advertisement
7.5 Remote diagnostics
(not available in all countries)
The remote diagnostics function is normally switched off. When it is switched on, our service department can access some of your fax machine’s technical data over the telephone line, and can make changes to these if necessary. This is useful in the event of a breakdown and can bring rapid assistance. You will first have to switch the remote diagnostics on. After 24 hours remote diagnostics is automatically blocked again.
FUNCTION
7
∗
1
4
8
0
2
5
9
#
3
6
Select function 41.
OK
OK
Press the OK key.
Select using the CURSOR LEFT or CURSOR RIGHT key, then press the OK key.
41 REMOTE OPER.
FINE PHOTO BUSY TEL TEL/FAX TAM/FAX
REMOTE OPER.:OFF
FINE PHOTO BUSY
4 OTHERS
TEL TEL/FAX TAM/FAX
FINE PHOTO BUSY TEL TEL/FAX TAM/FAX
The remote diagnostics is a very good tool to make changes in the programming of your fax machine. It is however not suitable for making any repairs concerning electrical or mechanical defects.
7.6 Mercury
The two services of Mercury Communications Limited (MCL), the residential 132 and the Pin code service, can be accessed via most existing British Telecom (BT) lines. In case of any doubt ask MCL Customer Assistance
(0500 500 194) which one is available at your location.
Before you can use the Mercury button, function 27 must be set according to the service you have access to.
7.6.1 Mercury Residential 132
In the factory-setting of your fax the Mercury residential 132 service is activated. If you have changed to Mercury
Pin code service please see below how to activate Mercury residential 132 service.
Press the Function key.
FUNCTION NR.: __
FUNCTION
FINE PHOTO BUSY TEL TEL/FAX TAM/FAX
1
4
7
∗
8
0
2
5
9
#
3
6
Enter function number 27.
27 MERCURY
FINE PHOTO BUSY TEL TEL/FAX TAM/FAX
OK
Press the OK key.
MERCURY: 131
FINE PHOTO BUSY TEL TEL/FAX TAM/FAX
OK
Press the CURSOR LEFT or CURSOR RIGHT key.
Press the OK key.
MERCURY: 132
FINE PHOTO BUSY TEL TEL/FAX TAM/FAX
2 COMMUNICATION
FINE PHOTO BUSY TEL TEL/FAX TAM/FAX
– 61 –
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 8 1.1 Preface
- 8 1.2 Conventions
- 8 1.3 Description
- 11 2.1 The proper location
- 12 2.2 Connection
- 16 2.3 Connecting additional devices
- 17 2.4 Connecting to a home telephone system
- 17 2.5 Connecting to a private branch exchange
- 18 2.6 Loading or removing the thermal paper
- 21 2.7 Important settings
- 21 2.7.1 Available functions
- 22 2.7.2 Language of display and reports
- 23 2.7.3 Entering date and time
- 23 2.7.4 Entering your number
- 24 2.7.5 Entering your name
- 25 2.7.6 Correcting wrong entries
- 25 2.7.7 Operating mode
- 26 3.1 Making a call
- 26 3.2 Sending faxes
- 29 3.3 Receiving faxes - different reception modes
- 29 3.3.1 Changing the mode
- 29 3.3.2 Manual reception
- 30 3.3.3 Automatic reception without additional devices
- 33 3.3.4 Automatic reception with additional devices
- 34 3.4 The answering device
- 34 3.4.1 Switching on your answering machine
- 35 3.4.2 Recording your outgoing message
- 36 3.4.3 Listening to messages
- 37 3.4.4 Deleting messages
- 38 3.5 Copying
- 40 4.1 Redial
- 41 4.2 Speed dial
- 41 4.2.1 Storing a speed dial number and name
- 41 4.2.2 Using the speed dial keys
- 42 4.3 Name dial
- 42 4.3.1 Storing names and numbers
- 43 4.3.2 Using name dialling
- 43 4.3.3 Deleting stored entries
- 44 4.4 Speed and name dial list
- 44 4.5 On-hook dialling
- 45 5.1 Improved picture quality
- 45 5.2 Sending a fax during a telephone call
- 46 5.3 Speaking after fax transmission
- 46 5.4 Selective fax reception
- 47 5.5 Polling
- 47 5.6 Faxing to sub-addresses
- 48 5.7 Page header
- 48 5.8 Half-speed transmission
- 49 5.9 Transmission report
- 50 6.1 Adjusting the recording time
- 50 6.2 Automatic forwarding of messages
- 52 6.3 Recording a telephone conversation
- 52 6.4 Breakthrough
- 53 6.5 Recording Memo’s
- 53 6.5.1 External Memo / message for the caller
- 54 6.5.2 Internal Memo / ”Note pad
- 55 6.6 Remote access
- 55 6.6.1 Preparing your fax machine for remote access
- 56 6.6.2 Remote access of the answering machine
- 58 7.1 Call restriction -babysitter setting
- 60 7.2 Type of ring signal
- 60 7.3 Volume of the ring signal
- 60 7.4 Volume of the loudspeaker
- 61 7.5 Remote diagnostics
- 61 7.6 Mercury
- 61 7.6.1 Mercury Residential
- 62 7.6.2 Mercury Pin Code service
- 62 7.6.3 Changing the Mercury Pin Code
- 63 7.6.4 Deleting the Mercury Pin Code
- 63 7.6.5 Using Cost Centre Codes
- 64 7.6.6 Initiating a conversation via MCL service
- 64 7.6.7 Switching the Mercury function off
- 69 9.1 Important information for safe operation
- 70 9.2 Technical specification
- 70 9.3 Customer information
- 71 9.4 Glossary
- 72 9.5 Index