advertisement
H.320
This menu contains the following configuration settings:
• Audio Number = Video Number:
In a non-aggregated ISDN call, the audio number may be different from the video number.
If this checkbox is not selected, the System will request the video number and offer by default the same number as the one used by audio.
• Additional Calls:
Select automatic or manual configuration of additional calls
• Mode:
Allows you to set the call mode to 64K or 56K.
• TCS4 Delimiter definition of TCS4 calls delimiter: “#” or “*”. TCS4 is a special routing method for direct video call when a Gateway is present on the network (ISDN network to
IP network). To place a call using a TCS4 extension, do the following:
1. Obtain the following information: Gateway number, delimiter and TCS4 extension.
2. Dial the Gateway number, the delimiter and the TCS4 extension.
Example: ISDN_Gateway_number# TCS4_extension.
Broadcast
This menu contains the following configuration settings:
• This option allows you to set a transmission as “broadcast” (without capabilities exchange).
Note
In order to make a Broadcast call, the two terminals must have the same audio, video, rate and Data(LSD) configurations.
Display Status Bar and Transparency
• STATUS BAR:
Allows you to personalise the System graphical interface, choosing whether you want the status bar to be present and, if so, what information should be displayed on it.
Information on the status bar:
Date and Time, selected camera, channel status, charges, data channel.
• TRASPARENCY: allows you to add transparency to graphical pages where the video window is not reduced in size.
This transparency can be set to four different preset levels (high=75% transparency, medium=50%, low=25%, opaque=0%). Transparency can be used in different ways:
1) Automatic: (default) Only the diagnostic pages of the “Connection state” uses transparency with a selectable initial level (default medium). The transparency level can be changed dynamically.
2) Variable: All pages where no video is present use a selectable initial transparency level (default medium). The transparency level can be changed dynamically.
3) Fixed: All pages where no video is present use a selectable initial transparency level (default medium). The transparency level cannot be changed dynamically.
4) Off: Transparency is always deactivated.
Dynamic change of transparency level is achieved by pressing the remote control key C. The transparency is always deactivated when a page is superimposed with a message page to improve legibility.
30
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 6 SAFETY RULES
- 7 ABOUT THIS MANUAL
- 8 ABOUT VEGA X5 SYSTEM
- 10 REMOTE CONTROL
- 13 CABLING SCHEME
- 14 VIDEOCONFERENCE TIPS
- 15 SYSTEM POSITIONING AND INSTALLATION
- 17 OPERATION AND USE
- 23 Dual Video Connection
- 24 Dual Video Disconnection
- 24 Entering Names in the Phonebook
- 25 Modifying and Erasing Phonebook Entries
- 25 Connecting to a global Remote Phonebook
- 28 SYSTEM CONFIGURATION - SETTINGS
- 28 Control panel
- 28 Display
- 29 Screensaver
- 29 Remote control
- 29 Call-Answer-Mode
- 29 General
- 30 Broadcast
- 30 Display Status Bar and Transparency
- 31 Customize colors
- 32 Audio
- 32 Inputs
- 32 Processing
- 32 Outputs
- 33 Video Quality
- 33 Cameras
- 33 Settings
- 33 Customize
- 33 Driver
- 34 Monitor
- 34 Settings
- 35 PiP-PaP
- 36 Plasma
- 41 Data Channels
- 42 Password
- 42 Encryption
- 43 Licenses
- 44 Terminal Settings
- 44 Network interface
- 45 ISDN network interface
- 46 Access Configuration (ISDN BRI Euro)
- 46 Access configuration (ISDN BRI National)
- 46 Access configuration (ISDN PRI Euro)
- 47 Access configuration (ISDN PRI National)
- 48 NIC network interface
- 48 G.703 interface configuration(option whit license)
- 49 NIC (V.35/RS449/RS530/X21) Interface Configuration (Licence Required—see “Licences” for more information)
- 50 IP configuration
- 50 IP Configuration
- 52 H323 Settings
- 52 SIP Settings
- 53 Services
- 56 PPPoE
- 56 Enable network
- 57 Location
- 57 Load default settings
- 59 Slides storage
- 59 Slides recall via WEB client
- 59 Saving slides on a PC
- 60 Technical Specification MCU
- 61 Multiconference Setup
- 62 How to start a multiconference
- 65 Multiconference Management
- 65 MCU control panel icons
- 68 Terminals status during a MCU
- 68 Ending a Multiconference
- 69 Dual Video in MCU
- 69 Terminal test
- 70 Interfaces
- 70 Connection Status
- 71 Hardware
- 71 Software Release
- 72 CONNECTING A PERSONAL COMPUTER
- 73 REMOTE MANAGEMENT
- 74 UPDATING SOFTWARE
- 75 DATA CONFERENCE WITH MICROSOFT NETMEETING 3.XX
- 76 Managing the DataConference software
- 77 APPENDICES
- 83 TROUBLESHOOTING PROBLEMS