Axis NETWORK CAMERA 2120 User`s manual


Add to my manuals
76 Pages

advertisement

Axis NETWORK CAMERA 2120 User`s manual | Manualzz

AXIS 2120

Network Camera

User’s Manual

2

AXIS 2120 User’s Manual

About This Document

This document is intended for administrators and users of the AXIS 2120 Network Camera, and is applicable for firmware release 2.32. Although many of the operational aspects of the product are described in the on-line help, this manual contains information for configuring, managing and using the unit in your networking environment, as well as a general overview of the product functionality.

Readers are recommended to use this document as a supplement to the Wizards and other online information available via the Web-based interface. Later versions of this document will be posted to the Axis Website, as required.

Safety Notices

Please observe all safety markings when using this product.

Caution! - Potential hazard that can damage the product.

Important! - Potential hazard that can seriously impair operation.

Do not proceed beyond any of the above notices until you have fully understood the implications.

Legal Considerations

Camera surveillance can be prohibited by laws that vary from country to country. Check the laws in your local region before using the AXIS 2120 for surveillance.

Electromagnetic Compatibility (EMC)

USA -

This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart B of Part 15 of FCC rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference, in which case the user at his/her own expense will be required to take whatever measures may be necessary to correct the interference.

Shielded cables should be used with this unit to ensure compliance with the Class A limits.

Liability

Every care has been taken in the preparation of this manual; if you detect any inaccuracies or omissions, please inform your local Axis office which can be found on the cover of this document. Axis Communications AB cannot be held responsible for any technical or typographical errors and reserves the right to make changes to the product and manuals without prior notice. Axis Communications AB makes no warranty of any kind with regard to the material contained within this document, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Axis Communications AB shall not be liable nor responsible for incidental or consequential damages in connection with the furnishing, performance or use of this material.

Trademark Acknowledgments

Acrobat, Adobe, Boa, Ethernet, IBM, Internet Explorer, LAN

Manager, Linux, Macintosh, Microsoft, Netscape Navigator,

OS/2, UNIX, Windows, WWW are registered trademarks of the respective holders. Java and all Java-based trademarks and logos are trademarks or registered trademarks of Sun

Microsystems, Inc. in the United States and other countries.

Axis Communications AB is independent of Sun Microsystems

Inc.

Support Services

Should you require any technical assistance, please contact your local dealer. If your questions cannot be answered immediately, your dealer will forward your queries through the appropriate channels to ensure a rapid response. On-line manuals, technical support, software updates, application software and general corporate information can also be obatined from www.axis.com.

AXIS 2120 User’s Manual

Revision 2.02

Dated: June 2002

Copyright © Axis Communications AB,

1996 - 2002 requirements for radiated emission according to limit B of

EN55022/1994, and the requirements for immunity according to EN55024/1998 residential, commercial, and light industry.

AXIS 2120 User’s Manual Table of Contents

3

Table of Contents

Product Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Features and Benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Physical Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

The Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

The Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Assembling Your Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Checking the Hardware Inventory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Fixing the AXIS 2120 to a Mounting Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Installing Your Camera on a Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Quick Installation Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Verifying the Installation From Your Browser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Installing Your Camera to a Modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Connecting Your Computer Using the Null Modem Cable . . . . . . . . . . . . . . . . . . . . . . 17

Creating a Dial-up Networking Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Refining the Dial-up Networking Properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Initiating the Dial-up Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Verifying the Modem Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Configuring Your Camera. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Configuration Using the Wizards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

The Administration Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

System Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Motion Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Reinstating the Factory Default Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Choosing Your Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Networking Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Modem Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Adjusting the Camera Focus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Direct Focusing in Your Browser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Using the The Focus Assistant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Replacing the Lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Adjusting the DC-Iris Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Adjusting the Back Focus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

The AXIS 2191 Audio Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Features and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

4

Table of Contents AXIS 2120 User’s Manual

Installing the Audio Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Configuring the Audio Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Using the Audio Module with Your Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Technical Specifications for the AXIS 2191 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Appendix A - Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

PINGing Your IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Symptoms, Possible Causes and Remedial Actions . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Appendix B - Other IP Setup Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Using the AXIS IP Installer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Notes for Macintosh Users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Appendix C - Updating the Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Appendix D - The Unit Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Appendix E - High-Speed Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Appendix F - Custom Web Pages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Appendix G - Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Glossary of Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

AXIS 2120 User’s Manual Product Overview

5

Product Overview

The AXIS 2120 is a digital network camera running TCP/IP. It includes all of the required networking connectivity for distributing monitored images over a secure intranet network or the Internet. With its own built-in Web server, the AXIS 2120 provides high-quality imaging, and full Web-based control of the product management and configuration functions through a browser over your network.

Connecting directly to Ethernet or Fast Ethernet networks, the AXIS 2120 is a standalone digital network camera that will also connect to a local Internet Service Provider using an external modem.

To simplify the installation process, the Web-based interface features several interactive

Wizards that provide a seamless and automated integration into your networking and application environments. Its open-network structure minimizes the need for costly and complex coaxial cabling, to offer a cost-effective intranet and Internet imaging solution with minimal installation costs.

6

Product Overview AXIS 2120 User’s Manual

Features and Benefits

Easy to Use -

The AXIS 2120 is completely independent of any other server and requires no other special hardware or software such as PC frame grabber cards or viewing software. All you need is Netscape Navigator 4.x or above. Alternatively, you can use Microsoft Internet

Explorer 4.x or above, together with the Axis ActiveX component. If your computer does not allow you to use ActiveX components, use the Java Applet instead. The AXIS 2120 has complete plug-and-picture functionality - all you need do is assign a valid IP address.

Simple Administration -

Using a standard browser, you configure and manage the AXIS 2120 directly from its own Web pages. Image control, time stamping and text overlays are all accessible from the tools.

Outdoor Use -

The AXIS 2120 has a varifocal DC Iris lens that automatically regulates the amount of light entering the camera, and provides a wide-angle zoom with minimal distortion. With a standard CS-mount, this lens can easily be replaced by any other lens conforming to the same standard. When installed in an appropriate outdoor housing, the

AXIS 2120 is the ideal remote monitoring solution for outdoor use. For sales information on appropriate outdoor casings for the AXIS 2120, please see the product pages for the

AXIS 2120 at www.axis.com.

Motion Detection -

Sophisticated motion detection with in-picture alarm programming, and exclusive multi-window triggering for non-critical remote monitoring.

Wide Range of Applications -

The AXIS 2120 offers live video over internet networks and the

Internet, and is ideal for use with many of today’s high-speed internet services. Allowing remote access directly from your browser, you can view live images, manage and control the AXIS 2120 at any time and anywhere. Use it for intruder detection, process control, industrial and public monitoring, image archiving, or any other application.

Built-in Support for the AXIS 2191 Audio Module -

The AXIS 2120 can be used directly with this add-on component, which enables live audio on your camera. The AXIS 2191 is supplied separately.

Open Standards Environment -

Supporting TCP/IP networking, SMTP e-mail, HTTP and other

Internet-related protocols, the AXIS 2120 can be used in mixed operating system environments such as; Windows, UNIX, Macintosh and OS/2. It integrates easily into other

WWW/Intranet applications and CGI scripts.

Standard Image Format -

The AXIS 2120 delivers complete, high-quality pictures in standard

JPEG format, which can be viewed using any standard browser.

AXIS 2120 User’s Manual Product Overview

Image Updating -

The on-board AXIS ETRAX 100 processor combined with the revolutionary AXIS ARTPEC-1 Real Time Picture Encoder provides an amazing power-synergy to deliver up to 25/30 frames/second (PAL/NTSC) over 10Mbps or 100Mbps networks.

High Compression -

The AXIS ARTPEC chip provides efficient compression of JPEG images and allows the variable compression ratio to be defined by the user.

External Device Connection -

Supporting an auxiliary Input/Output Connector, you can connect your AXIS 2120 to a variety of external devices; such as, IR-sensors, switches and alarm relays. In combination with the programmable alarming facilities, you can quickly develop a variety of security applications that are triggered on time or alarm-based events.

Modem Support -

The Point to Point Protocol (PPP) support allows you to use your AXIS

2120 remotely over a serial link, just as if it were located on your local network. After initially setting up the unit using a local connection to a computer, you can then configure the unit for remote use over an external modem.

ISP Support -

Arrange for image files to be uploaded to an Internet Service Provider (ISP) and you can provide the global Internet community with browser access to your live images. Select any supported ISP from the Web-based Wizards, or choose your own ISP as an imaging repository for your images.

Security -

The AXIS 2120 includes a self-contained Web server, which means that your digital images can be protected just like any other Internet host. Data protection is normally implemented by your Network Administrator using the unit’s security setings in combination with an organization’s Internet firewall. The Administrator can subsequently restrict image access to specific individuals, groups of user, company staff... or make them available to the whole Internet community.

Linux Operating System -

The AXIS 2120 includes modified versions of the Boa Web server, and Linux operating system - both of which are freely distributed under the GNU General

Public License, as published by the Free Software Foundation. This software provides a stable and reliable platform for open-source development of the product.

In accordance with the GNU General Public License, Axis has published the kernel for this product at http://developer.axis.com/.

AXIS Technology -

Axis renowned chipset technology is built upon an open architechture that is streamlined to provide device connectivity independent of any file server. The AXIS

2120 is driven by a powerful AXIS ETRAX 32-bit RISC processor and includes the industry's first dedicated digital video remote monitoring compression chip - the AXIS

ARTPEC-1.

7

8

Physical Description AXIS 2120 User’s Manual

Physical Description

Read the following information to familiarize yourself with the AXIS 2120, making particular note of where the connectors and indicators are located. As a supplement to the information provided in the Quick Installation Guide, this section provides a useful reference when installing the product.

The Front Panel

Status Indicator

Used in conjunction with the Focus Assistant, this multi-colored indicator can be used as a local

focusing aid (see Adjusting the Camera Focus, on page 39). However, under normal conditions,

this indicator defines the operational status of the camera, as described below:

• green - the indicator flashes briefly and momentarily displays orange during the start-up and self-test routines; the indicator then displays green to indicate a healthy unit status.

• red - the indicator will display red only if a problem with the AXIS 2120 has occurred. Refer

to Appendix A - Troubleshooting.

Note: The Status Indicator also displays orange when resetting to the factory default settings, as

described in Reinstating the Factory Default Settings, on page 28. The Status Indicator can also be

made to flash whenever images are displayed in a browser. See the on-line help for more information.

Control Button

Located to the left of the lens assembly; this button is recessed within the product casing. Using a suitably pointed object, press this button to restore the factory default settings

as described in Reinstating

the Factory Default Set-

tings, on page 28; and to

enable the Focus Assis-

tant, as described in

Adjusting the Camera

Focus, on page 39.

Lens Assembly

Includes a wide angle lens with rotational focus control.

The supplied lens is removable and can be replaced with any standard C/CS- mounted lens.

Serial Number

Located on the underside label of the AXIS

2120, the serial number is identical to the

Ethernet address of the unit.

Caution!

Although the AXIS 2120 Network Camera is supplied with a varifocal DC auto-Iris lens that automatically regulates the amount of light into the camera, prolonged exposure to direct sunlight or halogen light may damage the CCD. Consequently, Axis recommends extreme caution when installing your product in strong sunlight, as failure to do so may invalidate your product warranty.

AXIS 2120 User’s Manual Physical Description

The Rear Panel

RS-232 Serial

Connector

The serial connector provides the RS-232 interface for connecting a modem, or the connection for the AXIS 2191

Audio Module. For pinout

information, see Appendix D -

The Unit Connectors.

Power Supply

Connector

A single Jack socket

(PS-D) for connection of the AXIS 2120 power supply. The terminal block connector provides an auxiliary connection point for

AC or DC power to the unit.

Power Indicator

Normally lit when power is applied. If it is not lit, or it flashes, there is a problem with the AXIS 2120 external power supply.

I/O Connector

Provides the physical interface to a digital output, and a single digital photo-coupled input that is used for connecting a variety of external alarm devices to the AXIS

2120 including, IR-sensors, switches and alarm relays. In combination with the configurable alarm facilities, you can quickly develop a variety of security applications that are triggered on time - or alarm based - events. The connector can also be utilized as an alternative connection point for DC power to the unit. For pinout infor-

mation, refer to Appendix D - The Unit Connectors.

Network Connector

The AXIS 2120 is designed for

10 Mbps Ethernet and 100

Mbps Fast Ethernet networks and connects to the network via a twisted pair category 5 cable (10baseT and

100baseTX), terminated using a standard RJ-45 connector.

Supporting NWAY, the AXIS

2120 detects the speed of the local network segment and varies the speed of data communication accordingly

(between 10 Mbps and 100

Mbps)..

DC-Iris Connector

With the DC-Iris cable connected to the lens upon delivery, this socket provides the power and electronic signalling to the lens of the AXIS 2120.

For instructions on how to change the DC Iris settings,

refer to Adjusting the

DC-Iris Settings, on page

Network Indicator

After completion of the startup and self test routines, this multi-colored indicator flashes independently, as follows:

• yellow - activity on a 10Mbps network

• green - activity on a 100Mbps network

• red - no physical connection to the network

9

Note:

The power supply for your AXIS 2120 is country specific. Please check that you are using the cor-

rect type. See page 10.

