advertisement
Figure 3-3 Browsing MIB-II OIDs of Super Series SNMP agent using SNMP Browser
(AdventNet MibBrowser)
3.3. Dynamic DNS Configuration
When users connect the Super Series to a DSL line or use a DHCP configuration, the IP address might be changed whenever it reconnects to the network. It can therefore be very difficult to post all related contacts for each new IP address. In addition, if the administrator only has access through the remote console, there is no way to know if an IP address has changed, or what the new IP address is.
A Dynamic DNS service is provided by various ISPs or organizations to deal with the above issue. By using the Dynamic DNS service, users can access the Super Series through the hostname registered in the Dynamic DNS Server regardless of any IP address change.
By default, the Super Series only supports Dynamic DNS service offered at Dynamic DNS Network
Services, LLC ( www.dyndns.org
). Contact Sena technical support for issues regarding other Dynamic
DNS service providers.
To use the Dynamic DNS service provided by Dynamic DNS Network Services, the user must set up an account in their Members' NIC (Network Information Center http://members.dyndns.org
). The user
31
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 8 1.1. Overview
- 9 1.2. Package Check List
- 9 1.3. Product Specification
- 10 1.4. Terminologies And Acronyms
- 13 2.1. Panel Layout
- 13 2.1.1. SS100 Panel Layout
- 14 2.1.2. SS110 Panel Layout
- 15 2.1.3. SS400 Panel Layout
- 16 2.1.4. SS800 Panel Layout
- 16 2.2. Connecting The Hardware
- 16 2.2.1. Connecting The Power
- 17 2.2.2. Connecting To The Network
- 18 2.2.3. Connecting To The Device
- 19 2.2.4. Accessing The System Console
- 20 2.2.5. Using The System Console
- 22 2.2.6. Using Remote Console
- 23 2.3. Accessing The Web Browser Management Interface
- 25 3.1. IP Configuration
- 26 3.1.1. Using A Static IP Address
- 27 3.1.2. Using DHCP
- 28 3.1.3. Using PPPoE
- 28 3.2. SNMP Configurations
- 29 3.2.1. MIB-II System Objects Configuration
- 30 3.2.2. Access Control Configuration
- 30 3.2.3. Trap Receiver Configuration
- 30 3.2.4. Management Using SNMP
- 31 3.3. Dynamic DNS Configuration
- 32 3.4. SMTP Configuration
- 33 3.5. IP Filtering
- 35 3.6. SYSLOG Server Configuration
- 35 3.7. NFS Server Configuration
- 36 3.8. Ethernet configuration
- 37 3.9. Web Server Configuration
- 37 3.10. TCP Service Configuration
- 39 4.1. Overview
- 42 4.2. Individual Port Configuration
- 43 4.2.1. Port Enable/Disable
- 43 4.2.2. Port Title
- 44 4.2.3. Apply All Port Settings
- 45 4.2.4. Host Mode Configuration
- 54 4.2.5. Remote Host Configuration
- 54 4.2.6. Port IP Filtering Configuration
- 55 4.2.7. Cryptography Configuration
- 60 4.2.8. Filter Application
- 61 4.2.9. Serial Port Parameters
- 64 4.2.10. Modem Configuration
- 65 4.2.11. Port Logging
- 66 4.2.12. Port Event Handling Configurations
- 70 4.3. All Port Configurations
- 73 5.1. LAN Card Configuration
- 74 5.2. Wireless LAN Card Configuration
- 76 5.3. Serial Modem Card Configuration
- 76 5.4. ATA/IDE Fixed Disk Card Configuration
- 77 6.1. System Status
- 77 6.2. System Logging
- 79 6.3. User Logged On List
- 79 6.4. Change Password
- 80 6.5. Device Name Configuration
- 80 6.6. User Administration
- 81 6.7. Date And Time Settings
- 82 6.8. Configuration Management
- 84 6.9. Firmware Upgrade
- 86 6.10. Security Profile
- 86 6.11. User File Uploading
- 88 7.1. Network Interfaces Statistics
- 88 7.2. Serial Ports Statistics
- 89 7.3. IP Statistics
- 91 7.4. ICMP Statistics
- 93 7.5. TCP Statistics
- 95 7.6. UDP Statistics
- 97 8.1. Introduction
- 97 8.2. Flash Partition
- 98 8.3. Supported Linux Utilities
- 98 8.3.1. Shell & Shell Utilities
- 98 8.3.2. File and Disk Utils
- 98 8.3.3. System Utilities
- 98 8.3.4. Network Utilities
- 98 8.4. Accessing CLI As root Or System Administrator
- 99 8.5. Editing Super Series Configuration In CLI
- 99 8.5.1. Configuration file save/load mechanism
- 99 8.5.2. To Change Configuration In CLI
- 99 8.6. Running User Defined Scripts
- 100 8.7. File Transmission
- 100 8.8. Examples
- 100 8.8.1. Disabling The Telnet Port Of The Unit
- 102 8.8.2. Periodical Program Execution
- 103 9.1. Introduction
- 103 9.2. Periodical Program Execution
- 104 9.3. User Defined Web Pages
- 104 9.4. Making And Running User’s Own Code
- 105 A 1.1. Ethernet Pinouts
- 105 A 1.2. Console And Serial Port Pinouts For SS
- 106 A 1.3. Console And Serial Port Pinouts For SS
- 106 A 1.4. Ethernet Wiring Diagram
- 107 A 1.5. Serial Wiring Diagram
- 107 A 1.5.1. RS232 Serial Wiring Diagram For SS
- 107 A 1.5.2. RS232 Serial Wiring Diagram For SS
- 109 A 1.5.3. RS422/285 Serial Wiring Diagram For SS
- 109 A 1.5.4. RS422/285 Serial Wiring Diagram For SS
- 113 A 3.1. system.cnf
- 115 A 3.2. redirect.cnf
- 120 A 5.1. Overview
- 120 A 5.2. Main Menu
- 120 A 5.3. RTC Configuration Menu
- 121 A 5.4. Hardware Test Menu
- 125 A 5.5. Firmware Upgrade Menu
- 127 A 6.1. Super Series vs. Serial/IP Options
- 128 A 6.2. Connection Example - Telnet And SSLv3 Encryption
- 132 A 7.1. Install The OpenSSL Package
- 132 A 7.2. Make root CA (For Self-signed)
- 134 A 7.3. Making A Certificate Request
- 134 A 7.4. Signing A Certificate Request
- 135 A 7.5. Making Certificate For SS
- 137 A 8.1. GENERAL WARRANTY POLICY
- 137 A 8.2. LIMITATION OF LIABILITY
- 138 A 8.3. HARDWARE PRODUCT WARRANTY DETAILS
- 138 A 8.4. SOFTWARE PRODUCT WARRANTY DETAILS
- 138 A 8.5. THIRD-PARTY SOFTWARE PRODUCT WARRANTY DETAILS