- Vehicles & accessories
- Motor vehicle electronics
- Car media receivers
- Kenwood
- KVT-M700
- Owner's manual
advertisement
Sound Control Function
Sound Control Menu Screen
M E N U 1 2 : 0 0
S O U N D S E T U P T U N E R
A U D I O S Y S E s
S P S E L
S O U R C E
T O N E
Audio Setting Screen-1
B A L / F A D
F
L
R
R
L O U D
O N O F F
A M P B A S S
F L T
A M P F R E Q
N M L
V . O F F S E T
O F F
A U D I O RTN
Selecting the Audio Setting Screen
Touch the [AUDIO] button.(
☛ Page 14)
You cannot operate when the standby mode is selected.
Selecting the System Es Setting Screen
Touch the [SYS Es] button.(
☛ Page 17)
You cannot operate when the standby mode is selected.
Selecting the Speaker Select Screen
Touch the [SP SEL] button.(
☛ Page 16)
You can operate when the standby mode is selected.
Selecting the Tone Control Screen
Touch the [TONE] button.(
☛ Page 16)
You cannot operate when the standby mode is selected.
Balance and Fader [BAL/FAD]
Touch
[
2]L
[
3]R
[
5]F
[
∞]R
Setting
The sound in the left channel is emphasized.
The sound in the right channel is emphasized.
The sound in the front channel emphasized.
The sound in the rear channel emphasized.
Loudness [LOUD]
Compensating for low and high tones during low volume.
Touch
[
7ON]
[
7OFF]
Setting
Loudness function is turned on
Loudness function is turned off
When the Loudness function is ON, the "LOUD" indicator is
ON in the source control screen.
B.M.S. (Bass Management System) [AMP BASS]
Adjust the bass boost level of the external amplifier using the main unit.
Touch the [
2 ] or [ 3 ] button.
Display Setting
"FLT"
"+6dB"
"+12dB"
"+18dB"
Bass boost level is flat.
Bass boost level is low (+6dB).
Bass boost level is mid (+12dB).
Bass boost level is high (+18dB).
• Refer to the catalog or instruction manual for power amplifiers that can be controlled from this unit.
• For amplifiers there are the model that can be set from Flat to +18 dB, an the model that can be set from Flat to +12 dB.
When and amplifier is connected that can only be set to
+12dB, even if “+18dB” is selected it won’t operate correctly.
B.M.S. Frequency Offset [AMP FREQ]
Setting the central frequency boosted by B.M.S.
Touch the [
2 ] or [ 3 ] button.
Display Setting
"NML"
"LOW"
Boost with the normal central frequency.
Drop the normal central frequency 20%.
Refer to the catalog or instruction manual for power amplifiers that can be controlled from this unit.
14
Audio Setting Screen-2
S Y S T E M Q
T O P 4 0
S Y S T E M Q E x
O N O F F
2 Z O N E
O N O F F
A U D I O RTN
Volume Offset [V OFFSET]
Each source's volume can be set as a difference from the basic volume.
Touch
[
3]
[
2]
Setting
The level is increased.
The level is decreased.
Switching the Audio Setting Screen -1 and 2
Touch the [
2 ] or [ 3 ] button.
System Q [SYSTEM Q]
You can recall the best sound setting preset for different types of the music.
Touch the [
2 ] or [ 3 ] button.
Display Setting
"FLAT"
"ROCK"
"TOP40"
"POPS"
"JAZZ"
"EASY"
"USER"
Flat.
Rock
Top 40
Pops
Jazz
Eaqsy
User memory
• User memory: The values set on the <Tone control screen>
(page 16).
• Each setting value is changed on the <Speaker & Woofer
Setting> (page 18). First, select the Speaker and Woofer type with the <Speaker & Woofer Setting>.
System Q Ex [SYSTEM QEx]
Setting display/don't display for the System Q factors
(Bass center frequency, Bass Q factor, Bass extend,
Middle center frequency, Middle Q factor, and Treble center frequency) in Tone control screen.
Touch
[
7ON]
[
7OFF]
Setting
The System Q factors are displayed.
The System Q factors aren't displayed.
Dual Zone System [2 ZONE]
The following operation allows separate sound sources to control the output of the front and rear speakers.
[
Touch
7ON]
Setting
The dual zone system function is on.
AV-OUT sound send to the rear speaker.
The dual zone system function is off.
[
7OFF]
• When the Dual Zone System is ON, there is no rear channel audio control or other effect.
• When you set the Dual zone system to ON while the nonfading preout is switched ON, the sound of the non-fading preout isn’t output.
Exit the Audio Setting Screen
Touch the [RTN] button.
Return to the sound control menu screen.