10

Assembling Your Camera AXIS 2120 User’s Manual

Assembling Your Camera

The information provided in this section will assist you in unpacking and assembling the product correctly. Once assembled, you are then ready to install and configure your product, as described in the following sections of this document.

Checking the Hardware Inventory

Unpack and check all the items against the itemized list below. You should contact your dealer immediately if you find anything is missing or damaged.

Item

Network Camera

Null Modem Cable

Mounting Assembly

Power Supply (PS-D)

PS-D Extension Cable

Printed Materials

Disk Media

Title/Variants

AXIS 2120 50 HZ (without power supply)

AXIS 2120 50 HZ Europe

AXIS 2120 50 HZ UK

AXIS 2120 50 HZ Australia

AXIS 2120 60 HZ (without power supply)

AXIS 2120 60 HZ Europe

AXIS 2120 60 HZ US

-

-

AXIS 2120 60 HZ Japan

AXIS 2120 60 HZ Australia

Europe

UK

Australia

USA

Japan

3.3 meter

AXIS 2120 Installation Guide v1.0 (or later)

Product Warranty Document

AXIS Network Camera CD v1.2 (or later)

Part Numbers

0126-001-01

0126-002-01

0126-003-01

0126-006-01

0126-011-01

0126-012-01

0126-014-01

0126-015-01

0126-016-01

16954

15104

14233

14234

14255

14253

14254

15187

17618

18489

-

Important!

To accommodate the different power supply frequencies found in the USA and Europe, the AXIS 2120 is available in 60Hz and 50Hz variants.

The 60Hz variant delivers a resolution of 525 lines of at 60 half-frames per second and is suitable for use in the United States; whereas the 50Hz variant delivers 625 lines at 50 half-frames per second and is appropriate for use in Europe.

AXIS 2120 User’s Manual Assembling Your Camera

Fixing the AXIS 2120 to a Mounting Assembly

Caution!

Although the AXIS 2120 Network Camera is supplied with a varifocal DC auto-Iris lens that automatically regulates the amount of light entering the camera, prolonged exposure to direct sunlight or halogen light may cause damage to the CCD.

Consequently, Axis recommends extreme caution when installing your product in strong sunlight, as failure to do so may invalidate your product warranty.

The mounting assembly supplied with your AXIS 2120 features a screw head that attaches to the underside of the product. Fasten the AXIS 2120 to the mounting assembly and position it appropriately for your application. The three holes in the base unit allow the product to be securely fastened to a wall.

11

12

Installing Your Camera on a Network AXIS 2120 User’s Manual

Installing Your Camera on a Network

• Macintosh users - Please refer to Notes for Macintosh Users, on page 61.

• Easy installation - Use The AXIS IP Installer. See Using the AXIS IP Installer, on page 60.

• Quick installation- Follow the instructions below to install the AXIS 2120 on an Ethernet network.

Important!

• For details on how to install the AXIS 2120 to a modem, see Installing Your Camera to a Modem, on page 15.

• If you are using your AXIS 2120 in an outdoor application, the unit must be housed in an outdoor enclosure.

Please see the Axis Website at: www.axis.com for details of suppliers.

• Do not use the default or IP address featured in the following examples when installing your AXIS 2120.

Acquire an unused IP address from your Network Administrator.

• Server Privileges: Although no special privileges are required for Windows 95/98/ME, you do need Administra-

tor privileges for Windows NT/2000, and Root privileges on UNIX.

Quick Installation Procedure

Follow the instructions below to quickly install the AXIS 2120 onto an Ethernet network:

Note the Serial number

Note the Serial number on the underside of the unit. You need to know this to set the IP address:

Serial number same as

Ethernet address; e.g.

00408c100086 =

00-40-8c-10-00-86

Assign an IP Address

Using an appropriate method for your operating system, assign your AXIS 2120 with a unique IP address from a computer on your network, using the ARP command, as follows:

Windows only - Start a Command prompt and type these commands:

UNIX only - Type these commands in your command line:

Syntax:

Syntax: arp -s <Camera IP address> <Ethernet address> <my PC IP address> ping -t <Camera IP address> arp -s <IP address> <Ethernet address> temp ping <IP address>

Example:

Example: arp -s 172.21.1.200 00-40-8c-10-00-86 172.21.1.193

ping -t 172.21.1.200 arp -s 172.21.1.200 00:40:8c:10:00:86 temp ping 172.21.1.200

AXIS 2120 User’s Manual Installing Your Camera on a Network

You will now see ‘

Request timed out...

messages repeatedly returned in the window.

Notes:

•In Windows you can find out the IP address of your workstation by running

winipcfg

(Win

95/98/ME) or

ipconfig

(Win NT/2000) from the command line.

•See also Other IP Setup Methods, on page 59.

13

Connect an Ethernet cable to your AXIS 2120 and attach it to the network.

Attach the external Power Supply to the unit and connect it to your local mains supply.

Approximately 10-15 seconds after connecting the power supply, the message ‘

Reply from 172.21.1.200...

- or similar, is returned in the Command Prompt. Ensure that the

Power Indicator is permanently lit and that the Network Indicator flashes intermittently.

Exit ping. The installation is complete, and you are now ready to access the AXIS 2120 from your Web browser, as described in the next section.

Power Indicator

Network Indicator

14

Installing Your Camera on a Network AXIS 2120 User’s Manual

Verifying the Installation From Your Browser

Having completed the installation procedure above, you should then verify the connection between the AXIS 2120 and the network, as follows:

1. Start your browser (see note below) and enter the name or IP address in the

Location/Address field:

Example!

http://172.21.1.200/

The

Home Page for your AXIS 2120 is now displayed:

Installation Wizard and

Administration Tools

2. Continue the setup and basic configuration using the Installation Wizard or

Administration Tools, as described in Configuring Your Camera, on page 21.

Important!

To enable the updating of images in Microsoft Internet Explorer, you must set your browser to allow ActiveX controls and perform a once-only installation of the Axis ActiveX component onto your workstation. However, if your computer environment restricts or prohibits the installation of additional software components, you can alternatively set your AXIS 2120 to use a Java applet for updating the images. This is done from the Image settings in the Administration Tools.

AXIS 2120 User’s Manual Installing Your Camera to a Modem

15

Installing Your Camera to a Modem

The information in this section describes how to connect the AXIS 2120 to a serial modem for transmitting images over a normal Dial-up connection.

Before You Begin

Before you can set up and access a modem-connected AXIS 2120 from a browser, you must first create a local connection to it. This connection is only required for the initial setup, and can be created using the network or the supplied Null Modem Cable.

Using the Network

The easiest and best way to configure the camera for use with a modem is to first install it

onto a local network, if one is available. See Installing Your Camera on a Network, on page

12 for more information. You can then use the Wizards and Administration tools to

configure the modem connection and the application.

Using the Null Modem Cable

When there is no network available, the alternative is to connect a local computer to the

AXIS 2120 using the supplied Null Modem Cable. You then create a Dial-up connection and establish the basic settings, using the Wizards and Administration Tools. See the following pages for more information. This type of connection is only a temporary solution that provides initial access to the camera. Once you have set up the camera for modem access, then all configuration can be done via the modem connection instead and you will not need to use the cable again.

Important!

Please note that the Null Modem Cable is only intended for the initial configuration of modem applications when there is no Ethernet Network available. It is not possible to use the cable as a serial connection for using the AXIS 2120 as a "web camera".

Quick Start For Advanced Users:

Follow these abbreviated instructions if you are experienced with Windows Dial-up

Networking:

1. Connect the camera to the Ethernet Network if available, and use a browser to open the

IP-address you set for your AXIS 2120. Proceed to step 5. If no network is available, use the Null Modem Cable and proceed to step 2.

2. Set up an existing session to 115.200 bps, using the physical COM-port to which you have connected your AXIS 2120.

16

Installing Your Camera to a Modem AXIS 2120 User’s Manual

3. Login with the username root and the password pass. The Phone Number and Modem

Type that you enter are irrelevant at login and you can use dummy numbers for completing these dialogs.

4. Start your Dial-up Networking session and enter any URL containing a period; the

AXIS 2120 emulates a DNS server and will respond to this regardless.

5. Start the Installation Wizard and Administration Tools to further configure the

product, as described in Configuring Your Camera, on page 21.

AXIS 2120 User’s Manual Installing Your Camera to a Modem

Connecting Your Computer Using the Null Modem Cable

Important!

• The information and screen examples featured here are specific to Windows NT. Although similar to the dial-up procedures in other Windows versions, small deviations in the dialog instructions for other operating systems should be expected. Refer to your system documentation for further information on creating a dial-up modem connection if you are using any other operating system.

• Windows dial-up Networking and TCP/IP must be correctly installed prior to commencing with the modem cable connection. Detailed information on how to check this is provided in Windows Help.

Follow the steps below to configure a serial modem connection for your AXIS 2120:

Connect the supplied Null modem cable between the Serial Connector on the AXIS 2120 and the serial port on your computer.

From the Start menu, open the

Control Panel and double-click the

Modems icon.

Connect the power supply to the camera server and check that the Power

Indicator is lit.

If a Standard Modem is already set up and displayed in the Modem Properties dialog (see right) proceed directly to step 8.

17

Check the checkbox:

Don’t detect my modem, I will select it

from a list. Click Next>.

Select the Standard 28800 modem from the displayed list of modems. Click Next>.

A Standard 28800 modem connection is now available for the AXIS 2120. Click Finish to close the Install New Modem

Wizard.

Select the serial port to which your AXIS 2120 is now connected via the Null

Modem cable. Click

Next>.

Click

Close.

Click the Properties button to finally check that the displayed Communications Port is set correctly; that is, set to the same port as you have connected the AXIS

2120. Click OK.

18

Installing Your Camera to a Modem AXIS 2120 User’s Manual

Creating a Dial-up Networking Connection

Follow the steps below to create a dial-up networking connection to your AXIS 2120:

Double-click My Computer and then double-click the Dial-Up

Networking icon.

Double-click the Make New

Connection icon.

Provide the connection with a name (AxisCamera is the name used in the subsequent examples).

From the drop down dialog, select the Standard Modem previously created for the AXIS

2120 as the selected device.

Click

Configure...

To significantly improve the performance of your AXIS 2120 when using the Null Modem cable, set the Maximum

Speed to 115200.

Click OK and then click

Next>.

The telephone numbers requested in the following dialog are not required for use in the logical connection to your camera. To bypass the wizard error correction, simply enter any dummy number into the Area

code, Telephone number and Country code fields. Click Next>.

You have now successfully created your dedicated dial-up networking connection for your AXIS 2120. Click

Finish.

The new dial-up network connection is displayed. You are now ready to refine the dial-up networking properties, as described in the next section...

AXIS 2120 User’s Manual Installing Your Camera to a Modem

Refining the Dial-up Networking Properties

Having created the dial-up connection for your AXIS 2120, follow the steps below to refine the connection properties:

From the dial-up networking dialog, right-click the dedicated dial-up connection previously created for your camera (AxisCamera was the connection used in this and previous examples). Select

Properties.

Click TCP/IP settings and then check the

Server assigned IP address, and Server

assigned name server addresses radio buttons.

19

Click the Server Types tab. From the drop-down list, select PPP as the Type of Dial-Up Server.

In the Advanced options field, check

Enable software compression. All other checkboxes should remain unchecked.

Check the Use IP header compres-

sion and Use default gateway on a

remote network checkboxes. Click OK.

In the Allowed network protocols field, check the TCP/IP checkbox. The NetBEUI and

IPX/SPX checkboxes should remain unchecked.

Click the Scripting tag and ensure that the Start ter-

minal screen minimized checkbox is checked. Click OK to exit Dial-Up Networking Properties.

20

Installing Your Camera to a Modem AXIS 2120 User’s Manual

Initiating the Dial-up Connection

Important!

Please ensure that the Null Modem Cable is correctly installed and that the connection properties are correctly configured prior to initiating a Dial-up connection. Instructions on how to do this are provided on the preceding pages of this section.

Double-click My Computer and then double-click the Dial-Up Networking dialog.

Double-click the dial-up connection icon previously created for your

AXIS 2120. AxisCamera was used in this and previous examples.

Enter a Username and Password, using the default root and pass respectively.

Click Connect to initiate the dial-up connection.

Verifying the Modem Connection

Having initiated your dial-up connection as described above, you can quickly verify the integrity of the connection by accessing the AXIS 2120 using a standard browser, such as

Netscape or Internet Explorer, as follows:

As the AXIS 2120 emulates a DNS server, type in any URL containing a period in the Location/Site field of your browser to display the AXIS 2120 Home Page.

abc.xyz

Now configure the unit using the Installation

Wizard or the Administration Tools.

AXIS 2120 User’s Manual Configuring Your Camera

21

Configuring Your Camera

Important!

Javascript must be enabled in your Web browser for the AXIS 2120 Web-based interface to work.

Before You Begin

Successful installation of the product is prerequisite to configuring the unit; therefore, it is recommended that you read the following information before commencing with this section:

Choosing Your Application, on page 29, and then...

Installing Your Camera on a Network, on page 12, ...or

Installing Your Camera to a Modem, on page 15.

