advertisement
MGate MB3000 Modbus Gateway Getting Started
Connecting to a Host or the Network
A 10/100BaseT Ethernet port is located on the unit’s front panel. This port is used for the unit’s connection to a host or Ethernet network, as follows:
• For normal operation, use a standard straight-through Ethernet cable to connect the unit to your Modbus
TCP network.
• For initial configuration or for troubleshooting purposes, you may connect the unit directly to a PC. In this case, use a crossover Ethernet cable to connect the unit to your PC’s Ethernet connector.
The unit’s Link LED will light up to indicate a live Ethernet connection.
For advanced models (MB 3170, MB3170I, MB3270, and MB3270I), two Ethernet ports are provided. One port can be used to connect to the network, and the other port can be used to connect to another Ethernet device.
Installing the Software
The Windows management utility is installed from the Document and Software CD. Follow the onscreen instructions after inserting the CD. For additional details, please refer to Chapter 9.
Mounting the Unit
The unit can be placed on a desktop, mounted on the wall, or mounted on a DIN-rail. The MB3180, MB3280, and MB3480 require optional attachments for DIN-rail mounting. For additional details, please refer to the hardware reference chapter for your model.
2-3
3
3.
Hardware: MB3180
This chapter provides hardware information for the MGate MB3180.
The following topics are covered in this chapter:
MGate MB3000 Modbus Gateway
Panel Layout
Hardware: MB3180
LED Indicators
Name Color
Red
Ready
Ethernet
P1 Tx/Rx
Green
Off
Orange
Green
Off
Orange
Green
Off
Function
Steady on: Power is on and unit is booting up.
Blinking: Indicates an IP conflict, or DHCP or BOOTP server is not responding properly.
Steady on: Power is on and unit is functioning normally.
Blinking: Unit is responding to software Locate function.
Power is off, or power error condition exists.
10 Mbps Ethernet connection.
100 Mbps Ethernet connection.
Ethernet cable is disconnected, or has a short.
Serial port is receiving data.
Serial port is transmitting data.
No data is being transmitted or received through the serial port.
3-2
MGate MB3000 Modbus Gateway
Dimensions
Hardware: MB3180
3-3
MGate MB3000 Modbus Gateway
Jumpers
Hardware: MB3180
To set the pull high/low resistors to 150 KΩ, leave jumpers JP3 and JP4 open (not shorted). This is the default setting.
To set the pull high/low resistors to 1 KΩ, short jumpers JP3 and JP4 with jumper caps.
ATTENTION
Do not use the 1 KΩ pull high/low setting on the MGate MB3000 when using the RS-232 interface. Doing so will degrade the RS-232 signals and reduce the effective communication distance.
3-4
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 6 Seamless integration of Ethernet and serial Modbus devices
- 6 Powerful operation modes to handle almost any Modbus application
- 6 Windows utilities for easy setup and traffic monitoring
- 9 RS-485 Termination and Pull High/Low Resistors
- 10 Connecting to a Host or the Network
- 10 Installing the Software
- 10 Mounting the Unit
- 15 DB9 (Male)
- 21 DB9 (Male)
- 33 Terminal Block (RS-422, RS-485)
- 34 Power Input, Relay Output
- 40 DB9 (Male)
- 40 Power Input, Relay Output
- 43 Connect all Modbus devices over an Ethernet network
- 43 Link a serial master device with Ethernet slave devices
- 44 Link TCP master devices with both ASCII and RTU serial devices simultaneously
- 44 Let Modbus serial devices communicate over the Internet
- 50 Change Language Setting
- 51 Broadcast Search
- 52 Specify IP Address
- 54 Configure Serial Port for RTU or ASCII, Master or Slave
- 55 What is ProCOM?
- 55 How to Configure ProCOM for the MGate MB3000
- 57 Offline Open
- 58 Configure IP Address and Other Network Settings
- 59 Configure Serial Communication Parameters
- 60 RTS Toggle
- 61 Set Up Slave ID Mapping (Smart Routing)
- 61 How Slave IDs are Mapped on the MGate MB3000
- 62 How Slave ID Map is Defined
- 62 Slave ID Map Example
- 62 Customize Modbus Settings
- 63 Initial Delay
- 63 Modbus TCP Exception
- 63 Slave Channel and Response Timeout
- 63 Inter-Character Timeout
- 63 Inter-Frame Delay
- 65 Set Up Priority Control
- 66 Accessible IP
- 67 SNMP
- 68 Miscellaneous Setup
- 71 Open Traffic Monitor Window
- 72 Filter Traffic Information
- 73 Save Log to File
- 75 MXview for the MGate MB3000 Series
- 83 Normal
- 84 Exception
- 84 Broadcast
- 84 Response Timeout