Extron System 8/10 Plus InFocus, InFocus LP 920, InFocus LP 770 projector communications kit User's manual

InFocus Installation
Configuration and Connections
SYSTEM 8/10 Plus
PROJECTOR COMMUNICATIONS KIT
ATTENTION!
PLEASE READ THIS DOCUMENT FOR IMPORTANT
INSTALLATION INSTRUCTIONS
THIS KIT HAS BEEN SHIPPED WITH THE FOLLOWING COMPONENTS:
Kit Type: INFOCUS
Included Communications Adapter(s):
Quantity
1
Part Number
26-467-01
Description
ADP, UNV, “A”
THE TABLE BELOW LISTS THE POSSIBLE CONFIGURATION(S) AND CORRESPONDING
COMMUNICATIONS ADAPTER(S) FOR YOUR PROJECTOR MANUFACTURER’S VARIOUS
MODELS. PLEASE NOTE THAT YOUR SWITCHER HAS BEEN CONFIGURED AS
INDICATED BY THE “✔” IN THE “Config as” COLUMN. IF YOUR PROJECTOR MODEL
DIFFERS FROM THIS CONFIGURATION, YOU MUST RECONFIGURE YOUR SWITCHER
WITH THE CORRECT SETTINGS.
PLEASE REFER TO THE FOLLOWING PAGES FOR COMPLETE CONFIGURATION AND
SIGNAL CONNECTION INSTRUCTIONS.
THIS SWITCHER HAS BEEN CONFIGURED FOR:
Config
as
✔
Model
INFOCUS
Rotary Switches Cable
SW15 Settings
Comm
RS1 RS2 RS3 RS4 J2/J3 1 2 3 4 5 6 7 8 9 10 Adapter
InFocus
0
0
F
7
J2
↓ ↓ ↑ ↓ ↑ ↓ ↓ ↓ ↑ ↓ 26-467-01
InFocus LP 920
1
0
F
7
J2
↓ ↓ ↑ ↓ ↑ ↓ ↓ ↓ ↑ ↓ 26-467-01
InFocus LP 770
0
0
E
D
J2
↓ ↓ ↑ ↓ ↑ ↓ ↑ ↓ ↑ ↓ 26-467-01
Extron • System 8/10 PLUS • User’s Manual • P/N 68-415-01 Rev. B
Page 1
InFocus Installation
Configuration and Connections
InFocus Projector Configuration
Verify that the System 8/10 PLUS is already configured for the InFocus projector.
The general setup is explained on page 3-4 and the switch settings for the
projector are repeated below.
1. Use a small screwdriver to remove the access cover from the System 8/10 PLUS
front panel. See bottom of page 3-3. The label on the back of the access cover
also has the configuration information.
__________ Before changing anything, remove the AC power cord to the System 8/10 PLUS
to verify that the main power is OFF; also turn the projector power OFF.
2. Set the switches as follows:
Config
Model
as
✔
Rotary Switches Cable
RS1 RS2 RS3 RS4 J2/J3
InFocus
0
0
F
7
J2
SW15 Settings
1 2
3
4
5
6
Comm
7 8
↓ ↓ ↑ ↓ ↑ ↓
9 10
↓ ↓ ↑ ↓
Adapter
26-467-01
¯
ON
_RS5 is for RGB switching
delay. See page 3-4 for
more information on switch
functions.
1
2
3
4
5
6
7
8
9
10
SW15 DIP Switch
RS2
RS3
RS5 RS2 RS1
RS4
RS1
RS3 RS4
Configured For:
RS-232
3. Use a grease pencil (or other rub-off marker) to mark the space on the label next
to “InFocus”.
4. Locate the switcher’s Address DIP switches on the rear panel, lower right. Unless
this is part of a master/slave system, set #3 and #5 to the up position and the
others down. See illustration to the left.
Use the illustration on the next page to do the following steps.
5. Connect the Comm Adapter’s 9-pin male connector to the 9-pin female “Remote
1” connector on the rear panel of the projector.
