERVICING
The coil bed is the assembly that houses the solenoids, score sensors and Whac-A-Mole® heads.
This unit is built as an assembly to make servicing and repair easy. The entire unit removes from the game as a sub-assembly in just a couple of minutes.
SHAFT CLEANING
Procedure 1
A quick fix for a Shaft that is sluggish
Procedure 2
Cleaning Shafts without removing them from the game unit
This procedure should be performed every 2 weeks
Procedure 3
Removing Whac-A-Mole® Heads for cleaning
This procedure should be performed every 3 months or less if required
Procedure 1 Instructions
A quick fix for a Shaft that is sluggish
Spray the Shaft with an all purpose Silicone Lubricant.
Note: Do not use graphite spray. It is conductive and you could short out the electrical wiring
and/or the Printed Circuit Board (PCB).
14
BOB’S SPACE RACERS
®
WHAC-A-MOLE® SE ARCADE MANUAL BSR V3.0
Procedure 2 Instructions
Cleaning Mole Head Shafts without removing them from the game unit
1
. Open the front of the game unit for access
3. Remove the clip using a short flathead screwdriver.
3. Remove the washers from the shaft.
4. Lift the Mole Head out of the unit. 5. Remove the 3 washers from the top of the shaft.
5. Clean the shaft using a soft cloth.
Use an electrical contact / anti corrosion cleaner such as ElectriCorr VPCL
– 239 or equivalent.Polish the shaft with Scotch bright.Remove any rust spots with an emery
cloth.
7. Reassemble the shaft in the reverse order.
15
BOB’S SPACE RACERS
®
WHAC-A-MOLE® SE ARCADE MANUAL BSR V3.0
Procedure 3 Instructions
Removing Mole Heads for cleaning
1. Turn off the A.C. power to the game.
2. Remove the 2 bolts that attach the playfield to the top of the main cabinet.
3. Lift the playfield up and pull forward to remove it from the unit.
4. Remove the 4 bolts and washers (7/16”) that secure the coil bed to the cabinet.
5. Remove the coil bed assembly by carefully lifting it up.
16
BOB’S SPACE RACERS
®
WHAC-A-MOLE® SE ARCADE MANUAL BSR V3.0
6. Disconnect the two Molex connectors that are connected to the coil bed assembly.
WARNING!
REMOVE WITH CARE. SENSORS
ARE EASILY BROKEN!!!!!
7. Remove the clip using needle nose pliers or a small screwdriver.
* Make note of the order of the washers on the
top and bottom of the shaft.
8. Remove Mole Head from the Assembly by pulling it out and then remove the 3 washers from the shaft.
9. Spray the shaft with Dry Graphite Lubricant.
Clean the shaft using a soft cloth and an electrical contact / anti corrosion cleaner such as ElectriCorr
VPCL
– 239 or equivalent.
Polish the shaft with Scotch bright
Remove any rust spots with an emery cloth.
10. Clean the bore in the assembly with a gun cleaning kit. *Gun cleaning kits can be purchased at a local
Wal-Mart store.
17
BOB’S SPACE RACERS
®
WHAC-A-MOLE® SE ARCADE MANUAL BSR V3.0
11. Reassemble the washers on the top part of the 12. Insert the shaft into the assembly. shaft. *Note the correct order
13. Reassembly the washers. Note the correct order
Snap the clip back in place.
Repeat these steps for each of the Mole Head shafts
14. Return the coil bed assembly to the game
Plug in the Molex plug connectors.
15. Secure the coil bed assembly to the unit using the 4 bolts and washers.
16. Return the playfield area to the unit and attach the 2 bolts.
18
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 2 MODEL VIEW
- 3 SPECIFICATIONS
- 3 Rated power supply
- 3 Power consumption
- 3 Dimensions
- 3 Weight
- 4 INTRODUCTION
- 4 Overview
- 4 Features
- 4 GAME PLAY
- 5 INFORMATION
- 5 SET UP
- 6 PACKAGE CONTENTS
- 7 INSTALLATION
- 7 Play zone (Operation Zone)
- 7 Locations to avoid
- 8 GAME LEVELING
- 10 INSTRUCTION FOR PLAY
- 10 PROGRAMMING OPTIONS
- 10 Steps for Programming
- 11 Programming Chart
- 12 INSPECTION
- 12 Maintenance
- 13 Cleaning
- 13 TEST MODE
- 13 ERROR CODES
- 14 COIL BED SERVICING
- 14 SHAFT CLEANING
- 19 TROUBLESHOOTING
- 20 Troubleshooting Chart
- 21 REPAIR
- 21 Power Supply Servicing
- 21 and Relay Servicing
- 22 Solenoid Replacement
- 23 BALLAST REPLACEMENT
- 23 Score Display Removal
- 24 Replacement
- 24 PARTS LIST
- 28 WARRANTY