LTRT-31902 AudioCodes Mediant 1000 MSBG with Microsoft Lync and Verizon SIP Trunk Configuration Note
Add to my manuals102 Pages
advertisement
Configuration Note
1.6
1. Components Information
Lync Server 2010 Specification
For the purposes of this testing, the following server specification was used to host the
Microsoft Lync environment in a fully functioning Lync Server 2010 deployment, including Active Directory and DNS.
The Domain Controller (DC) and t he Lync standard edition where installed on the
OSN3 server hosted on the Mediant 1000B MSBG chassis.
Table 1-5: OSN3 Specifications
Parameter
CPU
RAM Memory
Hard Drives
Bus/Chipset
L2 Cache
Interfaces
Operating
System
Specification
Intel® Core™ 2 Duo 1.5 GHz processors L7400 with Intel 3100
Chipset (64-bit)
2 G DDR2 with ECC
Up to 2 hard drives (HDMX modules) 160GB
64 Bit
2 M
Gigabit Ethernet
USB 2.0 via Connection Module
RS-232 COM
Windows Server 2008 standard
Version 6.2 13 April 2012
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 11 Components Information
- 11 AudioCodes Gateway Version
- 11 Verizon SIP Trunking Version
- 11 Microsoft Lync Server 2010 Version
- 12 Mediation Server Version
- 12 Microsoft Lync Client Version
- 13 Lync Server 2010 Specification
- 14 Topology
- 15 Configuring Lync Server
- 15 Configuring the Mediant 1000 MSBG as a 'IP/PSTN Gateway
- 19 Associating the ‘IP/PSTN Gateway’ with the Mediation Server
- 24 Configuring the ‘Route’ on the Lync Server
- 33 Configuring the ‘Dial Plan’ on the Lync Server
- 38 Enabling Voice Mail in the Exchange Server
- 43 Enabling User for Lync Voice
- 47 Configuring AudioCodes Gateway
- 49 Step 1: Configuring IP Addresses
- 49 LAN and WAN Interface Separation
- 50 Configuring the LAN IP Addresses
- 52 Assigning WAN IP Addresses
- 53 Single LAN Interface
- 55 Step 2: Enabling the SIP SBC and IP2IP Application
- 56 Step 3: Configuring the Number of Media Channels
- 57 Step 4: Configuring the Proxy Sets
- 59 Step 5: Configuring the IP Groups
- 62 Step 6: Configuring the Voice Coders
- 64 Step 7: Defining Silence Suppression and Comfort Noise
- 65 Step 8: Configuring IP Profile Settings
- 68 Step 9: Configuring Message Manipulation for Call Forwarding
- 70 Assigning Inbound Message Manipulation Set to Entire Gateway
- 71 Assigning Outbound Message Manipulation Set to an IP Group
- 72 Step 10: Configuring Unscreened ANI using P-Asserted Identity
- 73 Step 11: Configuring IP-to-IP Routing Setup
- 73 Configure Inbound IP Routing
- 75 Configuring Outbound IP Routing
- 77 Step 12: Configuring Number Manipulation
- 78 Configuring Destination Phone Number Manipulation
- 79 Configuring Source Phone Number Manipulation
- 80 Configuring Redirect Number Manipulation
- 81 Step 13: Configuring SIP General Parameters
- 83 Step 14: Configuring SIP Supplementary Services
- 84 Step 15: Defining Reasons for Alternative Routing
- 86 Step 16: Supporting Regional Call Progress Tone
- 89 Troubleshooting
- 89 Debugging Procedures
- 89 Case Reporting Procedures
- 90 Syslog
- 92 Wireshark Network Sniffer
- 96 Verifying Firmware
- 97 Configuring Analog Devices (ATA’s)
- 97 Step 1: Configure the Endpoint Phone Number Table
- 98 Step 2: Configure Tel to IP Routing Table
- 99 Step 3: Configure Coders Table