15
Sound Control Function
Speaker Select Screen
S P E A K E
6
*
R
9 / 6 i n c h
WO O F E R
1 2 i n t y p e A
Tone Control Screen (Ex:OFF)
B A S S L E V E L
0
M I D L E V E L
2
T R E L E V E L
1
T O N E RTN
S P S E L RTN
Speaker & Woofer Setting
Fine-tuning so that the System Q value is optimal when setting the speaker and woofer type.
Touch the [
2] or [3] button.
In Speaker setting mode [SPEAKER
Display Speaker type
"OFF" Off
"6
*
9/6inch" For 6 & 6x9 inch speaker
"5/4inch" For 5 & 4 inch speaker
"OEM" For the OEM speaker
In Woofer setting mode [WOOFER]
Display Woofer type
"OFF" Off
"12in typeA" 12 inch A type
"10in typeA" 10 inch A type
"12in typeB" 12 inch B type
"10in typeB" 10 inch B type
"12in typeC" 12 inch C type
"10in typeC" 10 inch C type
"8inch" 8 inch type
"12in typeD" 12 inch D type
"10in TypeD 10 inch D type
Exit the Speaker Select Screen
Touch the [RTN] button.
Return to the sound control menu screen.
Tone Control (System QEx set to OFF)
Touch the [
2] or [3] button.
Display Adjustment Item
"BASS LEVEL" Bass level
"MID LEVEL" Middle level
"TRE LEVEL" Treble level
Range
–8 — +8
–8 — +8
–8 — +8
Exit the Tone Control Screen
Touch the [RTN] button.
Return to the sound control menu screen.
16
Tone Control Screen -1 (Ex:ON) System Es Setting Screen
B A S S
1 f
5 0
B A S S E X T
O N O F F
B A S S L
1
E V E L
B A S S
2
Q
. 0 0
T O N E RTN
H P F F
1 2 0
L P F N - F
8 0
H P F R
1 2 0
N - F L E V E L
0 0
N - F P H A S E
N O R M A L R E V E R S E
S Y S T E M E s RTN
Tone Control Screen -2 (Ex:ON)
M I D
1 f
2 0
M I D L E V E L
1
T R E L E V E L
1
M I D Q
2 . 0 0
T R E
1 f
7 .
5
T O N E RTN
Tone Control (System QEx set to ON)
Touch the [
2] or [3] button.
Display Adjustment Item Range
"BASS f" Bass Center Frequency 60/70/80/100 or 150 Hz
"BASS LEVEL"Bass level –8 — +8
"BASS Q" Bass Q Factor 1.00/ 1.25/ 1.50/
2.00
"BASS EXT" Bass Extend
7ON
7OFF
"MID f" Middle Center
Frequency
0.5/1.0/1.5/
2.0kHz
"MID LEVEL" Middle level
"MID Q" Middle Q Factor
–8 — +8
1.00/2.00
"TRE f" Treble Center
Frequency
"TRE LEVEL" Treble level
10.0/12.5/15.0/
17.5 kHz
–8 — +8
• According to the Bass Q Factor setting value, the frequencies that can be set in Bass Center Frequency change as shown below.
Bass Q Factor
1.00/1.25/1.50
2.00
Bass Center Frequency
60/70/80/100 Hz
60/70/80/150 Hz
• When the Bass Extend is set to ON, low frequency response is extended by 20%.
Switching the Tone Control Screen -1 and 2
Touch the [
2 ] or [ 3 ] button.
Exit the Tone Control Screen
Touch the [RTN] button.
Return to the sound control menu screen.
System Es
Touch the [
2] or [3] button.
Display Adjustment Item Range
"HPF F"
"HPF R"
Front High Pass Filter Through/40/60/
80/100/120/150/
180/220 (Hz)
Rear High Pass Filter Through/40/60/
80/100/120/150/
180/220 (Hz)
"LPF N-F"
"N-F LEVEL"
Non-Fading Low Pass 50/80/120/
Filter Through (Hz)
Non-Fading level
"N-F PHASE" Non-Fading Phase
–15 — +15
7NORMAL (0°)/
7REVERSE(180°)
Exit the System Es Screen
Touch the [RTN] button.
Return to the sound control menu screen.
17
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 4 Before Use
- 5 Monitor Control Function
- 8 Menu Function
- 9 Setup Function
- 12 System Setup Function
- 14 Sound Control Function
- 18 (Common operation)
- 20 FM/AM Tuner Control Function
- 23 AV Control Function
- 25 CD Player Control Function
- 26 Disc Changer Control Function
- 28 Name Set Function
- 29 Other Option Control Function
- 34 Remote Control Function
- 36 Installation
- 43 Troubleshooting Guide
- 46 Specifications