advertisement
FIREFINDER
TM
INSTALLATION COMMISSIONING & OPERATION
9 LCD Screen Format
There are 3 events that can be reported and displayed by
Smart Terminal
. The types of event are;
1.
Fire
2.
Faults and
3.
Disables.
The types of events are only associated with sensors and detectors hence faults associated with modules, loops O/C
– S/C, power supplies and so forth are not reported on the LCD.
The
Smart Terminal
has front panel indicators for each type of event. When
Smart Terminal
is configured not to report a type of event and that event type is present (and the corresponding front panel indicator is illuminated on the
Smart Terminal
), then a standard information screen is displayed on the LCD stating the system is not normal and the operator should see the FACP.
Alarm
If configured the screen format for reporting loop / sensor / zone fire condition is:
LCD Line Number Information
1
2
3
4
Device descriptor (up to 33 characters) Type Descriptor (up to 6 characters)
Loop address and zone number(Lxx Syyy.zz Zwww) current device status
Date and Time of occurrence (DD/MM/YYYY HH:MM:SS)
Alarm sequence number ( Device Alarms nnn of nnn)
Fault
If configured the screen format for reporting loop / sensor / zone fault condition is:
LCD Line Number Information
1
2
3
4
Device descriptor (up to 33 characters) Type Descriptor (up to 6 characters)
Loop address and zone number(Lxx Syyy.zz Zwww) current device status
Blank
Fault sequence number ( Device Fault nnn of nnn)
Note: The fault types only relate to devices.
In the event of a loss of communications, for a period of greater than 15 seconds the
Smart Terminal
will default to the No Communications screen. The format for this screen is:
LCD Line Number Information
1
2
3
4
No Communications
Device Isolate / Disables
If configured the screen format for reporting loop / sensor / zone disable condition is:
LCD Line Number Information
1
2
3
4
Device descriptor (up to 33 characters) Type Descriptor (up to 6 characters)
Loop address and zone number(Lxx Syyy.zz Zwww) current device status
Blank
Isolate / Disable sequence number ( Device Fault nnn of nnn)
Pre-alarm
If configured the screen format for reporting loop / sensor / zone Pre-alarm condition is:
LCD Line Number Information
1
2
3
4
Loop address and zone number(Lxx Syyy.zz Zwww)
Pre-alarm descriptor (up to 15 characters)
Line is left blank
Pre-alarm sequence number ( Device Pre-alarms nnn of nnn)
Page 49
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 6 Non Disclosure Agreement
- 7 About This Manual
- 7 Introduction
- 7 General Requirements
- 7 References
- 7 Symbols
- 8 System Overview
- 10 Description
- 12 Placing The Basic System Into Operation
- 12 Unpacking
- 12 Anti-Static Precautions
- 12 Working On The System
- 12 The Cabinet
- 12 Mounting The Cabinet
- 13 Operational Parameters
- 13 Cabling Recommendations
- 14 Power Supplies and AC Mains Installation
- 16 Current Limiter, Fuse Board
- 17 Brigade / PSU Monitor Board
- 19 Brigade / PSU Monitor Board & Battery Connections
- 19 Brigade / PSU Monitor Board Auxiliary 27 Volt Power
- 19 Brigade / PSU Monitor Board DBA / MCP & Door Switch Connections
- 19 Brigade PSU Monitor Board ASE Fault Brigade Box Connection
- 20 Connecting a Bell / Sounder to the Brigade / PSU Monitor Board
- 20 Warning System Connections
- 20 Brigade / PSU Monitor Board Relay Output Connections
- 21 Main Board BRD85MBA
- 22 Front Panel Board
- 24 Main CPU BRD85CPU
- 25 Slave CPU
- 26 RS232 Modem / Programming / Debug Interfacing
- 26 Ancillary Services
- 27 Conventional Zone Board
- 28 Addressable Loop Termination Board
- 29 Boards
- 31 16/16 Input / Output Board
- 32 16 Way Input Board
- 32 Serial Relay Board
- 33 Fire Fan Module BRD25FCB
- 33 Fan Termination Board BRD25FTB
- 34 Zone & General Indicator Card
- 36 Printer
- 36 Indicators and Buttons
- 37 Maintenance
- 38 Printer Connections and Jumpering
- 38 Printer 5 Volt Power Supply ( 302-713 )
- 39 Expanding the System Through Networking
- 39 Communications: Controller Interface Card
- 39 Communications: Network Interface Card
- 40 Expansion Board ( 302-688 )
- 40 Expansion Controller
- 41 Networking
- 43 Liquid Crystal Display Repeater Panel
- 44 Terminal
- 44 Operation
- 44 Access levels
- 45 Specifications
- 45 Overview
- 46 Operational & Key Features
- 46 Mechanical
- 47 Installation & Cabling
- 48 Setting the Address
- 49 Terminal Controller Configuration in ConfigManager
- 49 Terminal Reporting Parameters in ConfigManager
- 50 Terminal Controls
- 52 Terminal Indicators
- 54 LCD Screen Format
- 55 Trouble Shooting Chart
- 56 Agent Release Control
- 56 Operation
- 59 Controlled Access
- 60 Local Control Station
- 63 Agent Release Termination Board BRD25ATB
- 64 Interface Wiring
- 66 Warning Signs
- 68 Occupant Warning Systems
- 73 Brigade Devices
- 73 ASE ( Vic Metro ) Brigade Box
- 73 Brigade Box ( Deltec WA, SA, TAS,QLD )
- 74 Operation
- 74 The Control Panel
- 77 Function And Menu
- 77 The Default LCD Display
- 77 Accessing Functions and Menus
- 77 Function Menu and Access Levels
- 77 Forgotten Passwords
- 78 The Main Menu
- 78 Status Menu
- 80 Testing Menu
- 80 Alarm Test
- 80 Fault Test
- 80 Lamp Test
- 81 Main Functions
- 81 Setting the Function Date Facility
- 81 Setting the Function Time Facility
- 81 Setting the Function Daynight Facility
- 81 Function Logs Facility
- 82 The Function Test Facility
- 83 Function Manual I/O Control
- 83 Function Access ( Level II ) / Passwords ( Level III )
- 84 Function Programming
- 84 Conventional Zone Programming
- 85 Device Programming
- 85 Input Programming
- 85 Output Programming
- 86 Manual Control Point ( MCP )
- 86 Sub Address
- 86 Watchdog
- 86 Self Learn
- 86 Extra Devices Detected
- 87 Mismatch Detected
- 87 Incoming Fire Alarm Signal
- 89 Accessing a Loop, Sensor or Zone
- 89 List of Compatible Devices
- 89 Short Circuit Isolation
- 90 Compatible Devices
- 92 Certification Information
- 93 Statement of Compliance
- 95 Installation Details
- 96 Commissioning Test Report
- 97 Procedure
- 97 System Information
- 101 Troubleshooting Chart
- 102 Address Setting
- 103 Battery Capacity Calculation
- 109 Glossary of Terms
- 110 Definitions
- 111 Quick Reference Guides