Having chosen the type of application you want to develop and having installed the product accordingly, your AXIS 2120 will now be attached directly to a local area network,

or connected to a PC using the supplied Null Modem Cable. You are now ready to proceed with the unit’s configuration.

This section describes how to use the Wizards for configuring and integrating the AXIS

2120 into your application environment, and provides a general overview of the

Web-based Administration Tools.

Configuration Using the Wizards

For speedy development of your application, the AXIS 2120 supports two easy-to-use

Wizards that are recommended for both novice and advanced users alike. Depending upon your choice of application, the Installation Wizard and the Application Wizard can be run either consecutively, or independently of one another.

Important!

• When accessing the Administrator Tools for the first time during a session, you will be assumed to be the administrator and will be logged in as such, with the username root and default password pass.

• You must change the root password as soon as possible. Until this has been done, the security features in the product be will not be enabled. Furthermore, all Axis products are shipped with the same

password by default. For further information, refer to System Security, on page 25.

• Prior to accessing the Installation Wizard or Administration Tools over a network, you must first set

the Internet address, as described in Installing Your Camera on a Network, on page 12.

22

Configuring Your Camera AXIS 2120 User’s Manual

Installation Wizard Overview

The Installation Wizard provides a quick and easy way to define the System, Security,

Image and Layout settings for your application - as described in the Tools Overview, on page 24.

Starting the Installation Wizard

1. With reference to the information provided in the On-line Help , click the

Installation Wizard from the AXIS 2120 Home Page and then follow the Wizard to complete the configuration.

2. Click the Finish button to save the defined application settings to the product.

Application Wizard Overview

The Application Wizard can be started from the final page of the Installation Wizard, or started independently from the Administration Tools - Wizards page. It provides a quick and easy way to define the Operation and Layout settings for your application - as

described in Tools Overview, on page 24.

Starting the Application Wizard

1. With reference to the operation information provided in the On-line Help , click

Continue... within the Application Wizard or click the link from within the

Administration Tools - Wizards Page to start the Wizard.

2. Click the Finish button to save the defined application settings to the camera.

The Administration Tools

Whether you are viewing images directly over the network or transmitting images over a modem, you can use the Web-based Administration Tools for configuring and managing your AXIS 2120 at any time. Used for reviewing and refining your configuration after initially setting up the AXIS 2120 with the Installation Wizard, these tools are ideal for more advanced users.

Note:

On-line help is stored internally in the AXIS 2120 and is available from most pages within the AXIS 2120 Web interface. Containing comprehensive details on all product parameters and

Administration Tools, the on-line help is your first point of reference when configuring and managing the unit, and is particularly useful for resolving any administration queries.

AXIS 2120 User’s Manual Configuring Your Camera

Accessing the Tools

1. Start your browser and enter the name or Internet address of the AXIS 2120 (or any

DNS name if you are accessing the unit via the Null Modem Cable) in the address field.

Example!

http://172.21.1.200/

2. The AXIS 2120 Home page is now displayed. Click Administration Tools.

23

3. The Administration Tools are now presented as links in the margin of the Administration

Page. Simply click the relevant link for the parameters you want to configure.

As an Administrator, you configure and modify the system directly from this page.

24

Configuring Your Camera AXIS 2120 User’s Manual

Tools Overview

The table below provides a one-stop overview of the Administration Tools:

Settings

Image

Tool Description

Focus the camera using the Focus Assistant, adjust the Auto Iris settings, and define image attributes for your

AXIS 2120.

Network

System

External

Devices

Applications

Operation

Motion

Detection

Layout

Wizards

Installation

Configure the TCP/IP and SMTP E-mail network settings.

Set the product Date and Time, create and delete Users and passwords, and change the Administrator’s password.

By default, the AXIS 2120 supports anonymous user access, which means that anybody on the Internet/intranet has access to the video images from a Web browser. To restrict open access, simply register a single authorized user.

Set the COM-Port on the AXIS 2120 to use a modem or the AXIS 2191 Audio Module, which is supplied separately.

For information on how to configure and use the audio module, please s ee The AXIS 2191 Audio Module, on page

45.

Tool Description

Choose to run your AXIS 2120 in Sequential or Alarm Mode; determine when and how often images are taken using the Scheduler; and define when the images are uploaded to an ISP, or target FTP/Web server.

Enable in-picture motion detection and trigger an immediate alarm whenever significant movement occurs in the picture area. Create a single motion detection window for the whole image area, or create up to three discrete drag-and-drop windows and restrict alarms to movement in specific areas. Each motion detection window is assigned with a unique name, and a set of profile sliders that allow you to set individual alarm thresholds for the

Size, History, and Sensitivity parameters.

A Motion Indicator is also included, to provide an immediate visual display of actual detected motion against the defined alarm thresholds that are established for the highlighted window.

Determine the Layout for the Web page in which your images will appear. Customize the page to your own design and include your own logos, links and title texts, and enable or disable specific function buttons.

Tool Description

The Installation Wizard helps you quickly get the product up and running. Recommended for use by both novices and experienced users.

Application This Wizard will guide you through the process of setting up your application.

Support

General

Tool Description

Displays various useful information about how and where to get help.

Release Notes View the product Release Notes, the Parameter List, and/or initiate a Restart of the unit.

Parameters Displays the complete list of settings currently valid in the unit.

Log File Displays the log file showing all of the commands executed since the last restart.

Restart/ Reset Provides commands for restarting the unit and for resetting to the factory default settings.

About Displays information about the development of this product.

Help

Home

Starts the product’s on-line help

Opens the product’s home page.

AXIS 2120 User’s Manual Configuring Your Camera

System Security

To prevent any unauthorized use of the camera, the AXIS 2120 supports multi-user password protection and access is restricted to defined users only. The system

Administrator(s) has exclusive access to the product’s Administration Tools and can determine the registration and access rights for all users.

Notes:

•When accessing the Administrator Tools for the first time, you will be assumed to be the administrator and will be logged in as such, with the username root and default password pass.

•The root password must, however, be changed as soon as possible. Until this has been done, the security features in the product be will not be enabled. Furthermore, all Axis products are shipped with the same password by default. Close and restart your browser to complete the operation.

User Access Rights

As an Administrator, click System - Users to perform any of the following tasks:

• define or edit the

administrator (root) password

• define, add and delete

user names and passwords

• assign individual access rights for selected users, where each user is awarded one or all of the following levels of access:

-

Admin: a user granted with Admin rights has exclusive access to the product Administration

Tools and can consequently determine the registration of all users.

-

Dial-in: provides the user with dial-in modem access only to the AXIS 2120.

- View: provides the lowest level of access, which allows the user to view the images only.

Specifying at least one such user will disallow all other anonymous access.

Important!

By default, the AXIS 2120 supports anonymous user access, which means that anybody on the Internet/intranet has access to the video images from a browser.

To restrict open access, simply register a single authorized user. This effectively disables the anonymous user service and restricts camera access to specified users. If the anonymous user service is satisfactory for your application, simply do not add any users. The Administrator’s own settings are enough to provide anonymous viewing access.

25

26

Configuring Your Camera AXIS 2120 User’s Manual

Motion Detection

The AXIS 2120 includes in-image motion detection that comprises multi-window support for up to three motion detection windows in the target image area.

Use the motion detection feature to generate an alarm whenever movement occurs in the image area. You can create a single window for monitoring the whole surveillance scene, or create three smaller windows for targeting specific areas within the image area. All movement outside the defined motion detection window is ignored.

You can create up to three motion detection windows, and move, resize, or delete any window at any time. Furthermore, the behavior for each motion detection window can be defined by adjusting the Size, History, and Sensitivity profile sliders for each window. The user interface for this function is very easy to use.

Important!

The video motion detection algorithm in the AXIS 2120 is specifically designed for non-critical remote monitoring applications, and consequently Axis advises against using this product for critical surveillance usage - where reliable motion detection must be assured at all times.

Axis does not accept liability for any incidents of unwarranted triggering or failure of the product’s motion detection function - spurious, occasional, or otherwise.

AXIS 2120 User’s Manual Configuring Your Camera

Creating a Motion Detection Window

Follow the instructions below to create a motion detection window within the image area:

1. Click the New button to open a standard-sized window; or click and drag the mouse from within the image area to create a motion detection window of any size.

2. Drag and drop the new window to any area you wish to monitor. The motion detection window can be resized by dragging the bottom-right corner.

3. To configure the window, provide it with a name in the Name field, and adjust the

Size, History, and Sensitivity profile sliders accordingly for the monitored area. A full description of each profile slider is provided in the table below.

4. The Motion Indicator will now display the current level of motion, with the threshold value for alarm settings represented by a black colored delimiter bar. An alarm is only generated if the motion exceeds the tolerance defined by the delimiter bar. The indicator displays red whenever enough motion occurs to trigger an alarm.

Profile Slider Parameter

Size

Description

Defines how large a moving object must be to trigger the motion detection - relative to the size of the defined motion detection window. For example; when monitoring a landscape, setting the size parameter to small might possibly trigger the motion detection each time a bird flies through the motion detection window.

The ‘size’ profile slider is used to determine the minimum size of the triggering object within the motion detection window.

History Defines the elapsed time duration between the comparable reference and the current images; i.e. should your AXIS 2120 compare the latest image with the one taken previously (Low level), or against one taken over an hour ago (High level)?

A High level setting causes the reference image to be updated very infrequently; consequently, any significant change in the target image will initiate an alarm that is active for a long period of time. A

Low level setting causes the reference image to be updated very frequently; consequently, any significant object in the target image area will be active for only a very short period, before being seen as identical to the updated reference image.

This parameter is useful for 24 hour monitoring when night turns to day, and other occasions when you want slight deviations in the motion detection window area to be tolerated without initiating alarms.

Sensitivity Defines how subtle the change of color, or nuance, needs to be before a motion detection alarm is triggered.

Ordinary colored objects on ordinary backgrounds trigger the motion detection when this parameter is set to High level. When set to a Low level, only very bright objects on a dark background will trigger the motion detection.

Deleting a Motion Detection Window

To delete a window, simply click the X in the upper right-hand corner of the window.

Alternatively, select the window you wish to delete and press the Delete button.

27

28

Configuring Your Camera AXIS 2120 User’s Manual

Reinstating the Factory Default Settings

In certain circumstances, it may be necessary to reinstate the Factory Default settings for your AXIS 2120. This is performed by clicking the Support link in the Administration

Tools, and then selecting Restart/Reset, or by pressing the Control Button. Follow the instructions below to reinstate the product factory default settings using the Control button:

1. Switch off the AXIS 2120 by disconnecting the power cable.

2. Press and keep the Control Button pressed, and then reconnect the power supply cable.

3. Keep the Control Button pressed until the Status Indicator displays yellow (note that this may take up to 15 seconds), then release the button. When the Status Indicator displays green (which can take up to 1 minute) the AXIS 2120 will then have been reset to the original factory default settings.

Notes:

•Reinstating the factory default settings will cause all parameters (including the IP address) to be reset.

•Refer to Installing Your Camera on a Network, on page 12 for information on how to set the IP

address in the product.

AXIS 2120 User’s Manual Choosing Your Application

29

Choosing Your Application

The AXIS 2120 can be used in a wide variety of applications and installs directly onto an

Ethernet network, or it can be used with a V.90-compatible modem. Using the Web-based

Administration Tools and easy-to-use Wizards, you can quickly and easily develop your application.

Not to be regarded as a comprehensive catalog of possible user applications, this section describes several typical applications and includes other information to help you configure the camera.

Note:

Although most V.90-compatible modems are known to work well with the AXIS 2120, Axis does not guarantee that the product will work with all modems conforming, or otherwise, to the same standard.

Networking Applications

If you have access to an Ethernet connection at your chosen point of installation, all you need to do is attach the AXIS 2120 to your LAN/WAN and set the IP Address. Then you are ready to view images from any desktop over your network.

However, the AXIS 2120 offers more than just convenient access to live images over the network. Using the available Wizards to guide you through the process, you can quickly configure your product for a variety of exciting applications, including:

• Viewing images in a custom-designed Web page.

• Uploading images to a remote FTP server on a LAN/WAN network to accommodate a large audience where a high volume of Web page hits is anticipated.

• Motion detection or external alarm device triggering - with uploading of pre and/or post alarm images to a target FTP server, when in-image motion, external alarms, or time-based events occur. You can also optionally send e-mail alerts containing a single image, or a Web link to a pre/post alarm image sequence stream saved to the target FTP server.

Note:

You can access live images from any desktop browser on your network as soon as the AXIS 2120 is physically installed on your network. The installer of the camera uses the available Wizards to configure the chosen application. Advanced users can then use the Web-based Administration

Tools for refining the application once the basic configuration has been established with the Wizards.

30

Choosing Your Application AXIS 2120 User’s Manual

Picture frequency for Networking Applications

When used in a TCP/IP networking environment, the AXIS 2120 delivers up to 25/30

(PAL/NTSC) images/second; where the actual image frequency is typically limited by:

• your computer and browser

• the chosen image resolution and compression

• the lighting conditions at the point of installation

• available network bandwidth

• the complexity of detail and color variation within the image

Important!

60Hz and 50Hz variants of the AXIS 2120 are available to accommodate the different power supply frequencies found in the USA and Europe.

