- Industrial & lab equipment
- Electrical equipment & supplies
- Batteries & accessories
- Battery chargers
- AWG
- DUAL USB POWER CHARGER FOR NDS LITE
- Installation manual
advertisement
AXYS ® Intellivox 808/1608 Installation Manual Rev 1.1
AUDIo INPUTS
The IntelliAmp is normally* fitted with two transformerbalanced line inputs. Selection of Input 1 and/or Input 2 as audio source is made from the WinControl software via the network, and for most installations only Input 1 need be wired. However, Input 2 may be connected to a secondary signal path (in case of a failure elsewhere in the system), or to an emergency sound source.
Inputs 1 and 2 are available on the 6p male WAGO connector on the rear panel, but Input 1 is paralleled to a
3-pin female XLR on the front panel; this is usually reserved for use during a temporary installation set-up, but may used as the permanent audio input if more convenient.
Audio 1 is also wired to an adjacent 3-pin male XLR, allowing audio to be looped to further IntelliAmps where required.
For optimum results only use good quality balanced audio cable consisting of a twisted pair and an overall screen.
The audio source(s) (e.g. the AXYS ® Octadrive) should have a low impedance balanced output. The nominal line input level is 0 dBV.
The front and rear panel audio connector pinout is as follows:
Xlr CoNN (front)
PIN No.
1
2
3
FUNCTIoN
Line 1 Screen
Line 1 +
Line 1 -
If the source equipment has a well-designed balanced output and the wiring strategy shown below is used, there should be no problems with hum or other extraneous noise.
Note that pins 3 and 6 of the audio connector are analogue audio grounds, they should be used only for connecting the screen of the audio cables, and for no other purpose.
1
3
2
Balanced source output (e.g. XLR) fig.8.2 - Balanced audio connections
3
4
1
2
5
6
LINE 1+
LINE 1 -
LINE 1 SCN
IntelliAmp line level audio input
(Line 1 only shown) or
1 2 3 4 5 6 fig.8.1 - Audio input connections
6 5 4 3 2 1
Due to the complex architecture of some large audio systems, unexpected hum or noise may occur due to ground loops, or injected noise from other equipment elsewhere in the system. If this occurs, please refer to the appendix of this manual and/or the JBL website, where additional guidance on grounding strategies will be found, with general techniques that may be applied in order to reduce ground-induced noise.
PIN No.
4
5
6
1
2
3
+2
-2
G2
+1
-1
G1 lABEl
WAGo CoNN (rEAr)
STANDArD VErSIoN
1 X 70 V/100 V
1 X lINE VErSIoN
DUAl 70 V/100 V
VErSIoN
Line level audio input 1
(0 dBV)
Line 1 +
Line 1 -
Line 1 Screen
70 V/100 V
70 V/100 V +
70 V/100 V input*
GND (n/c)
70 V/100 V
70 V/100 V +
70 V/100 V input*
GND (n/c)
Line level audio input 2
(0 dBV)
Line 2 +
Line 2 -
Line 2 Screen
Line level audio input
(0 dBV)
Line +
Line -
Line Screen
70 V/100 V
70 V/100 V +
70 V/100 V input
GND (n/c)
*See footnote on Page 8
201112/IvxHPIM_v1.1
11
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 2 Reference to Statements of Conformity
- 2 User’s Notice and disclaimer
- 4 1. Important Safety Instructions
- 5 2. Introduction
- 5 Applicable models and variants
- 6 What’s in the packaging
- 7 3. Installation Guide
- 7 Preparing for Installation
- 7 Signal and Control cables
- 8 Mechanical Installation of the Amplifier
- 9 Connector and wiring details
- 9 AC Mains
- 10 WAGO connectors
- 11 Audio inputs
- 12 Network connection
- 13 Fault monitoring relay connector
- 14 External Ambient SPL/Temperature Sensor
- 15 Loudspeaker connections
- 15 Cable Specifications
- 16 Mechanical Installation of the Loudspeaker
- 18 - Mounting Procedure
- 19 4. System checks
- 19 Connecting the PC to the IntelliAmp
- 20 Settings file upload
- 22 5. Appendix
- 22 Optional accessories
- 23 Common analogue grounding issues
- 23 Software and firmware updates
- 23 Network cables