advertisement
4.2.5. Remote Host Configuration
Remote host configuration is the list of hosts that will receive data from serial port of Super Series when there is data transmission from a serial port of Super Series.
In TCP mode, user can also configure secondary remote host that will receive data from serial port if
Super Series fails to connect to primary remote host. But if connection to primary remote host can be made, Super Series dose not send data to secondary remote host until connection to primary remote host failed. And the maximum possible number of primary remote host is limited up to 16.
In UDP mode, user can configure only primary remote host because there is no way for Super Series to check status of primary remote host, so secondary remote host is meaningless.
Figure 4-8 shows Remote host configuration pages of the Web UI. (TCP mode)
Figure 4-8 Remote host configuration
4.2.6. Port IP Filtering Configuration
The remote hosts that are allowed to access the Super Series serial ports can be specified based on the IP address filtering rules. The user may allow specific hosts to access the Super Series serial ports by providing a valid IP address or network address and its subnet mask. Please refer to section 3.5. IP
Filtering for more details.
54
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 8 1.1. Overview
- 9 1.2. Package Check List
- 9 1.3. Product Specification
- 10 1.4. Terminologies And Acronyms
- 13 2.1. Panel Layout
- 13 2.1.1. SS100 Panel Layout
- 14 2.1.2. SS110 Panel Layout
- 15 2.1.3. SS400 Panel Layout
- 16 2.1.4. SS800 Panel Layout
- 16 2.2. Connecting The Hardware
- 16 2.2.1. Connecting The Power
- 17 2.2.2. Connecting To The Network
- 18 2.2.3. Connecting To The Device
- 19 2.2.4. Accessing The System Console
- 20 2.2.5. Using The System Console
- 22 2.2.6. Using Remote Console
- 23 2.3. Accessing The Web Browser Management Interface
- 25 3.1. IP Configuration
- 26 3.1.1. Using A Static IP Address
- 27 3.1.2. Using DHCP
- 28 3.1.3. Using PPPoE
- 28 3.2. SNMP Configurations
- 29 3.2.1. MIB-II System Objects Configuration
- 30 3.2.2. Access Control Configuration
- 30 3.2.3. Trap Receiver Configuration
- 30 3.2.4. Management Using SNMP
- 31 3.3. Dynamic DNS Configuration
- 32 3.4. SMTP Configuration
- 33 3.5. IP Filtering
- 35 3.6. SYSLOG Server Configuration
- 35 3.7. NFS Server Configuration
- 36 3.8. Ethernet configuration
- 37 3.9. Web Server Configuration
- 37 3.10. TCP Service Configuration
- 39 4.1. Overview
- 42 4.2. Individual Port Configuration
- 43 4.2.1. Port Enable/Disable
- 43 4.2.2. Port Title
- 44 4.2.3. Apply All Port Settings
- 45 4.2.4. Host Mode Configuration
- 54 4.2.5. Remote Host Configuration
- 54 4.2.6. Port IP Filtering Configuration
- 55 4.2.7. Cryptography Configuration
- 60 4.2.8. Filter Application
- 61 4.2.9. Serial Port Parameters
- 64 4.2.10. Modem Configuration
- 65 4.2.11. Port Logging
- 66 4.2.12. Port Event Handling Configurations
- 70 4.3. All Port Configurations
- 73 5.1. LAN Card Configuration
- 74 5.2. Wireless LAN Card Configuration
- 76 5.3. Serial Modem Card Configuration
- 76 5.4. ATA/IDE Fixed Disk Card Configuration
- 77 6.1. System Status
- 77 6.2. System Logging
- 79 6.3. User Logged On List
- 79 6.4. Change Password
- 80 6.5. Device Name Configuration
- 80 6.6. User Administration
- 81 6.7. Date And Time Settings
- 82 6.8. Configuration Management
- 84 6.9. Firmware Upgrade
- 86 6.10. Security Profile
- 86 6.11. User File Uploading
- 88 7.1. Network Interfaces Statistics
- 88 7.2. Serial Ports Statistics
- 89 7.3. IP Statistics
- 91 7.4. ICMP Statistics
- 93 7.5. TCP Statistics
- 95 7.6. UDP Statistics
- 97 8.1. Introduction
- 97 8.2. Flash Partition
- 98 8.3. Supported Linux Utilities
- 98 8.3.1. Shell & Shell Utilities
- 98 8.3.2. File and Disk Utils
- 98 8.3.3. System Utilities
- 98 8.3.4. Network Utilities
- 98 8.4. Accessing CLI As root Or System Administrator
- 99 8.5. Editing Super Series Configuration In CLI
- 99 8.5.1. Configuration file save/load mechanism
- 99 8.5.2. To Change Configuration In CLI
- 99 8.6. Running User Defined Scripts
- 100 8.7. File Transmission
- 100 8.8. Examples
- 100 8.8.1. Disabling The Telnet Port Of The Unit
- 102 8.8.2. Periodical Program Execution
- 103 9.1. Introduction
- 103 9.2. Periodical Program Execution
- 104 9.3. User Defined Web Pages
- 104 9.4. Making And Running User’s Own Code
- 105 A 1.1. Ethernet Pinouts
- 105 A 1.2. Console And Serial Port Pinouts For SS
- 106 A 1.3. Console And Serial Port Pinouts For SS
- 106 A 1.4. Ethernet Wiring Diagram
- 107 A 1.5. Serial Wiring Diagram
- 107 A 1.5.1. RS232 Serial Wiring Diagram For SS
- 107 A 1.5.2. RS232 Serial Wiring Diagram For SS
- 109 A 1.5.3. RS422/285 Serial Wiring Diagram For SS
- 109 A 1.5.4. RS422/285 Serial Wiring Diagram For SS
- 113 A 3.1. system.cnf
- 115 A 3.2. redirect.cnf
- 120 A 5.1. Overview
- 120 A 5.2. Main Menu
- 120 A 5.3. RTC Configuration Menu
- 121 A 5.4. Hardware Test Menu
- 125 A 5.5. Firmware Upgrade Menu
- 127 A 6.1. Super Series vs. Serial/IP Options
- 128 A 6.2. Connection Example - Telnet And SSLv3 Encryption
- 132 A 7.1. Install The OpenSSL Package
- 132 A 7.2. Make root CA (For Self-signed)
- 134 A 7.3. Making A Certificate Request
- 134 A 7.4. Signing A Certificate Request
- 135 A 7.5. Making Certificate For SS
- 137 A 8.1. GENERAL WARRANTY POLICY
- 137 A 8.2. LIMITATION OF LIABILITY
- 138 A 8.3. HARDWARE PRODUCT WARRANTY DETAILS
- 138 A 8.4. SOFTWARE PRODUCT WARRANTY DETAILS
- 138 A 8.5. THIRD-PARTY SOFTWARE PRODUCT WARRANTY DETAILS