The 60Hz variant delivers a resolution of 525 lines at 60 half-frames per second and is suitable for use in the United States; whereas, the 50Hz variant delivers 625 lines at 50 half-frames per second and is appropriate for use in Europe.

Image Compression Ratios

Although the file size of a JPEG-compressed image depends upon the actual content of the image, images containing a lot of detail generally generate larger files. Image quality is largely controlled by the level of compression; where high compression yields small files, and low compression maintains higher image quality at the expense of larger files. The table below is derived from real-life tests, and defines the average file sizes for each supported image resolution:

Resolution

4CIF (704 x 480) **

60Hz (NTSC Countries)

Filesize (kb)

7 - 150

CIF (352 x 240) 1.4 - 40

Max fps*

10

30

50 Hz (PAL Countries)

Resolution

4CIF (704 x 576) **

Filesize (kb)

8.5 - 180

CIF (352 x 288) 1.7 - 50

Max fps*

8

25

* Maximum performance for a single viewing client.

** Interlaced image

Note:

Using a modern computer will avoid introducing any unnecessary constraints on the imaging frequency.

AXIS 2120 User’s Manual Choosing Your Application

Viewing Images in a Custom-designed Web Page

Often used as an attraction for enhancing a Web site with live images, this type of application represents the most basic form of network camera configuration. It is ideally suited for occasionally-visited sites on both large corporate networks and on SOHO

(Small-Office Home-Office) applications, where a small network is installed and maintained.

If you anticipate a large audience for your images, you should consider configuring your

product to upload images to an FTP server, as described in Sequentially Uploading Images

to a Remote FTP Server on page 32.

31

AXIS 2120

Browser

LAN/WAN

Intranet or Internet

Browser

Simply install the AXIS 2120 directly on your local Ethernet network and complete the

Installation Wizard to immediately view live video images in your own custom-designed

Web page. The Wizard not only helps you define the image format and personalized characteristics of your Web page Layout, but also allows you to determine how accessible the product is over your intranet or Internet network. You decide in just a few simple steps.

Installation and Configuration Overview

Configure your AXIS 2120 for viewing images over a network as follows:

1. Connect the AXIS 2120 to your local network. Refer to Installing Your Camera on a Network on page 12.

2. Open the product

Home Page in your browser and start the Installation Wizard; complete the Wizard to establish the standard Security, Date and Time, Image General Layout and TCP/IP Network settings - selecting network as your chosen method of connection in the

Modem or Network dialog. Refer to Configuring Your Camera on page 21.

3. The application setup is now complete. Having completed the Wizard, you should now verify the installation by checking that you have full access to both the images and the product Web pages in your browser.

Note:

Although custom HTML code is not supported by Axis, advanced users can optionally write their

own individual pages, as described in Appendix F - Custom Web Pages.

32

Choosing Your Application AXIS 2120 User’s Manual

Sequentially Uploading Images to a Remote FTP Server

Ideal for any busy Web site where a large audience is expected, this application uploads images to a designated FTP server on your network to provide image access to an unlimited amount of viewing clients over your intranet or the Internet

AXIS 2120

Browser

LAN/WAN

Intranet or Internet

Browser

Simply install the AXIS 2120 directly on your local Ethernet network and complete the

Installation and Application Wizards to develop an active application that will upload images to a designated FTP server - as a sequential stream that is unlimited, or at specified time periods. Then organize the times and the frequency at which your images are taken and uploaded to the target FTP server.

Installation and Configuration Overview

Configure the AXIS 2120 to actively upload images to an FTP server as follows:

1. Connect the AXIS 2120 to your local network. Refer to Installing Your Camera on a Network on page 12.

2. Open the product

Home Page in your browser and start the Installation Wizard. Complete the Wizard to establish the standard Security, Date and Time, Image General Layout and TCP/IP Network settings - selecting network as your chosen method of connection in the

Modem or Network dialog. Refer to Configuring Your Camera on page 21.

3. Continue the configuration of your product using the

Application Wizard to define the target FTP server and your preferred mode of operation - choosing Sequential mode to create your active application.

4. Having completed the Wizard, you should now verify the configuration by accessing the images stored on the FTP sever from your browser.

AXIS 2120 User’s Manual Choosing Your Application

Uploading Pre and/or Post Alarm Images to a Remote FTP server

The AXIS 2120 is an ideal solution for a wide variety of remote monitoring applications.

By creating windows for in-image motion detection, or by connecting an external alarm device to the I/O connector, you can quickly configure the product to upload single images, or send pre/post alarm image sequences to an FTP server when a time or alarm-based event occurs.

Using the available Wizards, you organize the times and frequency at which images are taken and uploaded to the target FTP server, and optionally arrange for e-mail alerts containing single images, or Web references to recorded image sequences.

Installation and Configuration Overview

Configure the AXIS 2120 to upload Pre and/or Post Alarm images as follows:

1. Connect the AXIS 2120 to your local network. Refer to Installing Your Camera on a Network on page 12.

2. Open the product Home Page in your browser and start the Installation Wizard. Complete the Wizard to establish the standard Security, Date and Time, Image General Layout and TCP/IP Network settings - selecting network as your chosen method of connection in the

Modem or Network dialog. Refer to Configuring Your Camera on page 21.

3. Continue the configuration of your product using the Application Wizard to define the target FTP server and define your preferred mode of operation - choosing Alarm Mode to upload single images, or pre/post alarm image sequences, when a defined alarm or time-based event occurs.

4. Having completed the Wizard, you should now verify the configuration by triggering the defined alarm event and then viewing the uploaded images in your browser.

33

Note:

For full details on how to create and use motion detection windows, see Motion Detection on page 26.

34

Choosing Your Application AXIS 2120 User’s Manual

Modem Applications

If a local network connection is not available at your chosen point of installation, you can alternatively connect your AXIS 2120 to a V.90-compatible modem and quickly configure any number of exciting applications using the Wizards; including:

• Viewing images in a fully custom-designed Web page over a Dial-up modem connection.

• Sequentially uploading images to an ISP (Internet Service Provider) over a dial-up modem connection and publishing images to the whole Internet community.

• Uploading single or pre/post alarm image sequences to your ISP over a dial-up modem connection, when an alarm or time-based event occurs; and optionally, sending e-mail alerts containing single images or Web links to pre/post alarm images stored by your ISP.

Important!

• Although the AXIS 2120 is compatible with most V.90-compliant modems, Axis does not undertake any responsibility for V.90 modems that fail to work with the product.

• When the AXIS 2120 is dialing out it will obviously not be possible to dial-in to it. If you configure an interval during which the camera will not be dialling out, this will allow you to dial-in and make any necessary changes etc.

Configuration

All modem applications must initially be configured from a browser on a local computer. If available you should always use an Ethernet network for this purpose, even if the actual application will be using a modem. If there is no network available, you can instead use the supplied Null Modem Cable to create a direct connection to the AXIS 2120 from the computer. This direct connection is only intended as an alternative for the initial configuration of the modem application when there is no network available. The Null

Modem Cable should not be used for any other purpose.

Note:

Once the Dial-up modem connection has been created and the AXIS 2120 is physically connected to the modem, you can then dial-up your AXIS 2120 in exactly the same way as you would to your ISP. The installer of the camera uses the Installation and Application Wizards to establish the basic parameters for your application, and advanced users can then use the Administration Tools to refine the application.

AXIS 2120 User’s Manual Choosing Your Application

Picture Frequency for Modem Applications

When used with a modem, the speed of your communications link will normally determine the image frequency in your browser. A standard image is normally transmitted in 2-5 seconds, although optimal image frequency is achieved by buffering the video stream into internal memory before uploading the recorded images to your ISP or Web server. This is the ideal solution for remote applications connected to external security devices and which require a good flow of images from alarm events.

Proprietary ISP Dial-up Protocols

If your ISP requires you to install special software before initiating a Dial-up connection, it is likely that your ISP is using proprietary protocols incompatible with the standard-based

AXIS 2120. In these circumstances, Axis recommends that you ask your ISP for an alternative dial-up service that allows for standard dial-up networking, or ask them to provide a standard Linux dial-up connection. Axis does not guarantee the compatibility of this product with any ISP requiring the use of proprietary or non-standard software as a pre-requisite for Dial-up connections.

35

36

Choosing Your Application AXIS 2120 User’s Manual

Remote Imaging in a Custom-designed Web Page

The AXIS 2120 can be configured as a standalone application that is remote from any network. Ideal for remote monitoring, home security, and process control applications, you can quickly configure the AXIS 2120 for direct connection to a serial modem. Use this application to view remote images from anywhere - from the comfort of your home, or the convenience of your office.

PSTN

Modem

Modem

AXIS 2120

Browser

Once the dial-up connection for your AXIS 2120 is established, the product plugs directly into a serial modem to provide immediate access to live video images in your own custom-designed Web page. You access the images and the product Web pages in exactly the same way as you would when connected to your ISP.

Installation and Configuration Overview

Configure the AXIS 2120 for viewing images over a dial-up modem connection as follows:

1. Connect the AXIS 2120 to the network if available. Otherwise, use the supplied Null Modem Cable. Connect a computer and

initiate a dial-up connection to the camera. For this and general information on the dial-up connection, refer to Installing

Your Camera to a Modem on page 15.

2. Create a dedicated dial-up Connection.

3. Refine the dial-up parameters.

4. Initiate the dial-up connection.

5. Referring to Configuring Your Camera on page 21, open the product Home Page in your browser and start the Installation

Wizard. Complete the Wizard to establish the standard Security, Date and Time, Image General Layout and Modem settings - selecting

modem as your chosen method of connection.

6. Disconnect the AXIS 2120 from the network or Null Modem Cable and connect it directly to the modem.

7. The application setup is complete. You should now verify the installation by remotely accessing the AXIS 2120 Web pages from your browser via the connected modem.

Note:

Except for when the AXIS 2120 is dialing-out, you can refine or amend the product configuration at any time using a remote Dial-up connection - or a local computer connected via the supplied

Null Modem Cable.

AXIS 2120 User’s Manual Choosing Your Application

Uploading Images to Your Internet Service Provider

Perfect for Web attractions, remote monitoring and process control applications; the AXIS

2120 can be quickly configured to dial-out from any remote location and transmit live images to an Internet Service Provider - where your images can then be accessible to several specific users, or the whole Internet community! You can select any of the supported Public ISPs supported in the Application Wizard, or specify a Public or Private

ISP of your own choosing.

AXIS 2120

Modem

37

Internet

Browser

ISP

Having established the Dial-up connection for your AXIS 2120 using the Installation

Wizard, continue with your configuration using the Application Wizard to develop an

active application, which uploads live images to a designated ISP over standard phone lines. You can arrange for image files to be transmitted as a sequential stream, or only at specified time periods; and you can set the times and frequency at which images are taken and uploaded to your ISP.

Installation and Configuration Overview

Configure the AXIS 2120 to upload images to an Internet Service Provider, as follows:

1. Connect the AXIS 2120 to the network if available. Otherwise, use the supplied Null Modem Cable. Connect a computer and

initiate a dial-up connection to the camera. For this and general information on the dial-up connection, refer to Installing

Your Camera to a Modem on page 15.

2. Create a dedicated dial-up connection.

3. Refine the dial-up parameters.

4. Initiate the dial-up connection.

5. Referring to Configuring Your Camera on page 21, open the product Home Page in your browser and start the Installation

Wizard. Complete the Wizard to establish the standard Security, Date and Time, Image General Layout and Modem settings - selecting

modem as your chosen method of connection.

6. Continue the configuration using the

Application Wizard to define your preferred ISP and mode of operation - choosing

Sequential mode to upload an image sequence that is unlimited or restricted between specified time periods but independent of any alarm event.

7. Disconnect the AXIS 2120 from the network or Null Modem Cable and connect it directly to the modem.

8. The application setup is complete. You should now verify the installation by remotely accessing the images that are now stored by your ISP.

38

Choosing Your Application AXIS 2120 User’s Manual

Uploading Pre/Post Alarm Images to Your Internet Service Provider

Perfect as a remote imaging tool, the AXIS 2120 not only transmits live video streams over a standard Dial-up connection, but also supports in-image motion detection and the connection of a wide variety of standard external alarm devices.

Using the Application Wizard, the AXIS 2120 is quickly configured for uploading single or pre/post alarm images to an ISP under alarm conditions. You define the times and the frequency at which images are taken and uploaded to the ISP, and optionally arrange for e-mail alerts containing single images, or Web references to image streams stored with your ISP.

Installation and Configuration Overview

Configure the AXIS 2120 to upload images to an Internet Service Provider in Alarm Mode, as follows:

1. Connect the AXIS 2120 to the network if available. Otherwise, use the supplied Null Modem Cable. Connect a computer and

initiate a dial-up connection to the AXIS 2120. For this and general information on the dial-up connection, refer to Installing

Your Camera to a Modem on page 15.

2. Create a dedicated dial-up connection.

3. Refine the dial-up parameters.

4. Initiate the dial-up connection.

5. Referring to Configuring Your Camera on page 21, open the product Home Page in your browser and start the Installation

Wizard. Complete the Wizard to establish the standard Security, Date and Time, Image General Layout and Modem settings - selecting

modem as your chosen method of connection.

