advertisement
3 Replacement of Main Parts
3-2 X Axis Motor_Replacement (Referential Time : 20 minutes)
1
Remove the X Axis Rail Cover, Rail Cover and Right
Side Cover.
X Axis Rail Cover
Right Side Cover
2
Move the Head Carriage to the left end.
Remove the X Motor Cable from the XY Junction
Board.
Rail Cover
XY Junction Board
3
X Motor
Cable
Flange
Spring
3
Remove the Spring and after that remove the screws fixing the Flange.
Drive Belt
There are the collars on the lower left and upper right side of the screws. Be careful not to lose them.
Screws with the collar
4
Remove the X Motor together with the Flange from the Drive
Belt.
Drive Belt
X Motor
Screws
37
3
3 Replacement of Main Parts
5
Loosen the Set Screws and remove the X Motor Pulley from the X Motor. Then, remove the X Motor from the Flange and change it to the new one.
X Motor
Pulley
X Motor
When fixing the Motor Flange, be careful with the direction of the X Motor and the Flange.
Fix the Flange to the X Motor while taking care with the cable direction and the bending part of the Flange as the figure.
Set Screws
Flange
<Bottom View>
Cable Direction
Bending
Part
X Motor Cable
X Motor
Flange
X Motor Pulley
It is necessary to press the X Motor Pulley downward against the X Motor Shaft as the figure.
X Motor Shaft
6
Fix the X Motor Pulley to the X Motor with the Set Screw.
It is necessary to fix the Set Screw against the D-
Cut part of the X Motor Shaft.
X Motor
Pulley
<Top View>
Set Screws
D-Cut part
X Motor Shaft
38
3 Replacement of Main Parts
7
Put through the X Motor Pulley to the Drive Belt.
Then, tighten up the Screws with the collar and the other
Screws temporarily to the Motor Flange.
Drive Belt
Flange
8
Attach the Spring and tighten up the screws.
Screws with the collar
Flange
Screws
3
Drive Belt
9
Connect the X Motor Cable to the XY Junction Board.
Spring
XY Junction
Board
<X Axis Load Check>
10
Turn on the Power while pressing the [ ], [ ], [ ] keys to enter the Service Mode.
Select the [LOAD] menu by pressing the [MENU] key and press [ENTER] key.
X Motor Cable
[ ], [ ], [ ] + POWER ON
[MENU] key
CHECK MODE
LOAD CON. CARD
[ENTER] key
39
3 Replacement of Main Parts
11
Select the [AXIS X] in the [LOAD] menu and press [ENTER] key. Then, Carriage moves to the Limit Position.
Enter the value 500 and press the [ENTER] key.
AXIS X Y Z S
[ENTER] key
AXIS X Y Z S
VALUE 500
[ENTER] key
AXIS X Y Z S
VALUE 500 OK
3
12 After setting the value, the load check starts.
The Carriage moves in the X direction to check the load.
40
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 4 ACCESSORIES
- 5 FRAME & CONTROLLER
- 7 X AXIS
- 9 Y AXIS
- 11 Z AXIS
- 13 WIRING MAP
- 14 MAIN BOARD ASS’Y
- 22 PANEL BOARD ASS’Y
- 29 OTHER CIRCUIT BOARS
- 37 SPINDLE MOTOR_REPLACEMENT
- 40 X AXIS MOTOR_REPLACEMENT
- 44 Y AXIS MOTOR_REPLACEMENT
- 48 Z AXIS MOTOR_ REPLACEMENT
- 53 X AXIS LM GUIDE_REPLACEMENT
- 57 Y AXIS LM GUIDE_REPLACEMENT
- 62 X BELT_REPLACEMENT
- 67 Y BELT_REPLACEMENT
- 71 Special Tools
- 72 SERVICE MODE
- 75 HOW TO UPGRADE FIRMWARE
- 78 X BELT TENSION ADJUSTMENT
- 80 Y BELTTENSION ADJUSTMENT
- 82 RIGHT ANGLED ADJUSTMENT OF X RAIL
- 83 CALIBRATION
- 86 4-8 X AXIS LOAD CHECK
- 87 4-9 Y AXIS LOAD CHECK
- 88 4-10 Z AXIS LOAD CHECK
- 89 OPERATIONAL SEQUENCE
- 91 SENSOR MAP
- 92 POOR ENGRAVING RESULT
- 94 NOISE
- 95 SPINDLE LOCK
- 96 MOTOR ERROR (X, Y, Z Axis)
- 97 INSTALLATION CHECK LIST
- 101 MAINTENANCE CHECK LIST
- 102 Specification