advertisement
Programming 27
Command 965 - Set Up Domestic Dialling Format
Command 965 has been added to make the set up of the Domestic Dialling Format a one step operation. Refer to page 78 for more information on "Domestic Reporting".
After Installer's Programming Mode has been accessed, enter command
965
followed by the
#
button. This will automatically set the following locations in bold below. No other locations will be altered when command 965 has been issued.
Location
Location 49
Location 50
Location 52 - 55
Location 460 - 467
Location 468 - 471
Location 484 - 487
Location 488 - 491
Location 504 - 505
Location 506 - 513
Description
Handshake Tone
Transmission Format
Subscriber ID Number
Location 340 - 347
Zone 1
Location 348 - 355
Zone 2
Location 356 - 363
Zone 3
Location 364 - 371
Zone 4
Location 372 - 379
Zone 5
Location 380 - 387
Zone 6
Location 388 - 395
Zone 7
Location 396 - 403
Zone 8
Location 404 - 411
Zone 9
Location 412 - 419
Zone 10
Location 420 - 427
Zone 11
Location 428 - 435
Zone 12
Location 436 - 443
Zone 13
Location 444 - 451
Zone 14
Location 452 - 459
Zone 15
Zone 16
Bypass Reports
Location 472 - 475
Trouble Reports
Location 476 - 479
Codepad Duress
Location 480 - 483
Codepad Panic
Codepad Tamper
AC Fail
Location 492 - 495
Low Battery
Location 496 - 499
Program Altered
Location 500 - 503
Sensor Watch
Open/Close Reports
Test Report Time
Setting
2 (1400 Hz)
11 (Domestic Dialling)
0, 0, 0, 1
2, 0, 0, 0, 0, 3, 0, 1 (Delay-1)
1, 0, 0, 0, 0, 3, 0, 1 (Handover)
1, 0, 0, 0, 0, 3, 0, 1 (Handover)
1, 0, 0, 0, 0, 3, 0, 1 (Handover)
1, 0, 0, 0, 0, 3, 0, 1 (Handover)
0, 0, 0, 0, 0, 3, 0, 1 (Instant)
0, 0, 0, 0, 0, 3, 0, 1 (Instant)
12, 0, 0, 0, 0, 3, 3, 1 (24 Hour Burglary)
0, 0, 0, 0, 0, 3, 0, 1 (Instant)
0, 0, 0, 0, 0, 3, 0, 1 (Instant)
0, 0, 0, 0, 0, 3, 0, 1 (Instant)
0, 0, 0, 0, 0, 3, 0, 1 (Instant)
0, 0, 0, 0, 0, 3, 0, 1 (Instant)
0, 0, 0, 0, 0, 3, 0, 1 (Instant)
0, 0, 0, 0, 0, 3, 0, 1 (Instant)
0, 0, 0, 0, 0, 3, 0, 1 (Instant)
0, 0, 0, 0 (Not Used)
0, 0, 0, 0 (Not Used)
0, 0, 0, 0 (Not Used)
0, 0, 0, 0 (Not Used)
0, 0, 0, 0 (Not Used)
0, 0, 0, 0 (Not Used)
0, 0, 0, 0 (Not Used)
0, 0, 0, 0 (Not Used)
0, 0, 0, 0 (Not Used)
0, 0 (Not Used)
0, 0, 0, 0, 0, 0, 9, 0 (Not Used)
Table 5: Command 965 Defaults
As you can see from the table above, all reporting other than zone alarms have been disabled. The handshake tone has been set for 1400 Hz tone acknowledgment and the Subscriber ID Number has been set for one identification beep. The zone reporting has been set so that any zone that triggers into alarm condition will only report when the alarm occurs, the zone restore report will not report as there is no separate indications for zone alarm reports and zone alarm restore reports.
Note: From Software Version 1.30, Command 965 disables zone restore reports.
Electronics Design & Manufacturing Pty Limited ISSUE210.DOC
advertisement
Related manuals
advertisement