LTRT-31902 AudioCodes Mediant 1000 MSBG with Microsoft Lync and Verizon SIP Trunk Configuration Note
Add to my manuals102 Pages
advertisement
3.1.1.2
Lync Server 2010 and Verizon SIP Trunk
Assigning WAN IP Addresses
This section describes how to assign the WAN IP addresses.
To assign a WAN IP address:
1.
Cable the MSBG device to the WAN network (i.e., ADSL or Cable modem), using the WAN port.
2.
Access the MSBG device's Web interface with the Voice and Management IP address.
3.
Access the 'Settings' page (Configuration tab > Data menu > WAN Access >
Settings
tab).
Figure 3-6: Configuring the WAN IP Address
4.
From the 'Connection Type' drop-down list, select the required connection type for the WAN, and then configure the IP address (e.g., 195.189.192.138).
To assign a WAN interface for VoIP traffic:
1.
Select the WAN interface.
2.
Open the 'Multiple Interface Table' page (Configuration tab > VoIP menu >
Network
sub-menu > IP Settings).
Figure 3-7: Selecting WAN Interface for VoIP Traffic in Multiple Interface Table Page
3.
From the 'WAN Interface Name' drop-down list, select the WAN interface for VoIP traffic.
4.
Click Done, and then reset the MSBG device for your setting to take effect.
Configuration Note 52 Document #: LTRT-31902
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 11 Components Information
- 11 AudioCodes Gateway Version
- 11 Verizon SIP Trunking Version
- 11 Microsoft Lync Server 2010 Version
- 12 Mediation Server Version
- 12 Microsoft Lync Client Version
- 13 Lync Server 2010 Specification
- 14 Topology
- 15 Configuring Lync Server
- 15 Configuring the Mediant 1000 MSBG as a 'IP/PSTN Gateway
- 19 Associating the ‘IP/PSTN Gateway’ with the Mediation Server
- 24 Configuring the ‘Route’ on the Lync Server
- 33 Configuring the ‘Dial Plan’ on the Lync Server
- 38 Enabling Voice Mail in the Exchange Server
- 43 Enabling User for Lync Voice
- 47 Configuring AudioCodes Gateway
- 49 Step 1: Configuring IP Addresses
- 49 LAN and WAN Interface Separation
- 50 Configuring the LAN IP Addresses
- 52 Assigning WAN IP Addresses
- 53 Single LAN Interface
- 55 Step 2: Enabling the SIP SBC and IP2IP Application
- 56 Step 3: Configuring the Number of Media Channels
- 57 Step 4: Configuring the Proxy Sets
- 59 Step 5: Configuring the IP Groups
- 62 Step 6: Configuring the Voice Coders
- 64 Step 7: Defining Silence Suppression and Comfort Noise
- 65 Step 8: Configuring IP Profile Settings
- 68 Step 9: Configuring Message Manipulation for Call Forwarding
- 70 Assigning Inbound Message Manipulation Set to Entire Gateway
- 71 Assigning Outbound Message Manipulation Set to an IP Group
- 72 Step 10: Configuring Unscreened ANI using P-Asserted Identity
- 73 Step 11: Configuring IP-to-IP Routing Setup
- 73 Configure Inbound IP Routing
- 75 Configuring Outbound IP Routing
- 77 Step 12: Configuring Number Manipulation
- 78 Configuring Destination Phone Number Manipulation
- 79 Configuring Source Phone Number Manipulation
- 80 Configuring Redirect Number Manipulation
- 81 Step 13: Configuring SIP General Parameters
- 83 Step 14: Configuring SIP Supplementary Services
- 84 Step 15: Defining Reasons for Alternative Routing
- 86 Step 16: Supporting Regional Call Progress Tone
- 89 Troubleshooting
- 89 Debugging Procedures
- 89 Case Reporting Procedures
- 90 Syslog
- 92 Wireshark Network Sniffer
- 96 Verifying Firmware
- 97 Configuring Analog Devices (ATA’s)
- 97 Step 1: Configure the Endpoint Phone Number Table
- 98 Step 2: Configure Tel to IP Routing Table
- 99 Step 3: Configure Coders Table