advertisement
3.5 Extended setting
This part is designed for system setting which are done once during installation or when are problems with device kompatibility.
3.5.1 DoorPhone
After performing of changes please don’t forget click on „Save“.
Ringing timeout – time for which is ringing. When is setup more numbers as same as progressive ringing then after this time ringing is ended on first phone number (IP adress in P2P) and starts ringing on second. It is time until which subscriber must pick up. When is not next number to call then email is sent either to email adress mentioned in phone book or to default email (E-mail setting).Setting range is 5 to 300sec (6min.) caution: it might happen that ringing time will not be limited but it is limited by time parametres of SIP protocol and it is usually 2-5min
IP BOLD - installation and operating instructions 61
(according SIP device setting). You can record message to SD card during this time and simultaneously send email.
Maximum call duration – when call is picked up timer for call duration limit is activated. When you insert empty, then there is no limit. The 10sec before call end you hear tone after which you can dial character for call prolongation and by this prolong the call about same time period.
Prolongation key – options are * or # and usage is descriped in „Maximal call duration ”
( Reject all incomming calls – move to the SIP settings)
Ringing cycles count – this option enable repeating of call (or progressive call).
In phone book is for example filled first and second phone number and not create group. When come condition for first number: time is out
- phone number is busy
- ringing
- subscriber is not reachable / registrated in network
Then second number is dialled. When the same conditions come true and ringing cycles are setup 2 the whole cycle is repeated one more time.
Same key pressed again – when you press again the same button then you setup door entry behaviour. Options are:
- call is hang up
- call is repeated
- nothing happen
Another button is pressed - if you press a different key during a call than you originally pressed, the doorphone behavior is selected:
- dial the telephone number at the currently pressed button
- ignore and nothing happens
Active button by HTTP – if checked, so is possible use http request for remote activation button (like as press the button. This feature is for easy check the installation IP BOLD.
Example : http:// IPaddress /button_control?btn=1 - remote activate button 1 http:// IPaddress /button_control?btn=27 - remote activate button 27
Dialling timeout – this time concern buttons (keypad) and it is deciding for correct code inserting. When space between button press is longer than this time the code is not correctly evaluated . Situation:
- code keylock provides correct code evaluation
- number dial from keypad –dial end resolution
This time simultaneously prolong dial time at buttons which are initial numbers of codes.
DTMF dialling timeout – this time concerns incoming calls from telephones and it is deciding for correct code inserting . The principle is the same as previous parametr but it concerns codes from telefone.
Keyboard mode – models TK only – memory number dial means that you press 1-3 digit code on keypad which determined position in phone book (1-999). The door
entry process the call same way as you pressed
62 IP BOLD - installation and operating instructions
button on door entry (1-999). Direct phone numbers dial means that you dial numbers by keypad as on ordinary phone.
When you have in numbers dial space longer than maximal number inserting time then door entry calls. When you want in mode P2P call to IP adress then „ .
” in IP adress is substitute by .
Camera light – wideangle camera has posibility of extra lighting when light conditions are not acceptable. The lighting provils by white LEDs
(unfortunately infra LED cant be used but advantage is fully colour picture). The door entry has dark sensor and you have following options of lighting:
- OFF, LEDs will never light
- during conversation, LEDs are allways lighting during call independently on surrounding light conditions
- in the night, LEDs are lighting according surrounding light conditions independently on call
- during night call , Led svítí pouze při hovoru a podle okolního osvětlení
Light intensity – here you setup LEDs light intensity
Labels light – name card might be backlighted by 3 ways:
- OFF, name cards will never be back lighted
- in the night , backlighting depends on surrounding light
- name card is permanently back lighted
Light intensity - here you setup backlight intensity
Daylight lower treshold – settings sensitivity ambient light sensor, the lower limit of the window comparator (range 1-1021)
Daylight upper treshold - setting sensitivity ambient light sensor, the upper limit of window comparator (range 1-1021)
ATTENTION The lower limit must always be less than the upper limit, as the difference between the two values is the hysteresis (recommended to maintain approximately 50)
IP BOLD - installation and operating instructions 63
advertisement
Related manuals
advertisement