Outrun 2 SP SDLX Manual

7

7

PRECAUTIONS WHEN MOVING THE MACHINE

● As used in these instructions, the term “moving” refers to moving of the product within the same building, store or facility. These instructions do not cover moving between different buildings, areas, stores or facilities, since diverse factors are involved, not only packaging but also loading onto transport vehicles, and securing the product in place during transport. To transport the product to a different building or store, contact the vendor where the product was purchased or the office indicated in these instructions. Or request that moving be done for you. This product is made up of parts that are of large size and heavy weight.

Unless work is entrusted to someone with expertise in packaging and transport of such parts, a serious accident might occur.

● Even when the product is to be moved within the same building, store or facility, contact the point of purchase or the office indicated in these instructions if there will be level differences or narrow or low level entrances while moving.

Or request that moving be done for you. Never disassemble the product in any way not covered in these instructions. Otherwise there could be a fire, electric shock and/or short circuit.

● Always disconnect the power cable before moving the product. If it is moved with the power cable connected, the cable could be damaged, causing fire or electric shock.

● A qualified electrician is required for moving product parts within a store and for changing indoor wiring. Do not have work performed by anyone who is not qualified. Otherwise there could be electric shock.

● Have work performed by site maintenance personnel or other qualified individuals. Do not allow people without proper knowledge and technical expertise to work on the product. Otherwise there could be an electric shock or other serious accident. Also, customers could be injured while operating the product.

● Never move the product after it has been assembled. Always take down the billboard, and separate the four cabinets’ cockpit units from the DLPs (with the projector remaining on the DLP base). Moving the product while it is assembled may cause abnormalities in the joints and fastenings, and can result in accidents such as electric shock, short circuit, and fire.

● Because it is structurally difficult for exterior lighting to enter the cabinet, have auxiliary lighting available. Working within a dark environment can lead to accidents.

● For instructions on separation and disassembly of the cabinet, please refer to

Chapter 6 of this manual. Failure to follow the instructions given by this manual leaves a high risk of accidents such as electric shock occurring.

● Proceed with checks and tasks as indicated in these instructions. If instructions are not followed, or if tasks and/or checks are neglected, an electric shock or other very serious accident, even fatal accident, can occur. Also, customers could be injured while operating the product.

● Be careful not to damage wiring. Before separating parts that have wiring connections, disconnect the wiring connections, unravel wire bundles and undo fastenings. Only after that, remove fasteners (screws, nuts, etc.). If wiring becomes damaged, there could be an electric shock, short circuit or fire.

116

● When inserting or removing a connector, always hold it by its main part. If you hold it by anything else while doing so, the connections between wire and connector terminal fixtures could be damaged; and there could be a short circuit or fire. There could also be poor connectivity.

● Do not move unit with the adjusters in contact with the floor. Otherwise parts might be damaged or deformed and there might be accidents.

● Whenever any fasteners (e.g. screws, nuts) have been lost, always use replacement fasteners with proper dimensions as specified in this manual. If fasteners of any other dimensions are used, it could cause damage and/or separation of parts that result in secondary accidents.

● Check surroundings carefully while moving the unit. If you should get caught between the unit and a wall, for instance, there could be a serious accident.

● Do not place the cockpit or DLP on inclines or uneven surfaces. This could result in the unit falling over.

● Have on hand a number of workers appropriate for each task that needs to be done. Make calculations by approximating that one worker can lift roughly 15 kg of weight.

If an insufficient number of workers try to lift a heavy object, it could result in a worker stumbling and the object being dropped, crushing someone or something underneath. Workers could also injure their backs, etc.

● When lifting a heavy object, be sure to carefully consider the area where it will be lifted. If possible, lift the object by its handles or base. If weak fasteners or fragile parts are gripped, they could be damaged under the weight of the object, and this could result in a worker stumbling and the object being dropped, causing personal injury.

● Never disassemble the unit in ways other than those described in this manual.

Doing so can cause accidents such as electric shocks, short circuits, and fires.

● Do not attempt to tilt the unit to fit it through narrow doorways. Moving the unit while it is tilted can result in an accident. It can also cause deformations and damage to parts, as well as deviations of fastening positions, which could result in accidents during operation.

7

● Do not push plastic parts or the ride’s FRP parts. Do not support the unit by carrying plastic parts or FRP parts. Parts can be damaged, and fragments can cause injury.

● Do not stack parts that have been separated or disassembled indiscriminately.

The surface of the parts could be damaged or deformed. Significant deformations can result in improper operation and breakdowns.

● Do not lean separated or disassembled parts against a wall or other surface indiscriminately. The parts could be deformed. Accidents could also occur should the parts fall over.

● Do not hold or push controls such as the steering wheels or Gear Shifters.

Deformations could lead to player injury.

117

7

● If the unit is moved over floor surfaces where there is carpet, decorative panel, etc., there might be friction or soiling.

● Movement by casters can damage the floor, depending on the floor material.

Have a mat or thin plate available for moving casters. If rugs, for instance, have been laid out, remove them before moving.

● Be careful not to damage the surfaces of parts. Support and push strong parts made of metal.

● Do not apply rope directly to the product’s surface. Use protective material at locations where rope is applied.

The strength of this product’s joints were not designed such that the product can be moved while assembled.

Attempting to push on the cockpit, etc. to move the unit while assembled can result in damage, deformation, and misalignment of the joints. Abnormalities in the joints can result in improper operation or breakdown in internal mechanisms.

FIG. 7a

118

FIG. 7b

7

FIG. 7c

FIG. 7d Moving the control tower

119