- Vehicles & accessories
- Motor vehicle electronics
- Car media receivers
- Kenwood
- KVT-M700
- Owner's manual
advertisement
Remote Control Function
ATT
V.SEL
SRC
38
38
FM+
AM–
DISC
AM
FM
ATT
V.SEL
AV OUT
DIRECT
OK
1
GHI
4
PRS
7
ABC
2
JKL
5
TUV
9
QZ
0
DEF
3
MNO
6
WXY
9
4
TUNE
TRACK
¢
SRC
4
¢
+
–
DIRECT/OK
AV OUT
1 – 0
A – Z
Loading and Replacing the Batteries for the
Remote
2 CAUTION
Do not set the remote on hot places such as above the dashboard.
1. Use two "AAA" batteries.
Slide the cover while pressing downwards to remove it as illustrated.
2. Insert the batteries with the
ª and · poles aligned properly following the illustration inside the case.
Monitor Control Function
3 Switching the Monitor’s Picture
Press the [V.SEL] button.
Each time the button is pressed the monitor’s picture switches.
3 Switching the AV Output Mode
Press the [AV OUT] button.
Each time the button is pressed the AV out mode switches.
Source Control Function (Common operation)
3 Select the Audio Source Mode
Press the [SRC] button.
Each time the button is pressed the audio source switches.
3 Volume
Increasing Volume
Press the [+] button.
Decreasing Volume
Press the [–] button.
3 Attenuator
Press the [ATT] button.
Each time the button is pressed the Attenuator turns
ON or OFF.
FM/AM Tuner Control Function
3 Selecting the FM band
Press the [FM+] button.
3 Selecting the AM band
Press the [AM–] button.
3 Tuning
Press the [
4] or [¢] button.
3 Selecting the Seek Mode
Press the [
38 ] button.
Each time the button is pressed it switches between the AUTO1, AUTO2 and MANUAL seek mode.
3 Recalling Preset Station
Press the [1] – [6] button.
3 Direct Search
1
Press the [DIRECT/OK] button to switch the direct search mode.
2
Press the [0] – [9] buttons and enter the frequency.
Example:
Desired frequency Press button
92.1 MHz (FM)
810 kHz (AM)
[#0], [#9], [#2], [#1]
[#0], [#8], [#1], [#0]
2 WARNING
Store unused batteries out of the reach of children.
Contact a doctor immediately if the battery is accidentally swallowed.
• The provided batteries are intended for use in operation checking, and their service life may be short.
• When the remote controllable distance becomes short, replace both of the batteries with new ones.
34
AV Control Function
3 Selecting the TV band
Press the [FM+] button.
Each time the button is pressed the preset band switches between the TV1 and TV2.
This function available during the KTC-V500N is connected.
3 Selecting the Video
Press the [AM–] button.
Each time the button is pressed the video input switches between the AV IN 1, AV IN2 and RGB.
3 Selecting the Channel
Press the [
4] or [¢] button.
This function available during the KTC-V500N is connected.
3 Recalling Preset Channel
Press the [1] – [8] button.
This function available during the KTC-V500N is connected.
3 Selecting the Seek Mode
Press the [
38] button.
Each time the button is pressed it switches between the AUTO1, AUTO2 and MANUAL seek mode.
This function available during the KTC-V500N is connected.
3 Direct Search
1
Press the [DIRECT/OK] button to switch the direct search mode.
2
Press the [0] – [9] buttons and enter the channel number.
Example:
Desired channel Press button
3 ch
47 ch
[#0], [#3]
[#4], [#7]
This function available during the KTC-V500N is connected.
Disc Control Function
<During the disc changer or player is connected>
3 Pause and play
Press the [
38] button.
Each time the button is pressed it pauses and plays.
3 Track Search
Press the [
4] or [¢] button.
3 Direct Track Search
1
Press the [0] – [9] buttons and enter the track number.
2
Press the [
4] or [¢] button.
3 Album Search (Function of disc changer)
Press the [FM+] or [AM–] button.
3 Direct Album Search (Function of disc
changer)
1
Press the [0] – [9] buttons and enter the disc number.
2
Press the [FM+] or [AM–] button.
SIRIUS Tuner Control Function
<During the KTC-SR901 is connected>
3 Selecting the Preset Band
Press the [FM+] button.
Each time the button is pressed it switches between the SIR1, SIR2, SIR3 and SIR4 preset bands.
3 Selecting the Channel
Press the [
4] or [¢] button.
3 Selecting the Seek Mode
Press the [
38 ] button.
Each time the button is pressed it switches between the SEEK1 and SEEK2.
3 Recalling Preset Channel
Press the [1] – [6] button.
3 Direct Search
1
Press the [DIRECT/OK] button to switch the direct search mode.
2
Press the [0] – [9] buttons and enter the channel number.
2
Press the [
4] or [¢] button.
Weather Band Control Function
<During the KTC-WB100 is connected>
3 Selecting the Channel
Press the [
4] or [¢] button.
35
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 4 Before Use
- 5 Monitor Control Function
- 8 Menu Function
- 9 Setup Function
- 12 System Setup Function
- 14 Sound Control Function
- 18 (Common operation)
- 20 FM/AM Tuner Control Function
- 23 AV Control Function
- 25 CD Player Control Function
- 26 Disc Changer Control Function
- 28 Name Set Function
- 29 Other Option Control Function
- 34 Remote Control Function
- 36 Installation
- 43 Troubleshooting Guide
- 46 Specifications