Q Corresponding Serial Communication Module User's Manual

2 SYSTEM CONFIGURATION AND AVAILABLE FUNCTIONS

MELSEC-Q

2 SYSTEM CONFIGURATION AND AVAILABLE FUNCTIONS

This Chapter describes the system configuration and available functions.

2.1 Applicable Systems

The following describes applicable systems.

(1) Applicable modules and number of modules that can be mounted

The following table lists the CPU module and network modules (for remote I/O stations) that the Q series C24 can be mounted and the number of modules which can be mounted.

Applicable module

Number of modules that can be installed

Maximum 8

Remarks

CPU module

Network module

Q00JCPU

Q00CPU

Q01CPU

Q02CPU

Q02HCPU

Q06HCPU

Q12HCPU

Q25HCPU

Q12PHCPU

Q25PHCPU

QJ72LP25-25

QJ71LP25GE

QJ72BR15

Maximum 24

Maximum 64

Maximum 64

Maximum 64

(

(

(

1

)

Can be installed in Q mode only

1

)

1

)

MELSECNET/H Remote I/O station (

2

)

1 See User's Manual (Function Explanation, Program Fundamentals) for the CPU module to use.

2 See Q Corresponding MELSECNET/H Network System Reference Manual (Remote I/O network).

(2) The base module to which the Q series C24 can be mounted

The Q series C24 can be mounted into any I/O slot ( 1) of the base module.

1 Limited to within the range of I/O points for the CPU module and network module (for remote I/O station)

(3) Multiple CPU systems

When using the Q series C24 on a multiple CPU system, refer to the QPU User's

Manual (Multiple CPU System) before operation.

(a) Applicable Q series C24

If using the Q series C24 on a multiple CPU system, use function version B of the Q series C24.

(b) Intelligent function module parameter

To write the intelligent function module parameter on a PLC, be sure to write it in the Q series C24 control PLC only.

2

2 - 1 2 - 1

2

2 SYSTEM CONFIGURATION AND AVAILABLE FUNCTIONS

MELSEC-Q

(4) Applicable software packages

(a) Software/setting & monitor tools ( 1) for the PLC

The following table lists the systems and software packages applicable for the Q series C24.

When using the Q series C24, GX Developer is required.

Q00J/Q00/Q001CPU

Q02/Q02H/Q06H/

Q12H/Q25HCPU

Q12PH/Q25PHCPU

Single CPU system

Multiple CPU system

Single CPU system

Multiple CPU system

Single CPU system

Multiple CPU system

GX Developer

Software packages

GX Configurator-SC

Version 7 or later

Version 8 or later

Version 4 or later

Version 6 or later

Version 7.10L or later

Version 1.0 or later

(Versions prior to SW0D5C-

QSCU-E 40E are not usable.)

SW0D5C-QSCU-E 00A or later

SW0D5C-QSCU-E 20C or later

Version 1.13P or later

(Versions prior to SW0D5C-

QSCU-E 40E are not usable.)

When installing an MELSECNET/H remote I/O station

Version 6 or later SW0D5C-QSCU-E 30D or later

1 See section 2.6 for the versions of the GX Developer and GX Configurator-SC that support the functions added through improvements in the Q series C24.

(b) Communication support tools for external devices

Item Name Model

MX Component SWnD5C-ACT -E

Remark

ActiveX control library.

The "n" in the model name is 0 or greater. (

1

)

1 Depending on the version of MX Component used, different versions of Q series C24 are supported.

See the manual of MX Component for the details.

2 - 2 2 - 2