Sanyo Installation
Configuration and Connections
SYSTEM 8/10 Plus
PROJECTOR COMMUNICATIONS KIT
ATTENTION!
PLEASE READ THIS DOCUMENT FOR IMPORTANT
INSTALLATION INSTRUCTIONS
THIS KIT HAS BEEN SHIPPED WITH THE FOLLOWING COMPONENTS:
Kit Type: SANYO
Included Communications Adapter(s):
Quantity
1
1
Part Number
26-467-01
26-489-01
Description
ADP, UNV, “A”
ADP, UNV, “J”
THE TABLE BELOW LISTS THE POSSIBLE CONFIGURATION(S) AND CORRESPONDING
COMMUNICATIONS ADAPTER(S) FOR YOUR PROJECTOR MANUFACTURER’S VARIOUS
MODELS. PLEASE NOTE THAT YOUR SWITCHER HAS BEEN CONFIGURED AS
INDICATED BY THE “✔” IN THE “Config as” COLUMN. IF YOUR PROJECTOR MODEL
DIFFERS FROM THIS CONFIGURATION, YOU MUST RECONFIGURE YOUR SWITCHER
WITH THE CORRECT SETTINGS.
PLEASE REFER TO THE FOLLOWING PAGES FOR COMPLETE CONFIGURATION AND
SIGNAL CONNECTION INSTRUCTIONS.
THIS SWITCHER HAS BEEN CONFIGURED FOR:
Config
as
Model
SANYO PLC
Rotary Switches Cable
SW15 Settings
Comm
RS1 RS2 RS3 RS4 J2/J3 1 2 3 4 5 6 7 8 9 10 Adapter
✔
PLC
0
0
E
1
J2
↓ ↓ ↑ ↓ ↑ ↓ ↓ ↓ ↑ ↓ 26-467-01
✔
PLC 8810
0
0
E
1
J2
↓ ↓ ↑ ↓ ↑ ↓ ↓ ↓ ↑ ↓ 26-489-01
PLC XP10
1
0
E
1
J2
↓ ↓ ↑ ↓ ↑ ↓ ↓ ↓ ↑ ↓ 26-489-01
PLC XP30
3
0
E
1
J2
↓ ↓ ↑ ↓ ↑ ↓ ↓ ↓ ↑ ↓ 26-489-01
Extron • System 8/10 PLUS • User’s Manual • P/N 68-402-01 Rev. D
Page 1
Sanyo Installation
Configuration and Connections
Sanyo PLC Projector Configuration
Verify that the System 8/10 PLUS is already configured for the Sanyo PLC
projector. The general setup is explained on page 3-4 and the switch settings for
the projector are repeated below.
1. Use a small screwdriver to remove the access cover from the System 8/10 PLUS
front panel. See bottom of page 3-3. The label on the back of the access cover
also has the configuration information.
__________ Before changing anything, remove the AC power cord to the System 8/10 PLUS
to verify that the main power is OFF; also turn the projector power OFF.
2. Set the switches as follows:
Config
Model
as
✔
Rotary Switches Cable
RS1 RS2 RS3 RS4 J2/J3
Sanyo PLC
0
0
E
1
J2
SW15 Settings
1 2
3
4
5
6
Comm
7 8
↓ ↓ ↑ ↓ ↑ ↓
9 10
↓ ↓ ↑ ↓
¯
ON
_RS5 is for RGB switching
delay. See page 3-4 for
more information on switch
functions.
1
2
3
4
5
6
7
8
9
Adapter
26-467-01
or 26-489-01
10
SW15 DIP Switch
RS2
RS3
RS5 RS2 RS1
RS4
RS1
RS3 RS4
Configured For:
RS-232
3. Use a grease pencil (or other rub-off marker) to mark the space on the label next
to “Sanyo”.
4. Locate the switcher’s Address DIP switches on the rear panel, lower right.
Unless this is part of a master/slave system, set #3 and #5 to the up position and
the others down. See illustration to the left.
Use the illustration on the facing page to do the following steps.
5. Connect the Comm Adapter’s 9-pin male connector to the 9-pin female “Remote
1” connector on the rear panel of the projector.
6. Connect the CC-50' (or CC-100') cable from the 9-pin male connector of the
Comm Adapter to the 15-pin HD “Projector Control” port located on the rear
panel of the System 8/10 PLUS.
______ Secure the screws on all D connectors.
7. Connect the BNC (RGBS) cables from the System 8/10 PLUS outputs to the
Sanyo PLC projector inputs according to the application requirements.
8. Apply Main Power to the System 8/10 PLUS by connecting the power cord. The
Main Power LED should light. Apply power to the projector.
9. Return System 8/10 PLUS and projector to normal operation.
Extron • System 8/10 PLUS • User’s Manual • P/N 68-402-01 Rev. D
Page 2
Sanyo Installation
Configuration and Connections
Sanyo PLC Projector Connections
Use the illustration below when connecting the System 8/10 PLUS to a Sanyo
PLC projector. Refer to Sanyo PLC documentation to continue the installation.
See Special Note below
VIDEO/Y C/Cb(B-Y) Cr(R-Y)
S-VIDEO
VIDEO/Y C/Cb(B-Y) Cr(R-Y)
S-VIDEO
S-VIDEO
Composite
Video
AUDIO 1
R
USB 2
CONTROL PORT 2
L
AC JACK SERIAL PORT
L
S-Video
G
B
H
V
ANALOG RGB
L
ANALOG RGB
AUDIO OUT
R
ComAdapter
26-467-01 "A"
or 26-489-01 "J"
R
L
AUDIO 2
R
AUDIO 1
R
CONTROL PORT 1
L
AUDIO 1
R
VIDEO/Y C/Cb(B-Y) Cr(R-Y)
USB 1
AUDIO 1
R
L
9-Pin Male
A
9-Pin Male
RGBHV 5 BNC
9-Pin Female
* the projector’s S-Video DIN connector may also
15-Pin Male
be used for S-Video input
_ If the installation includes looping (master/slave) switchers, see Chapter 5.
If Video Loop Back is part of the installation, see pages 2-10 and 2-11.
9-Pin Female
9-Pin Male
To switcher's Projector Control port
A
To projector's Control Port 2
9-Pin Male
9-Pin Female
Special Note: _____ Certain PLC projectors may not come equipped with a 9-pin serial port
connector. In those situations, the Com adapter must be connected to Control
Port 2 using the projector’s special DIN to 9-pin serial adapter, as illustrated
below.
Sanyo DIN to 9-pin adapter
Extron Com Adapter
26-467-01 "A"
or 26-489-01 "J"
Extron • System 8/10 PLUS • User’s Manual • P/N 68-402-01 Rev. D
Page 3
">
