- No category
advertisement
4
1 General safety and application information
This documentation has been produced with the greatest of care and extensively and repeatedly checked. For reasons of clarity, not all the detailed information on all types of the product and also not every imaginable case of erection, operation or maintenance have been taken into account. If you require further information or if specific problems which are not dealt with extensively enough in the documentation exist, you can request the necessary information via the local representation of the company of
BONFIGLIOLI.
We would also point out that the contents of this documentation are not part of a previous or existing agreement, assurance or legal relationship and are not intended to amend the same. All obligations of the manufacturer result from the underlying purchase contract, which also contains the complete and solely valid warranty regulation. These contractual warranty provisions are neither extended nor limited by the production of this documentation.
The manufacturer reserves the right to correct or amend the contents and the product information as well as omissions without prior notification and assumes no kind of liability for damage, injuries or expenditure to be put down to the aforementioned reasons.
1.1
General information
Warning! BONFIGLIOLI VECTRON frequency inverters have high voltage levels during operating, depending on their protection class, drive moving parts and have hot surfaces.
In the event of inadmissible removal of the necessary covers, improper use, wrong installation or operation, there is the risk of serious damage to persons or property.
To avoid the damage, only qualified staff may carry out the transport, installation, setup or maintenance work required. Comply with the s EN
50178, IEC 60364 (Cenelec HD 384 or DIN VDE 0100), IEC 60664-1
(Cenelec HD 625 or VDE 0110-1), BGV A2 (VBG 4) and national provisions. Qualified persons within the meaning of this principal safety information are people acquainted with the erection, fitting, commissioning and operating of frequency inverters and the possible hazards and in possession of qualifications matching their activities.
1.2
Proper use
Warning! The frequency inverters are electrical drive components intended for installation in industrial plant or machines. Commissioning and start of intended operation are not allowed until it has been established that the machine corresponds to the provisions of the EC machine directive
98/37/EEC and EN 60204. According to the CE sign, the frequency inverters additionally fulfill the requirements of the low-voltage directive
73/23/EEC and the s EN 50178 / DIN VDE 0160 and EN 61800-2. Responsibility for compliance with the EMC directive 89/336/EEC is with the user.
Frequency inverters are available in a limited way and as components exclusively intended for professional use within the meaning of the EN
61000-3-2.
With the issue of the UL according to UL508c, the requirements of the
CSA Standard C22.2-No. 14-95 have also been fulfilled.
The technical data and the information on connection and ambient conditions the rating plate and the documentation be complied with. The instructions must have been read and understood before starting work at the device.
4 06/05
06/05
advertisement
Related manuals
advertisement
Table of contents
- 6 General safety and application information
- 6 General information
- 6 Proper use
- 7 Transport and storage
- 7 Handling and positioning
- 7 Electrical connection
- 7 Operation information
- 7 Maintenance and service
- 8 Introduction
- 9 Assembly of the Profibus-DP communication module CM-PDP
- 10 Socket occupancy/bus termination/line
- 11 Baud rate setting/line length
- 11 Setting station address
- 11 Setting PPO type
- 12 Configuration process on the DP master
- 13 Commands SYNC / FREEZE
- 13 Available objects / scanning times
- 15 10 Handling of the objects
- 15 Communication channel
- 16 10.1.1 Order identification
- 16 10.1.2 Reply identification
- 16 10.1.3 Fault messages
- 17 10.1.4 Parameters, data set selection and cyclic writing
- 18 10.1.5 Sequence of communication
- 19 10.1.6 Examples of communication
- 21 Process data channel PZD1/PZD
- 21 10.2.1 PZD1, control word / state word
- 22 10.2.2 Control via contacts
- 23 10.2.3 Control via state machine
- 26 Behavior in quick stop
- 26 Behavior in transition
- 27 10.2.4 Control via remote contacts
- 29 10.2.5 PZD2, reference value / actual value
- 30 10.2.6 Variable actual value reporting via PZD2 in PPO1 / PPO
- 32 10.2.7 Actual value report PZD2 to PZD6 in PPO2 / PPO
- 32 10.2.8 PPO-Out data as global sources
- 37 Actual value display of Profibus data
- 39 11 Parameter list
- 39 Actual value
- 39 Parameter
- 40 12 Annex
- 40 Warning messages
- 40 Fault messages
- 41 GSD File – VEC_0696.GSD