6. Continue the configuration using the

Application Wizard to define your preferred ISP and mode of operation: choose Alarm Mode to upload single images, or upload pre/post alarm image sequences when in-image motion is detected or

when a defined alarm or time based event occurs. For information on how to create and use motion detection windows, see

Motion Detection on page 26.

7. Disconnect the AXIS 2120 from the network or Null Modem Cable and connect it directly to the modem.

8. The application setup is complete. You should now verify the configuration by triggering the defined alarm event and then viewing the resultant images uploaded to your ISP.

Note:

Except for when the AXIS 2120 is dialing-out, you can refine or amend the product configuration at any time using a remote dial-up connection or a local computer connected via the supplied

Null Modem Cable.

AXIS 2120 User’s Manual Adjusting the Camera Focus

39

Adjusting the Camera Focus

The AXIS 2120 has a varifocal DC Iris lens that automatically regulates the amount of light entering the camera, to provide a wide-angle zoom with a minimal amount of distortion.

Complete with a standard CS-mount, this supplied lens can also be replaced by any other lens conforming to the same standard.

Direct Focusing in Your Browser

Supporting rotational focus control, the AXIS 2120 can be targeted for different applications. With your video feed displayed on a local desktop, simply adjust the camera focus ring until you are satisfied with the focus.

However, for remote installations - where you cannot view your video images directly from your chosen point of installation - you can achieve a good level of camera focus by using the Focus Assistant, described later in this section.

Notes:

•The text information printed on the lens assembly will clearly define the focusing polarity (

F,

, and N) for the focus ring supplied with your unit. The camera focus is adjusted for either Far-focus

(F,

) or Near-focus (N) by rotating the focus ring in the appropriate direction.

•The lens rotates on a screw fitting and can be completely removed. If you need to remove the lens, take care not to let any dust enter the lens or the camera window as this can adversely affect the quality of your live images.

Important!

The lens assembly illustrated below is NOT typical for all lens types.

Lock Ring Focus Ring

Wide/Tele Zoom

Using the The Focus Assistant

Important!

As an alternative to the procedures described here, you can also enable and use the Focus Assistant directly from the Administration Tools. For more information on this, please refer to the on-line help.

Enabled using the Control Button (or from the Administration tools), the Focus Assistant works in conjunction with the Status Indicator to provide an onboard visual display for focusing your camera. With the Focus Assistant enabled, the Status Indicator displays

Green when the camera is focused - which means that you can conveniently focus the

AXIS 2120 without having to monitor the images in a desktop browser.

40

Adjusting the Camera Focus AXIS 2120 User’s Manual

Focusing Quality

The table below shows the full range of colors displayed by the Status Indicator when the

Focus Assistant is enabled; where each color represents a predefined level of focus:

Color

Red

Yellow

Green

Level of Focus (%)

0 - 60

60 - 80

80 - 100

Focus Quality

Poor

Reasonable

Good

Plane of Focus

The AXIS 2120 has rotational focus control that allows the focal length of the lens to be adjusted manually. Dependent upon the chosen physical location for your camera, it is likely that several planes of focus will exist throughout the full focusing depth of the unit.

Consequently, the Status Indicator is likely to display green - indicating a good level of focus - several times throughout the full travel of the lens assembly.

Focusing Procedure

Before you begin:

For the focusing algorithm to work efficiently, always ensure that there is minimal movement within the camera’s field of view when focusing your camera, as described below.

With reference to the accompanying illustrations, follow the instructions below to achieve a good basic level of focus under stable conditions:

Important!

Do not press the Control Button for at least10 seconds after powering up the unit as this will cause the

AXIS 2120 to return to the factory default settings.

1. Power up the AXIS 2120 and then wait at least 10 seconds.

2. Turn the lens to its extreme Far-focus (F,

) position.

AXIS 2120 User’s Manual Adjusting the Camera Focus

3. Enable the Focus Assistant: Using a suitably pointed object, press and continue to hold the Control Button - until the Status

Indicator flashes Yellow.

The Focus Assistant is now enabled with the

Status Indicator set to Focus Mode; the

AXIS 2120 now initiates a focusing algorithm to regularly calculate the quality of focus.

4. In order for the Focus Assistant to access the full focusing range for your application environment, now turn the lens to its extreme Near-focus (N) position.

5. Finally, turn the lens slowly towards the

Far-focus (F,

) position - until the Status

Indicator displays Green; that is, until a

Good level of focus is achieved.

Status Indicator

Control Button

Lens Assembly

Notes:

•A Good level of focus is normally achievable throughout several planes within the focusing range of the camera.

•The Status Indicator displays Green to indicate a Good level of focus at 80% of optimum focus.

•Since optimum focusing is dependent upon the camera’s field of view, it is important to scan the focusing plane from the closest to the furthest perspectives before attempting any fine-tuning.

6. Return to your browser and review the picture quality. If you consider the focal distance too distant - repeat steps 4 & 5 until you are satisfied with both the focal distance and quality.

7. To exit the Focus Assistant: press and hold the Control button - until the Status

Indicator flashes Yellow. The Status Indicator displays Green when the Focus

Assistant is closed.

41

42

Adjusting the Camera Focus AXIS 2120 User’s Manual

Replacing the Lens

Since the AXIS 2120 is designed with a CS-mount, the lens supplied with your product can be replaced with any standard C or CS lens typically used within the surveillance industry.

Note:

Although the lens supplied with your product can be directly replaced with any CS-type lens, a

C-type lens must be installed with an adaptor for it to work with your AXIS 2120. An adaptor effectively moves the lens 5mm farther from the camera.

Follow the instructions below to replace the supplied DC-Iris lens with any C or CS type lens:

1. Unscrew the AXIS 2120 lens.

2. C-lens only: Attach the new lens to a C-CS Adapter.

3. Screw the new lens onto the AXIS 2120. If applicable, adjust the iris according to the prevailing light conditions.

4. Referring to Focusing Procedure on page 40, adjust the camera focus.

5. Hit Refresh in your browser and monitor the results from the product Home Page.

Adjusting the DC-Iris Settings

If you choose to replace the lens supplied with your AXIS 2120 with something more specific to your end-user application, the DC-Iris settings must be adjusted from their standard factory default. In this case, you will need to modify the Exposure Control and other related settings for your camera from the Image-Advanced page.

Use the information presented in the following tables to choose the appropriate settings for your lens type.

Caution!

Exposing your camera to bright sunlight may cause permanent damage to the CCD if you:

• install and use a non-DC Iris lens with the product, or

• select anything other than DC-Iris in the Exposure Control settings of the Image - Advanced page.

Axis consequently advises extreme caution when changing the lens and/or when using the Image -

Advanced settings, as failure to do so may invalidate your product warranty.

AXIS 2120 User’s Manual Adjusting the Camera Focus

Exposure Control Overview

The table below provides a summary of the Exposure Control settings in the Image -

Advanced page. Select the parameters appropriate to your lens type and product application:

Lens Options

DC Iris

Description

The AXIS 2120 is supplied with a DC Iris lens as standard; consequently, the DC Iris setting is the standard factory default setting within the Image-Advanced page. It allows the user to manually specify the exposure, shutter speed, gain, and ALC levels.

Non DC Iris - Manual

Non DC Iris - Shutter

Non DC Iris - Auto

Choose this setting if you have fitted a non-DC Iris lens to your AXIS 2120, but wish to adjust the shutter speed and gain manually.

Choose this setting if you have fitted a non-DC Iris lens to your AXIS 2120, but wish to adjust the shutter speed,manually.

Choose this setting if you have fitted a non-DC Iris lens to your AXIS 2120 and would like the shutter speed and gain to be adjusted automatically.

43

Other Advanced Parameters

Lens Options

Shutter Speed

Description

Derived from the shutter speed on a normal camera, this parameter defines the exposure period for each image. Use a high shutter speed only if your image subject is expected to be moving quickly; otherwise, a slower speed will normally suffice.

Sharpness Defines a level of differentiation between light and dark areas in the image. Corresponding higher levels of sharpness provide for sharper images, but also cause the image compression to be more complex. Consequently, the file size of a sharp image can be significantly greater than for an image that is less sharp.

Gain

ALC Level

Adjust the gain to suit the average level of light at your point of installation. The AXIS 2120 should be set to a corresponding higher level of Gain if your camera is normally monitoring an area at night, or is sited in a dark room or cupboard.

This defines how acutely the lens reacts to a single light source within the image. For example, with the ALC level set to a lower level, the headlights from a car will generally cause the calculated average level of light to increase, and subsequently result in a compensated image that is usually much darker.

Adjusting the ALC to a higher level reduces the sensitivity of the lens to single light sources within the image.

44

Adjusting the Camera Focus AXIS 2120 User’s Manual

Adjusting the Back Focus

Your AXIS 2120 is supplied with the back focus roughly set to accommodate a reasonable level of focus throughout the complete focusing range. However, if you are using a lens other than that supplied with your product - or you are dissatisfied with the quality of focusing at a specific plane (or at several planes) within the focusing range, you may need to make some fine adjustments to the back focusing of the lens. This is performed by adjusting the focus and zoom rings of the camera lens, as described below:

Procedure

1. With the Focus Ring set to the Far-focus (F,

) position, aim the camera at a subject over 30 metres away.

2. Set the lens assembly to wide angle, and adjust the back focus by loosening the Lock

Ring and then turning the lens assembly. Continue to turn the lens assembly until you achieve optimum image clarity

3. Check that you obtain sharp pictures at various zoom grades and various distances.

Note:

If possible, it is better to perform this adjustment in low light conditions, or with a filter covering the front optic. This will ensure the iris is fully open to give the smallest depth of field, and therefore the best results.

AXIS 2120 User’s Manual The AXIS 2191 Audio Module

45

The AXIS 2191 Audio Module

The AXIS 2191 Audio Module is an add-on device that provides audio capability to Axis network cameras. The module connects quickly and easily to the serial port of the camera and is configured and controlled via the camera’s user interface. The AXIS 2191 is supplied separately.

An Axis network camera (

or

) with an AXIS 2191Audio Module connected provides live audio and video to browser clients (

❶ and

) on the network.

Features and Functions

• Easy to install and use

• Runs on Ethernet LANs and/or the Internet

• Built-in omni-directional microphone

• Compatible with most microphones and speakers (not included)

• External microphone via 3.5mm socket or Line-In via the terminal block

• Simple configuration and management via the network camera’s administration pages

• Can be used in Full-Duplex, Half-Duplex or Simplex mode (see page 49)

• Push-to-talk button in client user interface in Half-Duplex or Simplex - Talk mode

• Fully adjustable input and output levels

• Mute function

Legal Considerations

Video and audio surveillance may be prohibited by laws that vary from country to country. Please check the laws in your local region before using Axis network cameras or the AXIS 2191 Audio

Module for surveillance purposes.

46

The AXIS 2191 Audio Module

The Front Panel

Power Connector

AXIS 2120 User’s Manual

Serial Port Connector - Connect the serial cable from here to the serial port on the camera.

In

Power Indicator - Normally lit.

The Rear Panel

3.5mm socket for connection of external microphone.

Volume In

Level control for input. Use a screwdriver to adjust.

Int-Ext

Set to

Int for internal microphone or

Ext for external microphone or

Line-In.

Level In/Level Out

The colors used to indicate the input and output levels are:

• Green - Level OK

• Yellow - Risk for overload

• Red - Overload

Activity Indicator - Lights up when the camera has configured the audio module.

Mic

Built-in omni-directional microphone.

Volume Out

Level control for speaker volume.

Use a screwdriver to adjust.

Line Out

3.5mm socket for speakers with built-in amplifier, e.g.

PC speakers.

Terminal Block Connector

Used for:

• Line-In (e.g. CD, radio)

• Speaker-out (headphones or speakers without amplifier)

AXIS 2120 User’s Manual The AXIS 2191 Audio Module

Installing the Audio Module

Before installing the AXIS 2191 Audio Module, first install your network camera. Refer to the

installation section on page 12. If you intend running the audio module in full-duplex mode, check

that the sound card on your computer supports this.

If using an external microphone, connect it to the socket provided. To use an alternative input device, (e.g. CD-player or radio) connect it to

Line-In on the terminal block.

47

Set the selector switch to Ext to use an external microphone or device.

Otherwise, set to Int to use the internal microphone.

Connect a loudspeaker to the 3.5mm socket (amplified speakers only), or to

Out on the terminal block (speakers with no amplification). Other devices (including headphones) are connected to the terminal block.

Using the supplied cable, connect the audio module’s serial port to the network camera’s serial port.

Connect power to the audio module.

Check that the power indicators on both the audio module and the camera are lit. Note that the power LED will blink during power-up.

Using a screwdriver, adjust the Volume In control so that the Level In

LED occasionally shows yellow, but not red.

To verify the connection to the AXIS 2191, start Internet Explorer and enter the IP address of the network camera in the location/address field, e.g. 171.1.2.200, as shown here. Configure the audio module from the camera’s administration pages, as described in the following section.

48

The AXIS 2191 Audio Module AXIS 2120 User’s Manual

Configuring the Audio Module

The network camera’s administration pages provide all the tools required for successfully configuring the AXIS 2191. From the camera’s home page, click on the link to Administration

Tools. A new page containing the tools will open. To complete the configuration of your audio module, follow these instructions:

Admin tools

1.From the Admin tools, click External Devices. Select the

AXIS 2191 Audio Module as the device to use. Click Save.