6. Connect the CC-50' (or CC-100') cable from the 9-pin male connector of the
Comm Adapter to the 15-pin HD “Projector Control” port located on the rear
panel of the System 8/10 PLUS.
______ Secure the screws on all D connectors.
7. Connect the BNC (RGBS) cables from the System 8/10 PLUS outputs to the
projector inputs according to the application requirements.
8. Apply Main Power to the System 8/10 PLUS by connecting the power cord. The
Main Power LED should light. Apply power to the projector.
9. Return System 8/10 PLUS and projector to normal operation.
Extron • System 8/10 PLUS • User’s Manual • P/N 68-415-01 Rev. B
Page 2
InFocus Installation
Configuration and Connections
InFocus Projector Connections
Use the illustration below when connecting the System 8/10 PLUS to an InFocus
projector. Refer to InFocus documentation to continue the installation.
RS 232
L
R
Volume 1
Volume 2
L
L
S-VID
R
BNC
R
BNC
L
R
R
Comp 1
H
G
Comp 2
V
B
L
R
HD 15
Comp 3
Universal
Comm Adapter
26-467-01 "A"
A
9-Pin Male
9-Pin Female
RGBHV 5 BNC
15-Pin
Male
_ If the installation includes looping (master/slave) switchers, see Chapter 5.
If Video Loop Back is part of the installation, see pages 2-10 and 2-11.
Extron • System 8/10 PLUS • User’s Manual • P/N 68-415-01 Rev. B
Page 3
InFocus Installation
Configuration and Connections
InFocus LP 920 Projector Configuration
Verify that the System 8/10 PLUS is already configured for the InFocus LP 920
projector. The general setup is explained on page 3-4 and the switch settings for
the projector are repeated below.
1. Use a small screwdriver to remove the access cover from the System 8/10 PLUS
front panel. See bottom of page 3-3. The label on the back of the access cover
also has the configuration information.
__________ Before changing anything, remove the AC power cord to the System 8/10 PLUS to
verify that the main power is OFF; also turn the projector power OFF.
2. Set the switches as follows:
Config
Model
as
Rotary Switches Cable
RS1 RS2 RS3 RS4 J2/J3
InFocus LP 920
1
0
F
7
J2
SW15 Settings
1 2
3
4
5
6
Comm
7 8
↓ ↓ ↑ ↓ ↑ ↓
9 10
↓ ↓ ↑ ↓
Adapter
26-467-01
¯
ON
_RS5 is for RGB switching
delay. See page 3-4 for more
information on switch
functions.
1
2
3
4
5
6
7
8
9
10
SW15 DIP Switch
RS2
RS3
RS5 RS2 RS1
RS4
RS1
RS3 RS4
Configured For:
RS-232
3. Use a grease pencil (or other rub-off marker) to mark the space on the label next
to “InFocus LP 920”.
4. Locate the switcher’s Address DIP switches on the rear panel, lower right. Unless
this is part of a master/slave system, set #3 and #5 to the up position and the
others down. See illustration to the left.
Use the illustration on the next page to do the following steps.
5. Connect the Comm Adapter’s 9-pin male connector to the 9-pin female “RS-232
Serial” connector on the rear panel of the projector.
6. Connect the CC-50' (or CC-100') cable from the 9-pin male connector of the Comm
Adapter to the 15-pin HD “Projector Control” port located on the rear panel of the
System 8/10 PLUS.
______ Secure the screws on all D connectors.
7. Connect the BNC (RGBS) cables from the System 8/10 PLUS outputs to the
projector inputs according to the application requirements.
8. Apply Main Power to the System 8/10 PLUS by connecting the power cord. The
Main Power LED should light. Apply power to the projector.
9. Return System 8/10 PLUS and projector to normal operation.
Extron • System 8/10 PLUS • User’s Manual • P/N 68-415-01 Rev. B
Page 4
InFocus Installation
Configuration and Connections
InFocus LP 920 Projector Connections
Use the illustration below when connecting the System 8/10 PLUS to an InFocus
LP 920 projector. Refer to InFocus LP 920 documentation to continue the
installation.
