advertisement
10
10
STEERING WHEEL MECHANISM
● When working with the product, be sure to turn the power off. Working with the power on may cause an electric shock or short circuit.
● Be careful not to damage the wires. Damaged wires may cause an electric shock, short circuit or present a risk of fire.
● Do not touch any parts that are not specified in these directions. Touching unspecified locations may lead to electric shock or cause short circuits.
● This work should be performed by site maintenance personnel or other skilled professionals. Work performed by non-technical personnel can cause a severe accident such as an electric shock.
● To prevent accidents while working or while operating the product after it has been installed, be sure not to conduct any procedures other than those given in this manual. There are cases in which procedures not covered in this manual require special tools and skills. If a procedure not given in this manual is required, request service from the office given in this manual or from the point of purchase.
● Exercise due caution in performing soldering procedures. If the soldering iron is handled carelessly, there could be fires or burns.
● Proceed very carefully when heating the thermal contraction tube. Careless operations can result in fires or burns.
● The motor parts may be hot immediately after a game has been completed, so allow some time to pass before beginning work on the parts.
● Stand back from the cabinet when restoring power after maintenance has been completed. The ride and steering wheel will automatically undergo initialization operation when power is restored. Failure to move away from the product could result in an accident such as a collision or fall.
● Be careful when handling the parts of the steering wheel mechanism. Avoid damaging, deforming, or losing them. The loss of even one part will adversely affect the operation of the steering wheel, and may cause player injury. It could also result in fatal breakdown or faulty operations.
● Be careful not to get fingers caught when removing or attaching doors or adjusting the VR bracket.
● The handle mechanism has mechanical parts such as gears and timing belts.
Performing maintenance also requires a person to bend over the side of the cockpit. Careless work methods can result in injuries such as back and shoulder injuries, or fingers being caught.
136
advertisement
Related manuals
advertisement
Table of contents
- 6 HANDLING PRECAUTIONS
- 11 PRECAUTIONS REGARDING INSTALLATION LOCATION
- 11 2-1 LIMITATIONS OF USAGE
- 12 2-2 OPERATION AREA
- 13 PRECAUTIONS REGARDING PRODUCT OPERATION
- 13 3-1 BEFORE OPERATION
- 16 3-2 DURING OPERATION (PAYING ATTENTION TO CUSTOMERS)
- 18 3-3 PRECAUTIONS FOR TICKET OPERATION
- 21 3-4 SWITCHING OFF THE POWER
- 22 PART DESCRIPTIONS
- 25 ACCESSORIES
- 29 ASSEMBLY AND INSTALLATION
- 121 PRECAUTIONS WHEN MOVING THE MACHINE
- 125 PROJECTOR
- 126 8-1 CLEANING THE SCREEN
- 127 8-2 PROJECTOR ADJUSTMENT
- 131 8-3 CHANGING THE LAMP UNIT
- 138 LCD MONITOR
- 138 9-1 CLEANING THE MONITOR SURFACE
- 139 9-2 ADJUSTMENT METHOD
- 141 STEERING WHEEL MECHANISM
- 142 10-1 VOLUME ADJUSTMENT AND REPLACEMENT
- 146 10-2 GREASING
- 147 GEAR SHIFTER
- 147 11-1 GEAR SHIFTER REMOVAL
- 148 11-2 SWITCH REPLACEMENT
- 148 11-3 GREASING
- 149 ACCELERATOR & BRAKE
- 149 12-1 VOLUME ADJUSTMENT AND REPLACEMENT
- 152 12-2 GREASING
- 153 COIN SELECTOR
- 155 GREASING THE RIDE MECHANISMS
- 156 14-1 GREASING THE ACTUATOR
- 161 14-2 GREASING THE GUIDE
- 165 FLUORESCENT LIGHT AND LAMP REPLACEMENT
- 170 PERIODIC INSPECTION
- 173 TROUBLESHOOTING
- 177 GAME BOARD
- 178 18-1 REMOVING THE LINDBERGH
- 182 18-2 COMPOSITION OF THE GAME BOARD
- 183 18-3 SOFTWARE INSTALLATION
- 191 DESIGN-RELATED PARTS
- 193 WIRE COLOR CODE TABLE
- 194 WIRING DIAGRAM