Note: If you do not see External Devices, then your camera does not have the correct firmware installed and it must be

upgraded. Please see Updating the Firmware, on page 62.

2.Under External Devices, click Audio. This opens the configuration page for the audio module (see illustration below).

3.Select the audio mode. This can be:

• Full-Duplex (Talk and Listen Simultaneously)

• Half-Duplex (Talk and Listen)

• Simplex - Talk

• Simplex - Listen

This selection will depend on your application. See page 49 for more information.

4. Enter the number of clients that will be able to access the application at any one time. Use this setting to limit access if you only have limited bandwidth available.

5. If you are using Half-Duplex mode, the Send option can be used to send audio from the client currently transmitting to all the other clients, and not just to the server end. Set to

Yes to enable the function.

6. When using Half-Duplex, the Push-To-Talk button will be visible. Select the mode to use for this button. Selecting Toggle means that when the button is pushed it will remain so until pushed again. Instant means that the button will remain active (pushed) until released.

7. Adjust the Volume Out control until a satisfactory speaker level is heard. The Level

Out LED can be used to check that there is audio being received. Note that both the control and the LED are on the audio module itself.

The configuration page for the AXIS 2191.

AXIS 2120 User’s Manual The AXIS 2191 Audio Module

Using the Audio Module with Your Camera

Your audio module is now configured and ready for use with your network camera. Enter your camera’s IP-address in Internet Explorer, or click Home on the camera’s admin page. You should then see the control panel for the AXIS 2191 below the camera image. If no audio controls are visible, check that you have made the correct setting under External Devices.

Push-To-Talk

Used in Half-Duplex or

Simplex - Talk mode.

The button’s own mode is set in the camera’s admin pages.

NB. Exactly which controls will be visible below the image depends on the audio mode you are using.

For example, the Push-to-Talk button will not be visible in

Full-Duplex mode. Similarly, when using Simplex - Listen mode, only the Speaker controls will be shown. The audio mode is set in the camera’s admin tools.

Available Bandwidth

Select the bandwidth available for your connection.

Show/Hide Settings

Shows or hides the slider controls and level indicators

Level Adjust IN/OUT

Drag sliders to adjust level.

Mute Checkboxes

Check to mute speaker or microphone.

Using the Different Audio Modes

Full-Duplex

Full-Duplex mode means that you can transmit and receive audio (talk and listen) at the same time, without having to use any of the controls. This is just like having a telephone conversation. The only controls you may wish to use are the mute checkboxes to turn off the sound, and the level sliders, to adjust the input/output levels. This mode requires a full-duplex sound card on your computer. If your available bandwidth is 0.2Mbit/s or less, it is recommended that you use Half-Duplex mode instead.

Half-Duplex

Half-Duplex mode also sends and receives audio in both directions, but only in one direction at a time. This means you must actively transmit with the help of the

Push-to-Talk button. To speak, press the button (check that the microphone is not muted).

When finished speaking, release the button. You will now be receiving audio from the other end of the connection. Note that the Push-to-Talk button can be configured for use in two different ways - Toggle or Instant. This is set in the camera’s admin tools.

Half-Duplex mode is best if you only have limited bandwidth available.

49

50

The AXIS 2191 Audio Module AXIS 2120 User’s Manual

Simplex - Talk

Simplex - Talk mode means that only the web-client end of the connection can transmit audio (that is, to the AXIS 2191). This could be used, for example, to provide spoken instructions to a person seen in the network camera. This mode also requires you to use the

Push-to-Talk button.

Simplex - Listen

Simplex - Listen mode can only receive audio from the AXIS 2191 to the web-client. This can be used in remote monitoring, web attractions etc., to provide live audio, as well as video, of a monitored situation.

AXIS 2120 User’s Manual The AXIS 2191 Audio Module

Troubleshooting the Audio Module

Symptoms

No audio controls below camera image.

Possible causes

The AXIS 2191 is not selected as the external device.

Wrong camera firmware.

No sound from the AXIS

2191 or from a PC trying to access a web page containing audio content.

No audio signal from PC to the AXIS 2191 when passing a proxy server.

No full-duplex function.

Poor performance.

Incorrect settings or faulty connections.

The Post Content Length set in the proxy server is too low.

Incorrect configuration.

Sound card does not support full-duplex.

Too many users/clients connected.

Low bandwidth.

Remedial actions

In the camera’s administration tools, click on

External Devices and select the AXIS 2191 Audio Module.

Check the firmware in the camera by checking if External Devices appears in the camera’s Administration Tools. If not, the camera does not have the correct firmware and it must be upgraded.

Check that:

• soundcard, speakers and microphone are connected

• the Mute button is not pressed

• the Int/Ext switch for the input is in the correct position

• the input and output levels are correct

• all cabling is connected and all power switches are ON

Set the value of the Post Content Length in your proxy server to 1MB or more. You may need to contact your system administrator to do this.

Check the setting in the camera’s administration tools.

For information on how to check if your sound card supports full-duplex, please visit www.axis.com and see the support section for

Axis camera products.

Try limiting the number of clients allowed to connect.

Whining or screeching sound from speakers (feedback).

Poor positioning of speakers and/or microphone.

Poor sound on headphones.

Incorrect connection.

Faulty power supply.

Reduce the available bandwidth by changing to a lower setting in the

Available Bandwidth selector. Setting a lower bandwidth will reduce any break-up in the sound, but will also increase the transmission delay.

If running in Full-Duplex mode, try switching to Half-Duplex mode.

Relocate the speakers or microphone so that they do not point towards each other, and/or lower the volume.

Headphones can only be used by connecting them to Speaker-Out on the terminal connector.

Verify that you are using an AXIS PS-D power supply.

The Power indicator LED is not constantly lit.

The AXIS 2191 works locally, but not externally.

Firewall protection.

Default routers required.

Check the Internet firewall with your system administrator.

Check if you need to configure the default router settings.

Note:

If you still have a problem after reading this information, please contact your reseller, or visit www.axis.com and check the support section for Axis camera products.

51

52

The AXIS 2191 Audio Module AXIS 2120 User’s Manual

Technical Specifications for the AXIS 2191

Operating temperature: 40-105 o

(5-40 o

C).

F • Line Out: Unbalanced, 0.05-1.0Vpp

Humidity - 8-80% relative humidity.

EMC - : EN55024, EN55022, Class B and

EN61000-3-3.

EMC - FCC Class A of FCC Rules and Regulations part 15, subpart B.

Line Input: Balanced 0.05-1Vpp. Connect source ground to pin 2 and source signal to pin 1 if the source is unbalanced.

Speaker Output: Balanced, 0.5W. Impedance 8-32 Ohms. Connect directly to speaker without capacitors.

• EMC -

Alternative Power: 12-15VAC, min 10VA, or 15-20VDC, min 7W.

Full-duplex audio: Audio data encoded in

ADPCM format at 32kbps, 8 kHz sampling

(G.721). Data is sent using HTTP.

9-pin D-SUB serial connector: RS-232.

Metrics: Height: 1.1” (27mm),

Width: 4.4” (112mm), Length: 4.3” (110mm),

Weight: 0.7lb (0.32kg).

Power Input: Axis PS-D power supply.

Microphone Input: 1-50mVpp. PC type.

Maximum number of users: 10 (on local area network).

Connection Diagram

AXIS 2120 User’s Manual The AXIS 2191 Audio Module

The Audio Module to Camera Serial Cable

The serial cable supplied with your AXIS 2191 is wired as shown in the table below:

Audio Pin

Pinouts for the RS-232 Port

Pin Camera Signal

IN

IN

OUT

OUT

GND

IN

OUT

IN

Unused

5

6

7

8

9

1

2

3

4

5

6

7

8

9

1

2

3

4

IN

IN

OUT

OUT

GND

IN

OUT

IN

IN

CD

RXD

TXD

DTR

GND

DSR

RTS

CTS

RI

53

54

Troubleshooting AXIS 2120 User’s Manual

Appendix A - Troubleshooting

This appendix provides useful information to help you to resolve any difficulty you might have with your AXIS 2120. Symptoms, possible causes and remedial actions are provided in a quick reference table.

Frequently Asked Questions

Q: Which modem should I select in the list on the Modem Settings page if mine is not listed?

A: Generic.

Q: Do I have to use one of the listed ISPs on the ISP Settings page?

A: No. You can make whatever settings you like for your own ISP. You can use the name

"Generic" for your own settings.

Q: When should I use the Null Modem Cable?

A: This cable is only intended as an alternative for configuring your camera when there is no network available.

Q: Can I set up my camera to run as a PC-cam on my computer?

A: No. The AXIS 2120 is a network camera for use only on Ethernet networks or with a modem.

Q: Do I have to use the Wizards whenever I want to make changes?

A: No. Everything that is configured in the Wizards can also be configured individually from the links on the left hand side of the Administration Tools page.

Q: What are the ftp-path, the ftp-host name and ftp-user name?

A: If you are uploading your images to an ftp-server, the ftp-path is the location of the directory on the remote ftp-server where you will be saving your images, the ftp-host is the name or IP-address of the ftp-server and the ftp-user name is the identity you use for logging in to the ftp-server.

AXIS 2120 User’s Manual Troubleshooting

55

PINGing Your IP Address

By sending a packet to the specified address and waiting for a reply, the PING utility can determine whether a specific IP address is accessible. It also provides a particularly useful method for confirming addressing conflicts with your AXIS 2120 on the network.

Follow the instructions below in association with Symptoms, Possible Causes and Remedial

Actions, on page 56, and run the PING utility to troubleshoot TCP/IP problems on your

network:

1. Start a Command window.

2. Type

ping x.x.x.x

, where

x.x.x.x

is the IP address of the AXIS 2120.

3. If you recieve the reply destination host unreachable,

then the AXIS 2120 is not accessible on your subnet. You must obtain a new IP address and reinstall the unit.

If this does not solve the problem, disconnect the AXIS 2120 from the network and run the

PING command again. See the table below for an interpretation of the results.

PING Reply

Reply from <IP address>: bytes = 32; time = 10 ms.....

Request timed out

Interpretation and recommendation

The IP address is already used and cannot be used again. You must obtain a new IP address.

This IP address is not used and is available for use with your AXIS 2120. If you set the IP address previously, the installation might not have been performed correctly. In this case, reinstall the unit. Also check all cabling.

56

Troubleshooting AXIS 2120 User’s Manual

Symptoms, Possible Causes and Remedial Actions

Symptoms

The AXIS 2120 cannot be accessed from a browser.

Possible causes

The IP address is already used by another device.

Remedial actions

Run the PING utility (as described in PINGing Your IP Address, on page 55) and follow the appropriate recommendations.

Note: The assigned IP number can be assumed valid if the PING utility returns “request timed out” - in which case you should set the IP address again, power on the AXIS 2120 and then try accessing the unit again.

The IP address is located on a different subnet.

Run the PING utility (as described inPINGing Your IP

Address, on page 55). If the utility returns “no response” or

similar, the diagnosis is probably correct - you should then proceed as follows:

In Windows, check that the IP address for your AXIS 2120 is on the same subnet as your workstation. Exactly how this is done varies from one version of Windows to another. See Windows’ help for more information.

If your AXIS 2120 is on a different subnet than your workstation you will not be able to set the IP address from this workstation.

Contact your network administrator.

In Windows 95, the ARP table was empty when you tried to set the IP address.

In Windows 95, the ARP command cannot be used if you have an empty ARP table.

If the table is empty, re-install the product ensuring that the IP address for your own PC is also used. Type arp -a to view the ARP table.

Note: The AXIS IP Installer provides a good alternative to ARP.

Possible problem with your proxy server.

Try disabling the proxy default in your browser.

The Power indicator is not constantly lit

Other networking problems.

Try replacing your network cable.

Test the network interface of the product by connecting a local computer to the unit, using a standard Crossover (hub-to-hub)

Cable.

Faulty power supply.

If the above actions do not resolve the problem, the AXIS 2120 may be faulty. In this case, try to localize the problem by connecting the

AXIS 2120 to the serial port of a local computer, using the supplied

Null Modem Cable; and report your findings to your local distributor.

Verify that you are using an AXIS PS-D power supply.

AXIS 2120 User’s Manual Troubleshooting

57

Symptoms

The Network indicator displays red.

Possible causes

Faulty cabling.

Remedial actions

1. To verify that the cable is functional, connect the cable to a known functioning device on the network and PING it from your workstation.

2. If the cabling is OK and your network is reachable, you should receive a reply similar to this:

Reply from <IP address>: bytes = 32; time

= 10 ms.....

Contact your Axis dealer.

The Active and Network indicators are flashing every 0.5 seconds

Hardware failure.

Your AXIS 2120 works locally, but not externally.

Slow image updating

No image using Refresh and/or slow updating of images.

Firewall protection

Default routers required

Check the Internet firewall with your system manager.

Check if you need to configure the default router settings.

The Internet site is too heavily loaded

Configure the AXIS 2120 to upload your video images to an FTP server or an ISP.

Requests for images of varying size and resolution place a greater demand on the available file space within the AXIS 2120.