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
Universal
Comm Adapter
26-467-01 "A"
A
9-Pin Male
9-Pin Female
RGBHV
S-Video
Video
CC Cable
15-Pin
Male
_ If the installation includes looping (master/slave) switchers, see Chapter 5.
If Video Loop Back is part of the installation, see pages 2-10 and 2-11.
Extron • System 8/10 PLUS • User’s Manual • P/N 68-415-01 Rev. B
Page 5
InFocus Installation
Configuration and Connections
InFocus LP 770 Projector Configuration
Verify that the System 8/10 PLUS is already configured for the InFocus LP 770
projector. The general setup is explained on page 3-4 and the switch settings for
the projector are repeated below.
1. Use a small screwdriver to remove the access cover from the System 8/10 PLUS
front panel. See bottom of page 3-3. The label on the back of the access cover
also has the configuration information.
__________ Before changing anything, remove the AC power cord to the System 8/10 PLUS to
verify that the main power is OFF; also turn the projector power OFF.
2. Set the switches as follows:
Config
Model
as
Rotary Switches Cable
RS1 RS2 RS3 RS4 J2/J3
InFocus LP 770
0
0
E
D
J2
SW15 Settings
1 2
3
4
5
6
Comm
7 8
↓ ↓ ↑ ↓ ↑ ↓
9 10
↑ ↓ ↑ ↓
Adapter
26-467-01
¯
ON
_RS5 is for RGB switching
delay. See page 3-4 for more
information on switch
functions.
1
2
3
4
5
6
7
8
9
10
SW15 DIP Switch
RS2
RS3
RS5 RS2 RS1
RS4
RS1
RS3 RS4
Configured For:
RS-232
3. Use a grease pencil (or other rub-off marker) to mark the space on the label next
to “InFocus LP 770”.
4. Locate the switcher’s Address DIP switches on the rear panel, lower right. Unless
this is part of a master/slave system, set #3 and #5 to the up position and the
others down. See illustration to the left.
Use the illustration on the next page to do the following steps.
5. Connect the Comm Adapter’s 9-pin male connector to the 9-pin female “RS-232C”
connector on the rear panel of the projector.
6. Connect the CC-50' (or CC-100') cable from the 9-pin male connector of the Comm
Adapter to the 15-pin HD “Projector Control” port located on the rear panel of the
System 8/10 PLUS.
______ Secure the screws on all D connectors.
7. Connect the BNC (RGBS) cables from the System 8/10 PLUS outputs to the
projector inputs according to the application requirements.
8. Apply Main Power to the System 8/10 PLUS by connecting the power cord. The
Main Power LED should light. Apply power to the projector.
9. Return System 8/10 PLUS and projector to normal operation.
Extron • System 8/10 PLUS • User’s Manual • P/N 68-415-01 Rev. B
Page 6
InFocus Installation
Configuration and Connections
InFocus LP 770 Projector Connections
Use the illustration below when connecting the System 8/10 PLUS to an InFocus
LP 770 projector. Refer to InFocus LP 770 documentation to continue the
installation.
REMOTE
○
VIDEO 1 VIDEO 2
USB
○
○
○
RS-232C
COMPUTER 2 IN AUDIO 2 IN
○
COMPUTER 1 IN AUDIO 1 IN
○
○
○
○
○
MAIN
S-VIDEO
VIDEO
○
○
AUDIO
○
○
COMPUTER OUT AUDIO OUT
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
Universal
Comm Adapter
26-467-01 "A"
A
9-Pin Male
9-Pin Female
RGBHV
S-Video
Video
CC Cable
15-Pin
Male
_ If the installation includes looping (master/slave) switchers, see Chapter 5.
If Video Loop Back is part of the installation, see pages 2-10 and 2-11.
Extron • System 8/10 PLUS • User’s Manual • P/N 68-415-01 Rev. B
Page 7
">