advertisement
![Testing the System. TracVision A5 | Manualzz Testing the System. TracVision A5 | Manualzz](http://s3.manualzz.com/store/data/022554899_1-baaf763783808b4c006823a3fb1bcab5-360x466.png)
TracVision A5 Installation Guide
4-3 Testing the System
Now all you need to do is turn the system on and ensure everything works properly. Follow the steps below to turn on the TracVision A5 system and verify proper operation.
1.
Ensure that the antenna has a clear view of the satellite. The antenna requires an unobstructed view of the southern sky to receive satellite TV signals. T rees, buildings, highway overpasses, etc., can block satellite signals. Heavy rain or snow might also interrupt satellite signals. For complete details about satellite reception requirements, refer to Section 1-3, “Receiving
Satellite TV Signals,” in the User’s Guide.
Since the TracVision antenna requires an unobstructed view of the southern sky to receive satellite signals, the system will not work when the vehicle is in a garage.
4.6
2.
Apply vehicle power and turn on the vehicle’s entertainment system.
3.
Turn on the TracVision A5 receiver’s rear panel power switch. The switch’s light illuminates and the receiver beeps two or three times.
Receiver Rear Panel Power Switch
Power Switch
POWER
VEHICLE POWER
(10-16 VDC)
SATELLITE IN
RF
REMOTE
INPUT
VHF ANTENNA
IN
OUT TO TV
TUNER
C AU T I O N
AUDIO R AUDIO L VIDEO
TO SATELLITE
IN
S – VIDEO
TO KVH
ANTENNA
PHONE JACK
DIAGNOSTICS
PORT 1
DIAGNOSTICS
PORT 2
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device must not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Tested to comply with FCC Standards
4.
The TracVision antenna searches for and locks onto the satellite. Verify that the following appears on the TV(s):
If your satellite dish is ready for DIRECTV
® service, please wait until your
Advanced Program Guide
™
is prepared.
Installation
Searching for satellite signal...
54-0208-01
The receiver then starts downloading the program guide and the following message appears:
If your satellite dish is ready for DIRECTV
® service, please wait until your
Advanced Program Guide
™
is prepared.
Installation
Acquiring guide data...
This process may take up to 60 seconds. Once the program guide has loaded, a DIRECTV programming channel appears.
5.
If you don’t see the messages shown in Step 4 after 30 seconds, press the remote control’s SAT button. Then press the
PWR button. The receiver beeps twice to indicate that power is applied to the antenna.
PWR
DVD VCR AUX TV SAT
GUIDE
MENU
INFO
FAV
TURBO
O
N
EL
INE GU
ID
E
CLEAR
VOL
SELECT
MUTE
PREV
CH
CH P
A
G
E
54-0208-01
Completing the Installation
Only the DIRECTV ® preview channels (such as channels 100 and 201) are viewable until the user activates the receiver.
6.
Check the three system status lights on the top of the receiver. All three lights should be illuminated green, indicating normal operation. If any of these lights are not green, refer to Section 9-3,
“System Status Lights,” in the User’s Guide for troubleshooting details.
System Status Lights
4.7
advertisement
Related manuals
advertisement
Table of contents
- 12 Using this Manual
- 13 System Overview
- 15 Materials Provided
- 17 Materials You Will Need
- 18 Preparing the Activation Card
- 20 Attaching the Mounting Brackets
- 21 Removing the Shipping Restraints
- 22 Mounting the Antenna - Rack Mount Kit
- 27 Mounting the Antenna - Roof Mount Kit
- 33 Connecting the Antenna Cable
- 39 Measuring the Vehicle’s Height
- 54 Installing the Remote Control Batteries
- 55 Post-installation Checklist
- 57 Testing the System
- 59 Selecting the Proper Time Zone
- 60 Other Components
- 63 Activating the Receiver