Ensure that all the clients accessing the images are using the same image resolution and compression. For large numbers of clients, configure the AXIS 2120 to upload your images to an FTP server or an ISP.

Cannot access the connected modem.

Modem not properly connected.

Check the modem power supply and modem cable connections, and ensure that the modem is configured appropriately.

Incorrect initstring.

Send command AT&F1 to return your modem to factory default, and then try accessing the modem again. If this does not resolve the problem, it is likely that your modem uses an initialization string that is different from the standard ATZ command used by the

AXIS 2120. In this case, refer to the user information supplied with your modem to find the unique initstring command for your unit.

A series of broad vertical white lines appear across the image.

The CCD sensor becomes overloaded when the light is too bright. This can happen e.g. with sunlight reflexes.

Direct exposure to extreme sunlight or halogen light may cause serious damage to the CCD sensor. Reposition your AXIS 2120 in a more shaded location immediately.

Note: damage caused to the AXIS 2120 through over exposure to direct sunlight or halogen light is not covered by the product warranty.

58

Troubleshooting AXIS 2120 User’s Manual

Symptoms

Bad focus

Noisy images.

Bad quality images.

Possible causes

Focus has not been correctly adjusted.

Remedial actions

Referring to the on-line help, adjust the White Balance setting and then try resetting the camera focus again using the Focus Assis-

tant, as described in Adjusting the Camera Focus on page 39.

No adapter fitted with your

C-type lens.

If you have previously replaced the supplied CS-type lens, you may have inadvertently installed a C-type lens - without the required

adapter. See also page 42.

Video images may be noisy if you are using the AXIS 2120 in a very low light environment.

To solve this problem, you need more light. The performance of the camera is best in 100 - 3000 lux.

You may wish to consider replacing the basic lens with a more sensitive lens (Lower F-number), if the lighting in the installation area cannot be improved.

The Display Properties are incorrectly configured for your desktop.

Open the Display Properties in your desktop and configure your display to show at least 65000 colors, i.e. at least 16-bit.

Note: Using only 16 or 256 colors on your computer will produce dithering artifacts in the image.

The camera is not focused correctly.

Referring to the on-line help, adjust the White Balance setting and then try resetting the camera focus again using the Focus Assis-

tant, as described in Adjusting the Camera Focus on page 39.

No images available in your browser application.

ActiveX disabled.

If you are using Microsoft Internet Explorer, ensure that ActiveX has not been disabled. Alternatively, use the Java Applet for viewing images.

Note:

If you still have a problem after reading this information, please contact your reseller or check the FAQ on the AXIS 2120 product pages at the Axis Website at www.axis.com.

AXIS 2120 User’s Manual Other IP Setup Methods

59

Appendix B - Other IP Setup Methods

In addition to the ARP command (described earlier in the Installation section of this manual), you can alternatively set the IP address for your AXIS 2120 using any of the following methods - as appropriate for your operating system:

Method

AXIS IP Installer

Operating Systems

Windows 95/98/ME and

NT/2000

UNIX

Refer to...

Using the AXIS IP Installer, on page 60.

BOOTP

Requiring a BOOTP daemon on your system, this method operates over the entire network. A request to an active daemon initiates a search of the boot table to find an entry matching the unit’s

Ethernet address. The daemon replys with the IP address for the device, if a match is found.

DHCP

This method should only be used if you know which

IP address the DHCP server will give the camera, or if your version of DHCP can update a DNS server, which then allows you to access the camera using a name.

Most

Notes:

•Do not use the default or IP address featured in these examples when installing your AXIS 2120.

If in doubt, consult your network administrator to obtain an unused IP address.

•Make sure the AXIS 2120 is powered up and attached to the network.

•Server Privileges: Although no special privileges are required for Windows 95/98, you do need

Administrator privileges for Windows NT/2000, and Root privileges on UNIX systems.

Ethernet Address: The AXIS 2120 is pre-configured with a unique Ethernet Address based upon the serial number printed on the underside label of the unit; where the serial number typically follows the format

00-40-8c-xx-yy-zz. You must know the Ethernet address to complete the installation.

60

Other IP Setup Methods AXIS 2120 User’s Manual

Using the AXIS IP Installer

AXIS IP Installer is a Windows program that is ideal for setting the IP addresses for multiple Axis networking products on your network. Also allowing you to access the home

Web page of any Axis ThinServer device connected to your network, this freely distributed software is available for download from www.axis.com.

Installing the AXIS IP Installer:

1. Download the latest AXIS IP Installer software onto your desktop and run the

Setup_IPInstaller.exe program to start the installation.

2. The AXIS IP Installer - Setup dialog is displayed on the screen.

3. Follow the instructions as they appear on the screen.

4. Click Finish to complete the installation.

Setting the IP Address with the AXIS IP Installer:

1. Run the AXIS IP Installer from the Start menu. The following window will appear:

2. Restart your AXIS 2120.

3. Select the serial number of your AXIS 2120 in the list. The serial number is identical to the unit’s Ethernet address.

4. Enter the IP address. Click Set IP address. The IP address will now be set.

5. To access the home page of the AXIS 2120, click Home page of selected Axis-server...

You can now configure the AXIS 2120 according to your requirements.

6. Click OK to exit the program.

For more help during the installation of the IP address, click Help or press the F1 key.

AXIS 2120 User’s Manual Other IP Setup Methods

Notes for Macintosh Users

The AXIS 2120 supports TCP/IP over Ethernet, or PPP Modem dial-up. You must use

TCP/IP on your Macintosh network, as there is no support for AppleTalk.

When using the AXIS 2120 on a Macintosh, please observe the following points:

• The camera has a default IP address of 192.36.253.80.

• Assign a temporary IP address in the same subnet (e.g. 192.36.253.81) to a Mac workstation and then connect to the camera.

• The desired IP address for the camera should be set using the Installation Wizard.

• The correct IP address for the Macintosh workstation should also be reset.

• Changing the IP address for a Macintosh is simple and there is no need to reboot.

Currently there are limitations in the ActiveX Support in Internet Explorer running on the

Macintosh. This results in problems when viewing live moving images. The recommended solution for viewing Axis cameras on the Macintosh is to use Netscape.

61

62

Updating the Firmware AXIS 2120 User’s Manual

Appendix C - Updating the Firmware

The AXIS 2120 camera firmware is stored in Flash memory. This memory is provided by a silicon chip that, just like any other ROM device, retains data content even after power is removed. Flash memory is unique because it allows its data to be erased and re-written.

This means that you can install firmware updates for your AXIS 2120 as soon as they become available - without having to replace any parts. New firmware can be simply loaded into the AXIS 2120 over the network.

Obtaining Updated Firmware

The latest version of the AXIS 2120 camera firmware is available free of charge from the

Axis website at www.axis.com or from your local distributor.

Upgrading the Firmware

The AXIS 2120 firmware is upgraded over the network using FTP. See the detailed instructions supplied with each new release.

Important!

• Always read the upgrade instructions available with each new release, prior to upgrading your firmware.

• Downloading normally takes between 30 seconds and 10 minutes, although it can take longer. After starting the download, you should always wait at least 20 minutes before power-cycling the AXIS

2120 - even if you suspect the download procedure has failed.

• In controlled environments, flash memory upgrades provide a very safe method for updating firmware. However, flash products can become damaged if the upgrade operation is not performed correctly. Your dealer reserves the right to charge for any repair attributable to faulty upgrading by the user.

AXIS 2120 User’s Manual The Unit Connectors

63

Appendix D - The Unit Connectors

This section provides a detailed overview of the two supported product connectors; namely the Serial Connector and IO Connector. It also includes a schematic diagram describing how the AXIS 2120 is connected for a typical application:

The Auto Iris Connector

The AXIS 2120 is supplied with a varifocal DC Iris lens that automatically regulates the amount of light entering the camera, and provides a distortion free wide-angle zoom.

The power and control signalling required for automatically adjusting the lens is supplied by the Auto Iris Connector that attaches to the lens via a connecting cable. The connector is located at the base of the camera, as illustrated below:

DC-Iris cable. Connected to the lens upon delivery, this cable supplies the power and electronic signalling to the lens from the DC Iris connector.

Below: DC Iris connector

- with the cable removed.

The AXIS 2120 is delivered with the Auto Iris cable already attached to the connector, and with the Auto Iris functionality enabled by default. Should you experience any problem with overexposure or white balance adjustment in your camera, check that the cable is firmly attached to the Auto Iris connector. Otherwise, the Auto Iris function requires no further intervention from the user. If you are unable to immediately resolve any apparent

fault, refer to Appendix A - Troubleshooting.

The Serial Connector

The serial connector can be used for several purposes. In the absence of a local network connection, the serial connector provides a physical interface for connecting a modem or computer to the AXIS 2120. When a local network connection is unavailable at the point of installation, connect your PC to this connector using the supplied Null Modem Cable to initially configure your product. If you intend to use the AXIS 2191 Audio Module with your network camera, then this is the connector used for connecting it.

64

The Unit Connectors AXIS 2120 User’s Manual

The Physical Connector

A single 9-pin D-sub connector provides the physical connection for the RS- 232 serial interface of the AXIS 2120. This interface is for use with an external modem and is suitable for speeds of up to 115kbps.

A diagram of the RS-232 connector complete with pinout information is shown below.

6

7

4

5

8

9

2

3

Pin

1

Function

CD (Carrier Detect)

RXD (Receive Data)

TXD (Transmit Data)

DTR (Data Terminal Ready)

GND (Ground)

DSR (Data Signal Ready)

RTS (Return To Send)

CTS (Clear To Send)

RI (Ring Indicator)

A view of the RS-232 connector as seen from the rear of the AXIS 2120

1

6

2

7

3

8

4

9

5

For pinout information concerning the

AXIS 2191

Audio Module, see

page 53

.

The IO Connector

A 4-pole connector is provided for auxiliary IO connections to the AXIS 2120.

Physical Connector

The IO connector provides the interface to a single digital output and a single digital input.

A diagram for the connector, complete with a pinout table, is provided below:

Pin

1

2

3

4

Function

Common Ground

Positive Connection for DC Power Input or Output:

Electrically in parallel with the derived DC power for the unit, this pin may be used as a power input or output. As a power input it can be used for remote applications to supply the AXIS

2120 via an external direct current source; for example, a 9-15V DC battery supply. Used as a power output, it can drive the photo coupled input or other equipment; such as an infrared sensor. The output voltage level is dependent upon the input voltage to the unit. A maximum current of 50mA can be sourced from the DC output.

Digital Input (photo-coupled anode):

Voltages 5-24V DC will activate the input. It is possible to use pin 2 to source the input.

Digital Transistor Output:

With a maximum load of 100mA and maximum voltage of 24V DC, this output has an open-collector NPN transistor with the emitter connected to pin 1. If it is to be used with an external relay, a diode must be connected in parallel with the load for protection against any

voltage transients - as detailed in the Schematic Diagram, on page 66. Important!

Connecting AC to the transistor output will damage the unit.

1

2

3

4

AXIS 2120 User’s Manual The Unit Connectors

Digital Input

Used for connecting external alarm devices and triggering images for specific alarm-based events, the digital input is typically connected to a motion detector (or any other external security device) for taking images on each occasion that the detector is activated.

Digital Output

The supported transistor output can drive a maximum load of 24V DC at 100mA directly, and by connecting additional relay circuitry, can drive even heavier loads.From the

Administration Tools you use ON/OFF buttons in the Layout settings to drive the output high or low.

65

66

The Unit Connectors

Schematic Diagram

Internal

3.3V

!

Switch

Mode

Power

Supply

AXIS 2120

!

!

!

!

!

!

!

AXIS 2120 User’s Manual

o

!

PS-D

9 VA o

!

!

1 o

3

2 o o

!

!

!

+

-

Infrared Sensor o o

!

o o

Appliance o x

4 o

!

o o

~

Mains Power

GND PIN 5

!

!

!

GND.

o

!

COM 1

Schematic diagram of the I/O and RS232 connector - showing a possible application

Caution!

Pins 1 and 2 are connected to the derived DC power for the unit, and can be used as an external power feed for external equipment, such as an infrared sensor. When connecting other equipment using this connector, the maximum current of 50mA must be strictly observed. Failure to do so may cause a loss of power to the unit and may even damage your camera.

AXIS 2120 User’s Manual High-Speed Services

67

Appendix E - High-Speed Services

You will experience the full performance of the AXIS 2120 if you have access to high-speed Internet services such as, xDSL or a cable-modem connection. However, as most high-speed Internet services only provide you with one external IP address, there are several practical issues that should be considered when developing your application.

Available IP Addresses

Ideally, your ISP (Internet Service Provider) will provide you with several external static IP addresses - in which case you can assign any one of these to your AXIS 2120 to make it fully accessible over the internet. However, if your service provider supplies you with only one IP number - which is often the case - this IP number is normally assigned to your PC - leaving no connection available for your AXIS 2120. If your ISP is unable to provide you with an additional IP number, there are a number of other options that you may like to consider; including:

NAT Box

Short for Network Address Translation, NAT is an Internet standard that allows a local-area network (LAN) to use one set of IP addresses for internal traffic and a second set of addresses for external traffic. A NAT box located where your LAN meets the Internet will handle all of the necessary IP address translations and provides:

• Internal IP addresses that are unique to your network - with no possibility of conflict with IP addresses used by other companies and organizations.

