- Industrial & lab equipment
- Electrical equipment & supplies
- Batteries & accessories
- Battery chargers
- AWG
- DUAL USB POWER CHARGER FOR NDS LITE
- Installation manual
advertisement
AXYS ® Intellivox 808/1608 Installation Manual Rev 1.1
4. SYSTEM CHECKS
After installation and connection are complete, the installer should upload the settings file into the IntelliAmp with
WinControl software. The upload procedure will verify the system’s correct operation.
This section of the manual describes the file upload procedure. It assumes that a laptop (or other computer) with both WinControl software and a driver for the RS-485 interface already installed is available, together with the
AXYS ® (or other suitable) RS-485 interface. It also assumes that the installer has the settings files, prepared by the system designer, for each Intellivox loudspeaker making up the system. These may be elsewhere on the laptop’s hard drive, or may be supplied separately on removable media such as a memory stick or a CD-ROM. No previous knowledge of WinControl is necessary, but basic familiarity with Windows file handling is required.
A full description of WinControl is beyond the scope of this manual and further information is available in the application’s Help files. Instructions on how to install
WinControl on a PC are included with the Program Set.
Instructions on the use of the AXYS RS-485 interface are included with the interface itself.
CoNNECTING THE PC To THE INTEllIAMP
The PC connects to the IntelliAmp via an RS-485 interface adapter. (Two versions of adapter are available from
AXYS ® , for connecting to PCs either via a USB or an RS-
232 port).
The most convenient method of connecting to the
IntelliAmp is usually via the 5-pin XLR on the front panel.
Use either a 5-pin XLR to 5-pin XLR cable or a 5-pin XLR to 9-pin Dsub cable. These cables are supplied with the
WinControl Program Set, the type depends on the RS-485 interface type*. Alternatively, the IntelliAmp’s RS-485 network port may be accessed via the rear panel WAGO connector; (this may be a simpler option in situations where multiple amplifiers have been interconnected as all amplifiers may be addressed from a single PC access point). There is no difference in functionality between the front and rear panel RS-485 connectors.
The RS-485 interface should then be connected to either the PC’s 9-pin COM port (in the case of a RS-232 to
RS-485 interface) or a USB port (in the case of a USB to
RS-485 interface).
* Cables to connect the RS-485 interface to the Intellivox system may also be ordered separately from JBL – see page 22 for ordering information.
201112/IvxHPIM_v1.1
19
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 2 Reference to Statements of Conformity
- 2 User’s Notice and disclaimer
- 4 1. Important Safety Instructions
- 5 2. Introduction
- 5 Applicable models and variants
- 6 What’s in the packaging
- 7 3. Installation Guide
- 7 Preparing for Installation
- 7 Signal and Control cables
- 8 Mechanical Installation of the Amplifier
- 9 Connector and wiring details
- 9 AC Mains
- 10 WAGO connectors
- 11 Audio inputs
- 12 Network connection
- 13 Fault monitoring relay connector
- 14 External Ambient SPL/Temperature Sensor
- 15 Loudspeaker connections
- 15 Cable Specifications
- 16 Mechanical Installation of the Loudspeaker
- 18 - Mounting Procedure
- 19 4. System checks
- 19 Connecting the PC to the IntelliAmp
- 20 Settings file upload
- 22 5. Appendix
- 22 Optional accessories
- 23 Common analogue grounding issues
- 23 Software and firmware updates
- 23 Network cables