Base and trunk card installation. Avaya B5800

Base and trunk card installation

Procedure

1. Rename the music file holdmusic.wav.

2. Using a card reader, copy the file into the /system/primary folder on the System

SD memory card.

3. If the B5800 Branch Gateway system is configured for additional music-on-hold files

(up to 3 additional files), copy those files to the same location.

The name of the additional files must match those specified in the B5800 Branch

Gateway system configuration.

Base and trunk card installation

The base cards and trunk daughter cards should be fitted before power is applied to the control unit. Ensure that cards are inserted in the order that matches the planned or pre-built configuration. In general, the following applies to card installation:

• Cards can be fitted in any order into any available slots. The only exception is the 4-port expansion card which can only be installed in right-hand slot 4.

• It is recommended that cards are fitted from left to right.

• There are restrictions to the number of supported cards of some types. When a limit is exceed, the right-most card of that type will not function.

• Ensure that you use the labels supplied to identify the card fitted into the control unit.

Warning:

• Correct anti-static protection steps should be taken before handling circuit boards.

• Cards must never be added or removed from the control unit while it has power connected.

Trunk daughter card preparation

Trunk daughter cards can be fitted to any base card except the legacy card carrier. For combination cards, the trunk daughter card is pre-installed and cannot be changed.

Implementing B5800 Branch Gateway for a CS 1000 Configuration October 2012 61

Hardware and software installation

Warning:

Correct anti-static protection steps should be taken while handling circuit boards.

Parts and equipment required

• Base card (except the legacy card carrier)

• Trunk daughter card

• 3 stand-off pillars (these are supplied with the trunk daughter card)

Tools required

• 5mm Flat-blade screwdriver

• Anti-static wrist strap and ground point

Installing a trunk daughter card

Procedure

1. Check that correct cards have been supplied.

62 Implementing B5800 Branch Gateway for a CS 1000 Configuration

Comments? [email protected]

October 2012


2. Ensure that you are wearing an anti-static wrist strap connected to a suitable ground point.

3. On the base card, identify the position of the 3 holes for the plastic pillars for the trunk daughter card.

These are along the same edge as the card connector.

4. Fit the stand-off pillars to the base card.

5. If there is a clip-on metal shield over the connector block on the base card, remove it.

6. Using minimal force and checking that the pins are correctly located, push the trunk card onto its connector block and the stand-off pillars.

7. Check that the card connector has snapped into position.

8. Using the washers and screws provided, secure the metal stand-off pillars to the base card.

9. From the set of labels that are supplied with the trunk daughter card, fit the appropriate label to the front of the base card.

Legacy carrier card preparation

A legacy carrier card can be used to fit VCM cards into the B5800 Branch Gateway control unit. Up to 2 legacy carrier cards can be inserted. The following trunk and VCM cards are supported. Cards not listed are not supported.

• PRI T1

• Dual PRI T1

• PRI 30 E1 (1.4)

• Dual PRI E1

• PRI 30 E1R2 RJ45

• Dual PRI E1R2 RJ45

• BRI-8 (UNI)

• ANLG 4 UNI (US only)

• VCM 4

• VCM 8

• VCM 16

• VCM 24

• VCM 30



Warning:

Correct anti-static protection steps should be taken while handling circuit boards.

Parts and equipment required

• Legacy carrier card

• VCM card

• 2 plastic stand-off pillars per card

• Trunk cards are supplied with a replacement blanking plate which is not required.

Tools required





October 2012


Installing a legacy carrier card

Procedure

1. Check that correct cards have been supplied.

2. Ensure that you are wearing an anti-static wrist strap connected to a suitable ground point.

3. On the carrier card identify the position of the jumper block and stand-off pillar holes for the IP400 card.

The peg holes are labeled as VCM or TRUNK.

4. If fitting an IP400 trunk card, identify which of the plastic snap-off panels on the front of the carrier card need to be removed to allow the trunk cable connections.

5. Carefully remove those panels.

6. Fit the stand-off pillars to the legacy carrier card.

7. Using minimal force and checking that the pins are correctly located, push the IP400 card onto its jumper and the stand-off pillars.

Base card insertion

Having prepared each base card by adding the trunk daughter cards or legacy carrier cards, the base card can be inserted into the control unit.



Warning:

• Correct anti-static protection steps should be taken before handling circuit boards.

• Cards must never be added or removed from the control unit while it has power connected.

• Tools required



Installing a base card

Procedure

1. Check that there is no power to the control unit.

2. Using a flat-bladed screwdriver, remove the cover from the slot on the front of the control unit that will be used for each card being installed.

This cover is no longer required but should be retained until installation has been completed.

3. Allowing the card to rest against the bottom of the slot, begin sliding it into the control unit.

4. When half inserted, check that the card rails have engaged with the slot edges by trying to gently rotate it. If the card rotates, remove it and begin inserting it again.

The card should slide in freely until almost fully inserted.



October 2012

Base and trunk card installation. Avaya B5800

Base and trunk card installation

Trunk daughter card preparation

Installing a trunk daughter card

Legacy carrier card preparation

Installing a legacy carrier card

Base card insertion

Installing a base card

Related manuals

Table of contents

Base and trunk card installation. Avaya B5800