• The possibility of combining multiple ISDN connections into a single Internet connection.

• An effective firewall for hiding internal IP addresses

NAT Feature in Windows 2000

Utilize the NAT feature in Windows 2000 to allow multiple Ethernet cards in your PC, and you can then use one port for the Internet and the other for your internal network. With this solution, you can let your AXIS 2120 upload image streams to an external Web server that is maintained and located with your ISP.

Note:

For further details on Network Address Translation, see also RFC 1631.

68

High-Speed Services AXIS 2120 User’s Guide

Routers and Firewalls

Another ideal solution is to use one of several small routers/firewalls currently available on the market. These provide the necessary NAT functionality and allow complete independence for your PC, which can be switched off or rebooted without affecting the image transmission from your AXIS 2120.

WinGate Server Software:

Running on a single Windows computer, this software allows multiple users simultaneous access to the Internet through a single modem; ISDN; or high-speed line, such as xDSL or cable-modem connection; and effectively shares a single Internet connection with almost any type of client computer running TCP/IP.

For more advanced users, the WinGate 3.0 Standard and Pro versions also allow the administrator to change the IP bindings so that external requests may be routed specifically to your AXIS 2120 - running behind the WinGate software.

AXIS 2120 User’s Manual Custom Web Pages

69

Appendix F - Custom Web Pages

The AXIS 2120 contains a re-writeable flash memory file system that allows some directories and files to be changed by the root user, using FTP (File Transfer Protocol). This strictly non-supported product functionality, makes it possible for advanced users and application developers to add their own Web pages, scripts, and other files to the Axis product.

Caution!

Essentially a hidden feature within the AXIS 2120, modification of the flash file system is not supported by Axis Communications. In practice this means that Axis will not answer questions regarding Web page or script development.

In attempting to make any modification to the product, you may inadvertently create a problem that will require you to return the AXIS 2120 to its factory default settings. You may even cause permanent damage to the unit that renders it unusable. Consequently, Axis strongly recommends that inexperienced users DO NOT undertake any modifications described in this section.

Axis does not provide any support in association with this functionality nor take any responsibility for problems arising from it, but merely wish to inform potential application developers of the possibilities afforded by the Linux-based file structure of the AXIS 2120.

Customizing Procedures

Notes:

•The existing Administration pages are stored in a compressed read-only area of the file system.

If you intend to try changing these, you must strictly adhere to the instructions provided here and ensure that you DO NOT inadvertently change any files other than those featured in this section. Failure to comply with this notice may render your product unusable.

•All files stored in the /etc/httpd/html directory are available through the product Web server in the virtual directory /local/. The URL to resident pages in the /etc/httpd/html directory is http://IP/local/<filename>.htm

70

Custom Web Pages AXIS 2120 User’s Manual

Editing and Storing Your Webpages

Note:

Several demonstration and tutorial pages describe in some detail how to perform, execute, and implement various HTML development functions for your product.

Follow the instructions below to create and save customized pages to the AXIS 2120:

1. Using your preferred editor, create your html file and store it on your local PC hard drive.

2. Now use ftp to upload the file to the AXIS 2120. Enter the following on the command line: ftp <camera ip address >

Example:

ftp 172.21.1.200

3. Log on as root with the root password

pass

.

4. Change to the correct directory within the AXIS 2120 by entering the following command: cd /etc/httpd/html

5. For binary storage of the files (not absolutely necessary, although good practice), type

bin

6. Upload your html files by entering: put <filename.html>

7. Start your browser and view the Web pages you have now uploaded, by entering the following URL in the location/Address field: http://<camera ip address>/local/<filename.html>

Example:

http://172.21.1.200/local/index.html

The images are now updated in your browser.

Note:

You can change the html files as and when you like, but remember that the available flash memory is limited.

8. Enter

bye

in the command window to exit the ftp program.

AXIS 2120 User’s Manual Custom Web Pages

71

Creating a New Home Page

Having created and stored your new custom Web pages in product memory, you then proceed to assign one of these pages as your default Home page in the AXIS 2120, as described below:

Caution!

Adding a new Web page to your AXIS 2120 is not something that should be undertaken lightly. Remember: Axis does not support the personalization of product Web pages and strongly recommends that inexperienced users DO NOT perform such modifications.

1. Start a new ftp session to the AXIS 2120, by entering: ftp <camera ip address >

2. type

bin

3. Navigate your way to the appropriate directory, entering: cd /etc/httpd/conf/

4. Fetch the boa.conf file, by typing: get boa.conf

5. Add an alias to your own "homemade" index.html file stored in the /etc/httpd/html/ directory. This redirects access to your personalized Home page. For example:

Alias /usr/html/index.html /etc/httpd/html/index.html

Note:

As an alternative to the above, you might like to edit the DocumentRoot so that it points directly to the local directory. However, after doing this you will then be unable to access the original

Home pages - so be warned!

6. After making these changes, you must now type in the complete URL to access the normal index page: http://IP#/view/index.shtml

72

Technical Specifications AXIS 2120 User’s Manual

Appendix G - Technical Specifications

System Requirements -

The AXIS 2120 uses the standard Internet TCP/IP suite of protocols and can be used with most operating systems: Windows 95, 98, NT and 2000, Linux, UNIX,

Mac and others. The only software required is Microsoft Internet Explorer 4.x, or higher

(used with Axis’ ActiveX component AXIS Camera Control), or Netscape 4.x.

Installation -

Physical network connection using RJ-45 twisted pair cable. Remote connection using any standard serial modem, or local computer connected using the a Null

Modem cable.

Management -

Remote configuration and status using Web-based Administration Tools.

Image Features -

Time/date stamp, text overlay, variable size, color CGI control, and in-picture motion detection.

Image Resolution -

CIF = 352 x 288, QCIF = 176 x144, 4CIF = 704 x 576

Networking -

10baseT Ethernet or 100baseTX Fast Ethernet, TCP/IP, HTTP, FTP, SMTP,

NTP, ARP and BOOTP.

I/O Connector -

Providing a single optical-isolated alarm input, and a single digital output

(max 24V, 0.1A) that features a programmable digital input/output for remote image storage via File Transfer Protocol (FTP) or E-mail (SMTP), pre/post alarm image storage.

Pre/Post Alarm Buffer -

Up to 8 MByte memory available for pre/post alarm image storage.

Modem Connector -

Single 9-pin D-SUB RS232 connector, max 115 kbps, half-duplex.

Security -

Multi-user password protection.

Operating Conditions: -

Temp: 41to122 o

F (+5 to +50 o

C), Humidity: 8 - 80% RHG.

Approvals -

EMC: FCC Class A, :EN55024/1998, Emission: C-Tick (Australia), VCCI

(Japan),

Safety: EN 60950, UL, CSA.

Metrics: -

Height: 2.2” (5.7 cm), Width: 3.4” (8.6 cm), Length: 5.4” + lens 1.8” = 7.2”

(13.8 cm + 4.5 cm = 18.3 cm), Weight: 0.55 lb. (0.25 kg) - excluding power supply.

Hardware -

ARTPEC-1 compression chip; ETRAX-100, including, 32 bit RISC, 100 MIPS

CPU,

16 Mbyte DRAM, 4 Mbytes FLASH PROM.

AXIS 2120 User’s Manual Technical Specifications

Camera Lens -

Varifocal DC Iris lens with CS Mount, manual zoom, variable focus, and exposure control. Variable shutter speeds between 1/50 - 1/10000 (PAL) and 1/60 -

1/10000 (NTSC).

Power -

External power supply 12V AC, 9.6 VA (PS-D, included), 9-15V AC, min 10VA, or

9-15V DC, min 8W.

Complimentary Software -

AXIS IP Installer for quick installation of multiple units. AXIS

Camera Control (Axis’ ActiveX component software required for Microsoft Internet

Explorer). Java Applet as alternative to ActiveX.

Compression and Performance -

The AXIS 2120 delivers Motion-JPEG images at up to 25 images per second, as well as single JPEG images that feature user controlled compression

levels. See also Picture frequency for Networking Applications, on page 30.

73

All specifications are subject to change without prior notice.

74

Index

Index

A

Access rights 25

ActiveX 14

Anonymous user access 25

AppleTalk 61

ARP 56

ARTPEC-1 7, 72

Assigning an IP address 12

Audio Configuration 48

AXIS 2191 Audio Module 45

AXIS IP Installer 59

B

Boa Web server 7

BOOTP 59

Browsers 14

C

CGI scripts 6

Compression 7, 30

Configuring the camera 21

Connectors 63

Custom web pages 69

D

Description 8

Dial-up Networking connection 18

Digital input and output 65

Digital output 65

E

E-mail 6

Ethernet address 59

ETRAX-100 7, 72

F

Factory Default Settings 28

Firewalls 68

AXIS 2120 User’s Manual

Firmware 62

Focus Assistant 39

Focus Quality 40

Focus Ring 39

H

Home page 14

HTTP 6

I

I/O Connector 9

Installation

Camera 12

The AXIS 2191 Audio Module 47

Wizard 22

IP address

assigning 12

number of available 67

troubleshooting 56

IP setup methods 59

J

Javascript 21

L

Linux 7, 72

Lock Ring 39

M

Macintosh users 61

Modem connection 20

Modem installation 15

Motion Detection 26

Mounting assembly 11

N

Network

Connector 9

Indicator 9

Installation 12

Network Address Translation 67

Null Modem Cable 15

AXIS 2120 User’s Manual

O

Obtaining updated firmware 62

Other IP setup methods 59

P

Performance 73

Power indicator 51, 56

Power supply connector 9

PPP 7

Profile sliders - motion detection 27

Properties - Dial-up networking 19

R

Routers 68

RS-232

connector 9

connector diagram 64

S

Serial number 8

SMTP 6

Status Indicator 39

System Requirements 72

T

Technical specifications

AXIS 2120 72

AXIS 2191 52

Tools overview 24

Triggering images 65

Troubleshooting

AXIS 2191 Audio Module 51

General 54

U

Updating 62

User access rights 25

W

Wide/Tele Zoom 39

Window - motion detection 27

WinGate 68

X

xDSL 67

Index

75

76

AXIS 2120 User’s Manual

Glossary of Terms

ActiveX - A control (or set of rules) used by a browser.

ActiveX controls are often downloaded and installed automatically as required.

ARP - Address Resolution Protocol. A protocol for assigning an IP address to a physical device address that is recognized in the local network. The ARP command can be used to set the IP-address for your product.

ARTPEC - Axis Real Time Picture Encoder - used for image compression.

BOOTP - A protocol that can automatically configure a network device (give it an IP address).

Bps - Bits per second. A unit for measuring speeds in networks. A LAN might run at 10Mbps or 100Mbps.

CGI - Common Gateway Interface. A set of rules (or a program) that allows a Web Server to communicate with other programs.

DSL - Digital Subscriber Line. A means of transferring data via standard phone lines.

Ethernet - A widely used networking standard.

ETRAX - Axis' own microprocessor.

Firewall - A virtual barrier between a LAN (Local Area

Network) and other networks, e.g. the Internet.

Frame Grabber card - Plug-in hardware for "grabbing" images

FTP - File Transfer Protocol. Used for simple transfer of files to and from an ftp-server.

HTML - Hypertext Mark-up Language. Used widely for authoring documents viewed in web browsers.

HTTP - Hypertext Transfer Protocol. The set of rules for exchanging files (text, images, sound, video, and other files) on the World Wide Web.

Intranet - A private network limited to an organisation or corporation. Usually closed to external traffic.

IP - Internet-Protocol. See TCP/IP.

IP number (address) - A unique number used by a computer on the network to allow it to be identified and found.

JPEG - A standard image format, used widely for photographs. Also known as JPG.

LAN - A local area network (LAN) is a group of computers and associated devices that typically share common resources within a limited geographical area.

Linux - A popular operating system, that is “open source”

AXIS COMMUNICATIONS

Lux - A standard unit for light measurement.

NWAY - A network protocol that automatically negotiates the highest possible common transmission speed between two devices.

Null Modem Cable - A cable used for connecting a PC to a serial device, using the modem protocol for communication.

PING - A small utility used for sending data packets to network resources to check that they are working and that the network is intact.

PPP - Point-to-Point Protocol. A method allowing one computer to connect to another, usually via a modem over a phone line.

Pre/post alarm image - The images from immediately before and after an alarm.

Protocol - A special set of rules governing how two entities will communicate. Protocols are found at many levels of communication, and there are hardware protocols and software protocols.

SMTP - A common e-mail protocol.

TCP/IP - Transmission Control Protocol/Internet Protocol. A suite of network protocols that determine how data is transmitted.

TCP/IP is used on many networks, including the Internet. TCP keeps track of the individual packets of information and and IP contains the rules for how the packets are actually sent and received.

URL - Uniform Resource Locator. An "address" on the network.

V.90 - An operating standard for telephone modems.

WAN - Wide-Area-Network. Similar to a LAN, but on a larger geographical scale.

Web server - A program on a computer that delivers the resources (usually web pages) requested by the web user (the client).

Wizard - A program designed specifically to guide the user through a procedure. Typically used for installations and configurations.

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals